Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Mike McCreery
2019-11-22 05:23:39

Anycubic Photon owner here. I am a little disappointed in the machine. Having trouble getting prints to stick to the FEP and now the USB is showing issues with readability.

If you had a choice, what resin printer would you upgrade to?

翻譯年糕

Scott Roberts
2019-11-22 05:25:01

Tom Inglis
2019-11-22 05:25:02

Scott Roberts
2019-11-22 05:25:38

Richard Shapiro
2019-11-22 05:26:18

Mike McCreery
2019-11-22 05:26:55

Scott Roberts
2019-11-22 05:27:32

Scott Roberts
2019-11-22 05:28:07

Mike McCreery
2019-11-22 05:28:44

Brian L. Billo
2019-11-22 05:29:35

Alex Vee
2019-11-22 05:29:55

Scott Roberts
2019-11-22 05:30:07

Mike McCreery
2019-11-22 05:30:40

William Quayle
2019-11-22 05:33:03

Stefan Giudici
2019-11-22 05:35:35

Alex Vee
2019-11-22 05:39:48

Mark Rhodes
2019-11-22 05:42:28

Jason Andrew
2019-11-22 05:42:57

Ryan Neal
2019-11-22 06:21:01

Erik Pusch
2019-11-22 06:29:57

Robert Mun
2019-11-22 07:31:27

Scott Roberts
2019-11-22 07:32:15

Robert Mun
2019-11-22 07:34:16

Robert Mun
2019-11-22 07:35:25

George Bulte
2019-11-22 07:36:22

Scott Roberts
2019-11-22 07:36:36

Robert Mun
2019-11-22 07:37:57

Ryan Pearce
2019-11-22 08:59:25

Samson Chen
2019-11-22 10:06:32

原文網址 Mike McCreery
2019-11-16 02:49:49

My Anycubic photon has forgotten it's position. When I press home it tries to drive itself through the FEP. How do I re-calibrate the machine?

翻譯年糕

Ricardo Frederiks
2019-11-16 02:52:29

Paul West
2019-11-16 02:53:05

Paul West
2019-11-16 02:54:48

Paul West
2019-11-16 02:56:09

Mike McCreery
2019-11-16 03:03:52

Paul West
2019-11-16 03:04:47

Mike McCreery
2019-11-16 03:09:38

Paul West
2019-11-16 03:11:23

Mike McCreery
2019-11-16 03:13:15

Paul West
2019-11-16 03:18:09

Sen Kun
2019-11-16 04:45:16

Mike McCreery
2019-11-16 23:07:55

Paul West
2019-11-16 23:08:46

原文網址 Mike McCreery
2019-09-01 22:54:52

Good Morning! Thank you already for the amazing help I have received here. My photon has new firmware that is working properly and preventing me from having a nervous breakdown :]

I also have a 3D printed funnel to prevent hand cramping while trying to pour the resin from the vat back into the bottle while holding the filter up and away from the bottle attempting to center it. I am going to save a lot of resin.

Life is good!! Now, on to printing miniatures. Would you consider this a difficult miniature to support and what software would you use to create the supports? The Photon slicer's auto support didnt even catch 2 of the legs.

翻譯年糕

Stefan Giudici
2019-09-01 23:00:32

Mike McCreery
2019-09-01 23:01:26

Stefan Giudici
2019-09-01 23:04:14

Mike McCreery
2019-09-01 23:07:40

Stefan Giudici
2019-09-01 23:08:58

Mike McCreery
2019-09-01 23:11:12

Simon Booth
2019-09-01 23:16:03

Mike McCreery
2019-09-01 23:18:29

Simon Booth
2019-09-01 23:21:05

Mike McCreery
2019-09-01 23:22:29

Simon Booth
2019-09-01 23:23:26

Stefan Giudici
2019-09-01 23:23:54

Simon Booth
2019-09-01 23:23:55

原文網址 Mike McCreery
2019-08-30 06:42:05

Thank you for adding me. I am a very new photon owner. There is an issue that is frustrating me. I have already had to replace the FEP on my machine and might have to do it again. This morning I ran 4 or 5 prints of a single tiny ship with no problem. I ran my gloved fingers through the tank to confirm there was no buildup of resin. Then I tried to print 4 of them at the same time and I got this ghosting like I have gotten every single time I try to print multiple items. Also, there is now material stuck to the FEP film which I have to scrape off which scratches the film. What am I doing wrong??

翻譯年糕