Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Steven Terrill
2019-10-01 11:22:30

Still not super sure how to read this but I think column 6 looks best. Could anyone help me confirm and why? (This is Blu by Siraya Tech @ 30-33C)

翻譯年糕

Neil Duffey
2019-10-01 11:28:14

Ric Watts
2019-10-01 11:29:59

Steven Terrill
2019-10-01 11:32:43

Davoud Taghawi-Nejad
2019-10-01 23:37:43

原文網址 Steven Terrill
2019-09-20 05:01:20

Anyone seen this line on fep before? Very hard to see but runs the length of the left side of the photo. Not having print problems with it yet but I figured I'd check to see if it's a sign that fep will tear or just some left over markings from a large print

翻譯年糕

Jeremy LaPlace
2019-09-20 05:06:04

Jari Ivanoff
2019-09-20 05:09:44

Steven Terrill
2019-09-20 05:15:38

Victor Organek
2019-09-20 05:33:27

Victor Organek
2019-09-20 05:34:01

原文網址 Steven Terrill
2019-09-16 08:29:42

Photon File Validator: Who here uses it? Is your goal to remove every 'unsupported pixel' or only certain severity? I've noticed its very conservative and flags a ton of issues even for prints that appear to print just fine.

翻譯年糕

Chad Elstad
2019-09-16 08:41:28

原文網址 Steven Terrill
2019-09-14 23:47:00

Got new Anycubic Photon from Amazon after having issues with cured resin in my vat, however new printer appears to not resolve issue? Any ideas? Picture is the vat after running the test cube which printed absolutely perfectly. (Easier to see cured resin in the shadow)

翻譯年糕

Mike McCreery
2019-09-15 00:03:15

Steven Terrill
2019-09-15 00:05:26

Stefan Giudici
2019-09-15 00:26:05

Steven Terrill
2019-09-15 00:43:59

Tiernan Messmer
2019-09-15 08:05:38

Robb Nunya
2019-09-15 10:50:46

Scott Pavlich
2019-09-15 12:08:20

Jlee Usn
2019-09-15 21:49:45

Jlee Usn
2019-09-15 22:31:51

Stefan Giudici
2019-09-15 22:33:55

Jlee Usn
2019-09-15 22:35:46

Mike McCreery
2019-09-15 22:44:05

原文網址 Steven Terrill
2019-09-14 21:48:41

I was going to try the photon resin calibration code on github. I'm a little hesitant because the resin-xp-finder folder is listed as "deprecated". Is this no longer valid or am i not reading github right?

翻譯年糕

Tiernan Messmer
2019-09-14 22:25:23

Steven Terrill
2019-09-14 22:37:27

原文網址 Steven Terrill
2019-09-06 17:09:35

Good news and bad news. My test print looks like it came out perfectly however it looks like there's some other stuff in my vat. Isn't this usually indicative of an LCD issue?

翻譯年糕

原文網址 Steven Terrill
2019-09-06 07:14:00

Just subscribed to the Artisan Guild patreon. I noticed alot of models are in multiple pieces or at least with seperate bases. Is there an accepted best method for attaching models to bases? To you use resin and curing or some other method such as gluing or pinning?

翻譯年糕

Jesper Hvid
2019-09-06 07:17:35

Hugh Jeriolas
2019-09-06 07:18:29

Lucas Miguel
2019-09-06 07:19:15

George Bulte
2019-09-06 07:19:52

Steven Terrill
2019-09-06 07:26:58

Steven Terrill
2019-09-06 07:28:49

George Bulte
2019-09-06 07:30:16

George Bulte
2019-09-06 07:33:10

George Bulte
2019-09-06 07:34:22

Chad Elstad
2019-09-06 07:36:21

George Bulte
2019-09-06 07:37:02

Scott Pavlich
2019-09-06 07:44:01

Jesper Hvid
2019-09-06 13:36:46

Michael D Showalter
2019-09-06 20:55:16

原文網址 Steven Terrill
2019-09-05 09:28:47

Just attempted the test print and it failed but the really weird thing is I can't get the platform off now

翻譯年糕

Steven Terrill
2019-09-05 09:29:12

Manuel David Martín Marín
2019-09-05 09:35:28

Steven Terrill
2019-09-05 09:37:34

Steven Terrill
2019-09-05 09:37:56

Randall Martin
2019-09-05 09:39:39

Steven Terrill
2019-09-05 09:40:47

Randall Martin
2019-09-05 09:45:53

Steven Terrill
2019-09-05 09:48:08

Randall Martin
2019-09-05 09:50:25

Steven Terrill
2019-09-05 10:11:37

Randall Martin
2019-09-05 10:14:58

Michael D Showalter
2019-09-05 20:26:03

Steven Terrill
2019-09-05 21:55:01

Steven Terrill
2019-09-05 21:55:28

Michael D Showalter
2019-09-05 22:33:55

Michael D Showalter
2019-09-05 22:35:04

Steven Terrill
2019-09-05 23:34:04

Steven Terrill
2019-09-05 23:38:47

Randall Martin
2019-09-06 05:59:08

原文網址 Steven Terrill
2019-09-03 21:16:08

Getting my Anycubic Photon tomorrow. I've read through a lot of the great material the community has posted. One thing I haven't seen mentioned is how quickly the model needs to be removed and cleaned after a print finishes to present the uncured resin from masking details on the model. I'm thinking of having prints run while I'm at work. Would it be an issue if I don't get to the models until 3-4 hours after the print finishes?

翻譯年糕

Ian Golden Krasser
2019-09-03 21:17:44