Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Danny Rosenthal
2020-01-10 08:20:06

I’ve had an issue my last 2 prints (two attempts at the same print) where the entire print (4 heroforge mini’s) fail at the same exact layer. It basically prints the rafts and a few layers of supports. Those layers printed to the build plate and then there’s another layer at the bottom of the vat.

This is coming off of about two months of flawless prints with no issues with adhesion.

Anyone ever had this issue?

翻譯年糕

Zachary Ford
2020-01-10 08:23:04

Danny Rosenthal
2020-01-10 08:24:02

Martina Prautzsch
2020-01-10 08:27:19

原文網址 Danny Rosenthal
2019-09-07 11:43:00

Hi all - I am trying to slice and support a miniature that has boots with spurs, which I am learning is hard to do with supports.

The part is so small that I can't even click on it to add supports to the island.

Is there any way (in chitubox) to override this so I can add a support to a tiny spot?

翻譯年糕

Sean Croteau
2019-09-07 11:45:13

Travis K. Jansen
2019-09-07 11:45:41

Danny Rosenthal
2019-09-07 11:46:26

Danny Rosenthal
2019-09-07 11:48:24

Chad Williams
2019-09-07 11:54:25

Caleb Custer
2019-09-07 12:05:44

Sean Croteau
2019-09-07 13:01:49

Joel Reid
2019-09-08 10:56:29

Greg Kourakos
2019-09-08 11:02:00

Jérôme Beyaert
2019-09-08 11:37:06

Greg Kourakos
2019-09-08 11:39:40

Jérôme Beyaert
2019-09-08 11:43:08

原文網址 Danny Rosenthal
2019-08-10 12:23:16

After a week of frustrating trial and error I finally found the best settings and got my build plate leveled correctly. At .05 layer height, I think my prints are starting to look pretty good. Thanks everyone for the advice and help!

Elegoo Gray
.05 Layer Height
10s exposure; 100s bottom

翻譯年糕

Aditya Chauhan
2019-08-10 14:05:36

Tauri Icenogle
2019-08-10 14:20:32

Mark Wardle
2019-08-10 22:14:01

原文網址 Danny Rosenthal
2019-08-07 05:39:58

Is it normal for prints to have a residual smell even after post-curing in a UV light? I feel like I’ve definitely cured it enough, but still it has a slight smell of resin.

翻譯年糕

Chad Elstad
2019-08-07 06:13:22

Bob Deblier
2019-08-08 18:56:53

原文網址 Danny Rosenthal
2019-08-06 12:06:10

Probably a silly question!

If I have no intention to paint a print from my Photon (they are DND minis), is there any reason to prime if I’m happy with the resin color? Does primer give any structural support? Or am I good to leave it without any coat?

翻譯年糕

洪碧娥
2019-08-06 12:11:59

Sergio Romero
2019-08-06 12:12:49

Chad Elstad
2019-08-06 12:23:55

Jesse Mouré
2019-08-06 12:39:25

Ines Silva
2019-08-06 16:09:21

原文網址 Danny Rosenthal
2019-08-05 06:39:33

Hi everyone, I just got my Photon a few days ago and I’ve only had intermittent success. I basically bought this printer exclusively for D&D miniatures, and I usually put three miniatures into Chitubox before I slice. I have, basically every time, had at least one of the miniatures not sticking to the build plate. Or sometimes, it initially sticks and I find out later that it fell off about a third of the way through (a very partially finished print will be in the vat)

Sometimes it’s the right side, sometimes left side, and most recently, the center miniature fell off. Brand new FEP, machine, everything. I’ve leveled with the flint read method, I’ve used the method Nick Williams posted, I feel like I’ve tried everything. This is getting truly frustrating.

Is there anything I may have missed?

翻譯年糕

Dean Drew II
2019-08-05 06:41:27