Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Riley Miller
2019-09-13 08:05:36

So I just replaced my LED screen last week, and the new screen already has two little burnt out spots after maybe 12 prints of use. When doing the UV detection test, additional bars show up and then the screen shorts out. What’s going on here? Is this just bad luck or is my machine the issue?

翻譯年糕

Ric Watts
2019-09-13 08:07:37

Riley Miller
2019-09-13 08:08:46

Ric Watts
2019-09-13 08:15:48

Riley Miller
2019-09-13 08:17:33

Ben Messer
2019-09-13 08:20:52

Mike Bauers
2019-09-13 08:21:20

Riley Miller
2019-09-13 08:21:35

Riley Miller
2019-09-13 08:21:51

Ric Watts
2019-09-13 08:23:26

Ben Messer
2019-09-13 08:23:30

Ric Watts
2019-09-13 08:24:16

Ben Messer
2019-09-13 08:25:52

Riley Miller
2019-09-13 08:29:47

Riley Miller
2019-09-13 08:31:40

Ben Messer
2019-09-13 08:32:53

Riley Miller
2019-09-13 08:47:51

Riley Miller
2019-09-13 08:48:03

Ben Messer
2019-09-13 08:52:21

Ric Watts
2019-09-13 08:52:21

Garret Bertrand
2019-09-13 08:58:02

原文網址 Riley Miller
2019-08-25 02:03:52

Hey guys, LCD just started burning out, are there any good recommendations for a cheaper replacement than the official Anycubic screen? So far I’m looking at the Epax screen but I can’t seem to figure out if it’s compatible with the Photon or comparable with it. In all honesty, unless some of you have experience with it, I’ll probably just suck it up and go for the official Anycubic screen. Thanks!
5.5" 2560x1440 Light Curing Display for EPAX X1 LCD 3D Printer

翻譯年糕

Alex Galvan
2019-08-25 02:12:14

Riley Miller
2019-08-25 02:13:07

Chris Koonce
2019-08-25 02:15:53

Scott Peterson
2019-08-25 02:17:45

Riley Miller
2019-08-25 02:21:30

Garret Bertrand
2019-08-25 03:09:56

Daniel Prows
2019-08-25 03:29:13

Ryan Dove
2019-08-25 04:31:24

Vinicius Silva
2019-08-25 10:02:42

Vinicius Silva
2019-08-25 10:07:47

Vinicius Silva
2019-08-25 10:11:22

Rolf Meijer
2019-08-25 15:50:08

原文網址 Riley Miller
2019-08-14 04:23:58

Could use some help! Been printing for a few months now with no issues, but for the last week my prints have just been failing constantly. Here’s an example of what that looks like. It’s a real mess, like the printer just kept most of the top part of the models from forming. Any idea what’s going on? I can post settings when I get home here in a bit. Currently using Anycubic Grey, haven’t changed my settings for about a month, did change out my FEP recently so maybe that has something to do with it?

翻譯年糕

Sean Croteau
2019-08-14 04:25:52

Chris Page
2019-08-14 04:37:18

Skyler Fike
2019-08-14 04:37:41

Riley Miller
2019-08-14 04:54:00

Riley Miller
2019-08-14 04:55:50

Gavin Paull
2019-08-14 06:57:37

Mike Olsen
2019-08-14 11:19:28

Chris Page
2019-08-14 13:09:12

Brent Eason
2019-08-14 13:27:36

Aaron Troxler
2019-08-14 17:25:49

Brent Eason
2019-08-14 21:36:56

Dick Teh
2019-08-14 22:22:38

Riley Miller
2019-08-15 10:10:09

Riley Miller
2019-08-15 10:12:10

Riley Miller
2019-08-15 10:13:35

Mike Olsen
2019-08-15 10:26:43

Joel Hallet
2019-08-15 10:32:35

Riley Miller
2019-08-15 10:38:19

原文網址 Riley Miller
2019-06-22 21:34:30

I’m afraid I suffered a home invasion by a coked up Velociraptor last night. While I was able to narrowly escape his claws as he leapt from furniture piece to furniture piece, screeching at me all the while about the obviousness of NASA’s conspiracy to fake the moon landing; my poor defenseless prints weren’t so lucky. ? Mr. Tank here was cut down in the prime of his life, his hull still strong, tracks polished and gleaming, and new well oiled engines ready to burst into life. May he rest in piece and find new life as a terrain piece on life’s many battlefields. ?

*Cues fields of Athenry

“Lowwwwwww lie the fieldssss of Athenryyyyyyy....” ? ? ? ?

Okay, now in all serious, what happened here, and how do I prevent it from happening again? ?

翻譯年糕