Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Paul Lester
2020-03-05 11:47:02

Need some help doing some troubleshooting. Just switched to monocure 3D rapid grey, before that was getting butter smooth finish’s, went through the gdoc for settings and I’m getting these quality prints, supports are super hard to get off, where they use to just pull away with ease. Settings I’ve used as photo. Know it’s not wobble since I’ve used ac green and worked a charm

翻譯年糕

Paul Lester
2020-03-05 13:41:37

Paul Lester
2020-03-05 13:41:53

Paul Lester
2020-03-05 13:42:11

Paul Lester
2020-03-06 09:48:44

原文網址 Paul Lester
2020-03-03 17:05:29

So I’ve encountered an issue when replacing my FEP sheet, one of the screws that holds the 2 small bits of metal where the FEP sits between, one of them I’m unable to turn, the top of it is round. Suggestions on how to remove?

翻譯年糕

Richard Humble
2020-03-03 17:10:15

John Chrapkowski
2020-03-03 17:10:27

Paul Lester
2020-03-03 17:19:21

David Arnold
2020-03-03 17:49:59

Merv Hinton
2020-03-03 18:52:35

Janus Stark
2020-03-03 18:59:50

Mike Bauers
2020-03-03 19:05:38

Dominick Trascritti
2020-03-03 19:06:56

Ray Sears
2020-03-03 19:44:16

Scott Pavlich
2020-03-04 07:59:15

原文網址 Paul Lester
2019-11-27 19:01:38

Suddenly this is happening to my prints, it’s been leveled and all that Jazz, suggestions on what’s happening

翻譯年糕

Phil Ramey
2019-11-27 19:05:30

Paul Lester
2019-11-27 19:08:15

Patrick Haeflinger
2019-11-27 19:10:44

Paul Lester
2019-11-27 19:15:32

Paul Lester
2019-11-27 19:15:36

Paul Lester
2019-11-27 19:15:42

Paul Lester
2019-11-27 19:18:05

Paul Lester
2019-11-27 19:19:12

Adam Remington
2019-11-27 19:29:07

Kevin Delger
2019-11-27 19:38:59

Patrick Haeflinger
2019-11-27 19:58:14

Patrick Haeflinger
2019-11-27 20:00:19

Paul Lester
2019-11-28 03:05:21

Patrick Haeflinger
2019-11-28 03:19:17

Jose Alfonso Ortiz
2019-11-28 04:45:36

Paul Lester
2019-11-28 06:08:01

Patrick Haeflinger
2019-11-28 15:37:56

原文網址 Paul Lester
2019-11-02 04:53:53

Any suggestions on what I’m doing wrong. It seems every time I do a print, regardless of what I do, I have at least one that will stick to the FEP

翻譯年糕

Tom Howley
2019-11-02 04:55:45

Rastko Stanojevic
2019-11-02 05:28:45

Hugh Jeriolas
2019-11-02 05:42:20

Paul Lester
2019-11-02 05:45:40

Hugh Jeriolas
2019-11-02 05:46:12

Paul Lester
2019-11-02 05:46:25

Paul Lester
2019-11-02 05:47:04

Paul Lester
2019-11-02 05:48:14

Hugh Jeriolas
2019-11-02 05:51:50

John Chrapkowski
2019-11-02 07:19:34

Evan Boone
2019-11-02 07:22:10

原文網址 Paul Lester
2019-10-31 20:07:00

Hey guys, another question for you, roughtly how much time do i have from when a print finishes to making sure it goes under the UV light (or in my case, the sun), currently got a print that will finish slightly after midnight, and dont want to have a ruined print if i wait too long.

翻譯年糕

Brad Marsh
2019-10-31 20:16:22

Dominick Trascritti
2019-10-31 20:18:40

Aaron Wiggins
2019-10-31 20:26:56

Paul Lester
2019-10-31 20:47:16

Scott Pavlich
2019-10-31 20:48:46

Rastko Stanojevic
2019-10-31 21:03:37

Eric Pribish
2019-11-01 07:38:25

Stefan Giudici
2019-11-01 12:27:58

原文網址 Paul Lester
2019-10-31 08:09:24

Just trying to get some recommendations on what I should use to clean the prints here in Australia, access to IPA isn’t as easy as it is in the states. I’ve heard that using methylated sprits is fine but wanted to check in the with hive mind before I go out and buy all my extra stuff for my first print

翻譯年糕

Nick Eichler
2019-10-31 08:12:11