Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Adrian Dinca
2019-08-19 02:27:57

Ok guys, another noob question. How do you prevent the resin to flow between there indicated by the arrows when you turn the print plate around to remove a model. Now I'll have to take it all apart and clean it ?

翻譯年糕

Michał Wiśniewski
2019-08-19 02:29:40

Danny Lloyd
2019-08-19 02:29:46

Bruce Barton
2019-08-19 02:31:10

Scott Pavlich
2019-08-19 02:31:31

Zena Andreou
2019-08-19 02:38:13

Adrian Dinca
2019-08-19 02:47:42

Dustin Scott
2019-08-19 02:57:56

David Nicholls
2019-08-19 03:09:37

Robert Maefs
2019-08-19 03:11:20

Jared Zadorozny
2019-08-19 03:40:14

Kyle Calderwood
2019-08-19 04:03:30

Adrian Dinca
2019-08-19 04:16:21

Kyle Calderwood
2019-08-19 05:23:21

Chad Elstad
2019-08-19 05:48:00

Ironi R Johnson
2019-08-19 09:06:58

Joe Broggio
2019-08-19 21:22:07

Mark Wardle
2019-08-20 01:20:01

Mike Fatchett
2019-08-20 02:54:23

Luke Mason
2019-08-24 07:13:33

原文網址 Adrian Dinca
2019-08-16 00:19:41

Question: what does "frame sheering" mentioned in the 4.2.19 update for the Photon mean?

翻譯年糕

Andy Eakin
2019-08-16 00:38:43

Adrian Dinca
2019-08-16 00:43:30

Mark Wardle
2019-08-16 01:29:27

James Reedy
2019-08-16 01:32:49

Andy Eakin
2019-08-16 01:35:32

James Reedy
2019-08-16 02:17:27

Andy Eakin
2019-08-16 02:34:07

原文網址 Adrian Dinca
2019-08-09 05:38:44

Hi guys, does any of you happen to know what screws these are? I need to replace one as the hex head is not good anymore. Thank you in advance for your replies.

翻譯年糕

Damian Jerewski
2019-08-09 05:40:01

Adrian Dinca
2019-08-09 05:41:37

Damian Jerewski
2019-08-09 05:43:34

Adrian Dinca
2019-08-09 06:20:56

Vinicius Silva
2019-08-09 07:04:59

Vinicius Silva
2019-08-09 07:06:29

Vinicius Silva
2019-08-09 07:08:11

Alex Vee
2019-08-09 07:16:04

Vinicius Silva
2019-08-09 07:28:12

Adrian Dinca
2019-08-10 16:48:06

Adrian Dinca
2019-08-10 19:52:39

原文網址 Adrian Dinca
2019-08-07 21:48:28

Hi all, I'm new to this group so forgive me if this has already been asked. I recently purchased the Anycubic Photon printer and I only did a few prints on it and last time I did I got this, see pictures. So half of the print went ok then the resin started to clog / harden over the whole surface of the vat. Wondering what I did wrong on order to have successful prints in the future.

翻譯年糕