Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Robert Barcus
2019-08-06 00:43:40

Im new to this so bear with me. My models seem so brittle that when I cut off the supports the surrounding areas crack and break off when I cut off the supports. Im dealing with mico model stuff. I try to be as careful and steady when I remove them, but have some difficulty in this process. I am curing them outside in the sun for a half hour, as I don't have a UV light setup at this time. Can someone suggest what the heck it is that I am doing wrong. I am using brand new clippers.

翻譯年糕

Lance Fulfer
2019-08-06 00:46:02

Andrew Parish
2019-08-06 00:48:56

Lorenzo Di Sante
2019-08-06 00:59:46

Richard Allsebrook
2019-08-06 00:59:59

Chris Bruce
2019-08-06 01:01:35

Andrew Parish
2019-08-06 01:06:16

Robert Jeppesen
2019-08-06 01:07:28

Ronin Gipijah
2019-08-06 01:07:59

Jeff Gowers
2019-08-06 01:09:07

Johannes Weis
2019-08-06 01:11:15

Joshua Collins
2019-08-06 01:11:21

Robert Barcus
2019-08-06 01:16:12

Robert Barcus
2019-08-06 01:16:43

Lance Fulfer
2019-08-06 01:21:01

James O'Keane
2019-08-06 01:33:48

Sean Craggs
2019-08-06 01:34:53

Quinn Mehling
2019-08-06 01:38:37

Mike Fatchett
2019-08-06 01:55:01

Jesse Mouré
2019-08-06 03:17:14

Aaron Michael Heine
2019-08-06 03:54:15

Sherri Johnson
2019-08-06 04:18:14

Sonny Green
2019-08-06 04:36:47

Kempster Kevin
2019-08-06 04:37:17

Bryan Mikolajewski
2019-08-06 04:47:46

Maarten van den Heuvel
2019-08-06 05:49:12

Michael S Dooley
2019-08-06 07:45:41

Deb Longoria
2019-08-06 08:02:30

Daniel Worden
2019-08-06 08:50:18

Nikolas Dandy
2019-08-06 10:09:30

Eileen Bowen
2019-08-06 10:21:18

Clint B. Kauffman
2019-08-06 10:34:44

Chris 'Peanuht' White
2019-08-06 10:44:43

Luke Mason
2019-08-06 11:39:19

Dương Quang Tấn Hùng
2019-08-06 12:11:50

Robert Cvengros
2019-08-06 12:36:38

Gregorey Savieo
2019-08-06 12:55:26

Pietro Malaguti Abbate
2019-08-06 21:35:56

Dave Williams
2019-08-06 23:09:22

Robert Cvengros
2019-08-07 00:57:57

Denis Maddalena
2019-08-07 01:15:41

Denis Maddalena
2019-08-07 01:18:18

David Samson
2019-08-07 09:36:38

Ed Gaulton
2019-08-10 23:15:14

Robert Nisson
2019-10-16 00:58:56

原文網址 Robert Barcus
2019-08-06 00:22:25

Has anybody printed a model under .05 mm with success? I have some tiny models that need to be printed and they failed at 05mm. I need to maybe print them at a finer resolution? The models in question are the size of dime and even smaller.

翻譯年糕

Niall Forrester
2019-08-06 00:30:25

Robert Barcus
2019-08-06 00:30:38

Tommy Killander
2019-08-06 01:07:51

Richard Allsebrook
2019-08-06 01:35:43

Jesse Mouré
2019-08-06 03:28:05

Lane Shutt
2019-08-06 04:34:14

Robert Barcus
2019-08-06 05:29:50

Michael S Dooley
2019-08-06 09:06:05

Sonny Green
2019-08-06 09:16:21

Sonny Green
2019-08-06 09:17:19

Chad Elstad
2019-08-06 10:13:20

Chad Elstad
2019-08-06 10:13:52

Justin Cupitt
2019-08-06 12:39:20

Mitchell Gardiner
2019-08-06 18:11:33

Nickolus Rodriguez
2019-08-06 18:18:12

Joel Ligeiro
2019-08-06 20:57:22

Denis Maddalena
2019-08-07 00:38:10

原文網址 Robert Barcus
2019-08-04 07:29:45

Do settings have to be change when you print with different color resins of the same resin manufacture? I swapped over to the gray color and now I get all failed prints! I ordered up some transparent green since this worked for me. I am new to this type of printing. Can some suggest here what the problem might be. Print sticks to the bed , but the rest of the print is a failure.

翻譯年糕

Brandon Levene
2019-08-04 07:33:16

Stefan Giudici
2019-08-04 07:52:47

Bob Deblier
2019-08-04 13:11:25

原文網址 Robert Barcus
2019-08-04 03:44:09

This is how I vent my anycubic Photon printer to get rid of the smell. I do my prints downstairs in our other living room. 99.9% of the smell from the resin is non-existent.

翻譯年糕