Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Sean Croteau
2019-08-18 03:00:06

Running siraya easy. I’m at .02um layer with 100s base exposure 8 base layers 14s exposure (per the test file). Is this unusual? Details were barely cured on the exposure sample. As in when I sprayed the test sample with ipa and wiped it most of the detail started to come away too.

翻譯年糕


原文網址 Sean Croteau
2019-08-17 00:37:32

I have to assume it's over-exposure or insufficient supports, but I can't find anything directly about it. I posted a few days back about a model that failed, I printed the base vertical (it has chamfered sides) and supported up the side where parts stuck out. seems within the bottom third of the base it split in half.

I had another part of the same build plate where the top of a part forms a partial spiral and that split at the top of the spiral.

I am using Siraya Easy, 7.5s exposure, 0.02 layer.

Is there a temperature effect with resins for shrinkage? the parts that split were both solid pieces without hollows.

翻譯年糕

Mike Fatchett
2019-08-17 00:45:34


原文網址 Sean Croteau
2019-08-15 11:25:50

How are you supposed to read this? This is the presliced .02mm

翻譯年糕

Trung Mi
2019-08-15 11:44:53

Sean Croteau
2019-08-15 11:48:26

Trung Mi
2019-08-15 11:51:42

Sean Croteau
2019-08-15 11:58:00

David Dorsett
2019-08-16 03:16:48


原文網址 Sean Croteau
2019-08-15 06:11:51

Ok. Continual failures of runs good once but there was a spot not supported right followed by same file supported well. But fails at start of print where the other time finished. Over and over. Stuck on what needs to be fixed at this point.

Leveling is either super finicky or I don’t know what “grabs the paper so it won’t go back in” means. I have tired compensating for poor base leveling with long exposure on the first 8 layers. Hasn’t made a big difference. I can’t understand how exactly to read that darned exposure test so I’m not sure if my layer exposure is actually right. But I am near the settings that the sheet shows for the same resin. My fep had to be replaced because I puckered it. I happened to do that again early on with this new one but a print came out ok with it like that. Then I tried to print again and it didn’t work. I found I’d tuned my fep wrong. Retuned it. Got a print. Now it fails again. What am I missing. I’m frustrated because I see what it can do but it won’t do it consistently.

翻譯年糕

Mike Fatchett
2019-08-15 06:19:21

Sean Croteau
2019-08-15 06:30:10

Daniel Ignacio Perez
2019-08-15 07:32:03

Stefan Giudici
2019-08-15 07:35:45

Sean Croteau
2019-08-15 08:53:50

Sean Croteau
2019-08-15 08:53:55

Sean Croteau
2019-08-15 10:32:41

Greg Chapman
2019-08-15 10:49:37

Sean Croteau
2019-08-15 10:55:47

Greg Chapman
2019-08-15 10:56:39

Sean Croteau
2019-08-15 10:59:03

Sean Croteau
2019-08-15 21:16:46

Sean Croteau
2019-08-15 21:17:31


原文網址 Sean Croteau
2019-08-14 06:48:01

So close ?

翻譯年糕

Sean Croteau
2019-08-14 06:59:45

Sean Croteau
2019-08-14 21:08:02


原文網址 Sean Croteau
2019-08-11 04:05:04

For those that do the Prusa slicer to Chitubox workflow, what are your support settings? Do you run the sl1 profile for supports? I set up a custom area to the photon print bed.

翻譯年糕

Chasen Harris
2019-08-11 07:17:13


原文網址 Sean Croteau
2019-08-09 07:39:53

So no squeak this time. But I’m definitely anxious about the fep. It had some puckers in it. Learning point. Only scrape your fep on a FLAT surface with nothing under it...we will see if the end of my trial bottle works out or I’ve blown most of it for no good result. Gonna change the fep next print when I go to change resin. Getting siraya easy orange next.

Is this ok or is it an issue? Anycubic green.

翻譯年糕

Vinicius Silva
2019-08-09 07:42:25

Terry Andrews Jr.
2019-08-09 07:50:17

Greg Chapman
2019-08-09 08:06:14

Terry Andrews Jr.
2019-08-09 08:09:00

Greg Chapman
2019-08-09 08:10:12

Casey R Marquardt
2019-08-09 08:15:12

Terry Andrews Jr.
2019-08-09 08:19:54

Gary Houser
2019-08-09 21:41:33

Sean Croteau
2019-08-09 22:41:54

Ryan Slater
2019-08-11 08:37:45

Sean Croteau
2019-08-11 10:56:57


原文網址 Sean Croteau
2019-08-05 22:26:30

Does anyone else get a high pitched squeak from their printer while it prints the first several layers, even when moving up after tightening the ball from leveling? What can I do to avoid this? I think this is the cause of my build plate shifting during prints, as I hear it until the plate stops shifting.

翻譯年糕

Richard Shapiro
2019-08-05 22:39:11

Chad Elstad
2019-08-05 22:40:35

Sean Croteau
2019-08-05 22:40:55

Sean Croteau
2019-08-05 22:41:12

Scott Pavlich
2019-08-05 23:21:43


原文網址 Sean Croteau
2019-08-05 02:14:14

Does it take anyone else 8 hours to prep a build file? I did a lot of manual supports, following FDM logic of "if it's hanging in space, it needs support" and it took forever going through the model after running auto supports, and even after Photon File Validator found unconnected pixels.

Anyone know a better/faster way to do supports? I'd like to make this as quick as it was to prep FDM files (a full build plate twice as large as the photon in 20 minutes).

Currently using ChiTuBox, and file validator.

翻譯年糕

Sean Croteau
2019-08-05 02:17:29

Noah Singer
2019-08-05 02:25:08

Will Koehler
2019-08-05 02:30:33

Mike Raines
2019-08-05 02:32:25

Gavin Paull
2019-08-05 02:37:28

Patrick Morgan
2019-08-05 02:47:45

Bob McGee
2019-08-05 02:48:05

Adam Musgrove
2019-08-05 02:51:07

Paul Songer
2019-08-05 02:52:59

Bob McGee
2019-08-05 02:56:20

Paul Songer
2019-08-05 02:57:51

Sean Croteau
2019-08-05 02:59:55

Sean Croteau
2019-08-05 03:00:18

Sean Croteau
2019-08-05 03:03:19

Bob McGee
2019-08-05 03:03:20

Sean Croteau
2019-08-05 03:04:13

Will Koehler
2019-08-05 03:05:52

John Boshier
2019-08-05 03:05:54

Mike Kelso
2019-08-05 03:06:16

William Riker
2019-08-05 03:15:15

Paul Songer
2019-08-05 03:17:54

Sean Croteau
2019-08-05 03:18:21

William Riker
2019-08-05 03:22:52

Sean Croteau
2019-08-05 04:18:22

William Riker
2019-08-05 04:20:04

George Bulte
2019-08-05 04:31:08

Sean Croteau
2019-08-05 04:46:51

William Riker
2019-08-05 04:50:11

Tim Moulton
2019-08-05 04:56:36

Tim Moulton
2019-08-05 04:56:48

Enrico Lopos Bertasi
2019-08-05 05:25:35

Stephen Farrell
2019-08-05 05:59:13

Tim Moulton
2019-08-05 06:00:19

George Bulte
2019-08-05 06:31:21

Bob McGee
2019-08-05 06:33:24

Bob McGee
2019-08-05 06:56:21

Justin Cupitt
2019-08-05 07:42:39

Sean Croteau
2019-08-05 07:46:57

Sean Croteau
2019-08-05 07:47:52

Maarten van den Heuvel
2019-08-05 07:49:10

Luccas Machado
2019-08-05 08:30:24

Joe Papa Behre Behrend
2019-08-05 09:18:07

Sean Croteau
2019-08-05 09:57:36

Sean Croteau
2019-08-05 09:58:28

Bob McGee
2019-08-05 10:09:35

Justin Cupitt
2019-08-05 10:18:41

Greg Kourakos
2019-08-05 10:33:25

Jarrad McDonald
2019-08-05 10:51:17

Valas Darkholme
2019-08-05 11:00:08

Valas Darkholme
2019-08-05 11:01:33

Valas Darkholme
2019-08-05 11:02:51

Greg Kourakos
2019-08-05 11:45:31

David Johnson
2019-08-05 11:55:16

伟洪
2019-08-05 12:21:18

Bob McGee
2019-08-05 12:22:31

Steven Molen
2019-08-05 12:23:27

Rohan O'Rourke
2019-08-05 12:32:53

Troy Tepes
2019-08-05 12:35:53

Troy Tepes
2019-08-05 12:36:48

Troy Tepes
2019-08-05 12:37:23

Bryan Mikolajewski
2019-08-05 13:53:08

Nathanial Hennekam
2019-08-05 15:53:32

Alex Burton
2019-08-05 18:12:03

Trung Mi
2019-08-05 20:29:19

Greg Kourakos
2019-08-05 20:29:58

Ludovic Noël
2019-08-05 21:16:25

Gabrielle Underhill Lucas
2019-08-05 21:30:51

James O'Keane
2019-08-05 21:31:27

James O'Keane
2019-08-05 21:31:53

Sean Croteau
2019-08-05 21:55:17

Sean Croteau
2019-08-05 21:56:28

Greg Kourakos
2019-08-05 21:58:12

Sean Croteau
2019-08-05 22:05:08

Sean Croteau
2019-08-05 22:07:26

Greg Kourakos
2019-08-05 22:15:17

Sean Croteau
2019-08-05 22:17:00

Greg Kourakos
2019-08-05 22:18:12

Sean Croteau
2019-08-05 22:20:58

Sean Croteau
2019-08-05 22:27:44

Steven Raybell
2019-08-06 02:56:29

Sean Croteau
2019-08-09 22:21:36


原文網址 Sean Croteau
2019-08-01 20:07:53

Arg! Build plate slid at an angle again. This time nice thunk at the start of the build then nothing on the build plate three hours later. I know it’s all on the fep now. I have two screws on the ball and still no good. Would this be resin on the ball? I really don’t think any got there because I haven’t overfilled it. But maybe it happened.

翻譯年糕

Tim Moulton
2019-08-01 20:11:44

Sean Croteau
2019-08-01 21:01:54

Fred Bey
2019-08-02 04:34:48

Sean Croteau
2019-08-02 07:02:05

Sean Croteau
2019-08-02 07:02:09


 

討論主題

全不選 常用關鍵字