Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 TJ Strickland
2019-12-19 04:44:28

This is why I have trust issues... lol. Ran out of resin while i was sleeping.

翻譯年糕

Marie-Claude Rolland
2019-12-19 04:45:29

Nickolus Rodriguez
2019-12-19 04:48:45

Miroslav Zajíček
2019-12-19 04:51:16

Zach Huffman
2019-12-19 05:01:23

Tim Moulton
2019-12-19 05:22:07

Paul Krupa
2019-12-19 05:48:55

TJ Strickland
2019-12-19 05:50:19

Jose Alfonso Ortiz
2019-12-19 05:51:35

TJ Strickland
2019-12-19 05:52:29

Jose Alfonso Ortiz
2019-12-19 05:53:42

Bert Harvey
2019-12-19 06:48:21

Billy Thiex
2019-12-19 06:49:07

TJ Strickland
2019-12-19 06:59:28

Mark Dunmore
2019-12-19 07:06:28

Paul Soucy
2019-12-19 07:40:47

Clint B. Kauffman
2019-12-19 08:00:16

Clint B. Kauffman
2019-12-19 08:08:47

TJ Strickland
2019-12-19 08:17:58

Clint B. Kauffman
2019-12-19 08:46:30

Lee Perry
2019-12-19 11:16:53

TJ Strickland
2019-12-19 11:21:56

Paul Tucker
2019-12-19 20:20:49

Paul Tucker
2019-12-19 20:21:02

原文網址 TJ Strickland
2019-12-18 10:27:29

So, I have an issue. Whether I save a file as a photon or a chitubox project I can not get it to reopen after I close the program. It sits there for 10 minutes rendering the 3d image and then fails to load.

翻譯年糕

Randy Shepherd
2019-12-18 10:30:18

Mike Wheway
2019-12-18 11:14:42

Mike Wheway
2019-12-18 11:15:20

TJ Strickland
2019-12-18 11:17:41

原文網址 TJ Strickland
2019-12-15 12:40:45

Thanks to the support, advice, and knowledge of some you folks... I have my first successful print! Still needs a bit of clean up, but very happy!

翻譯年糕

原文網址 TJ Strickland
2019-12-14 20:14:06

So, I took yall advice to get my prints to stick (running one now and waiting in anxiety) but now I've noticed that when the bed rises between layers I hear a popcorn popping noise. Is that normal?

翻譯年糕

Justin Lincoln
2019-12-14 20:15:41

TJ Strickland
2019-12-14 20:16:19

Justin Lincoln
2019-12-14 20:16:57

TJ Strickland
2019-12-14 20:18:51

Andy Murtagh
2019-12-14 20:19:52

Bob Deblier
2019-12-14 20:23:44

Gregore Conn
2019-12-14 20:35:58

Ricky Cokely
2019-12-14 20:45:13

Tim Moulton
2019-12-14 20:59:18

Chad Elstad
2019-12-14 23:03:06

Ramiro Montes De Oca
2019-12-14 23:19:01

Jared Zadorozny
2019-12-15 11:58:14

Spencer Griffin
2019-12-15 18:36:14

Nigel White
2019-12-15 20:18:24

Chad Elstad
2019-12-15 21:42:22

原文網址 TJ Strickland
2019-12-14 05:38:31

Having some issues. This is the 3rd time I have had this failure and I'm not sure why. Brand new printer, test print went fine, plate is level, ambient room temp is around 65, everything has been cleaned. Settings are just the standard setting with 50 sec exposure for 1st layer. Ideas?

翻譯年糕

Sydnee Davidson
2019-12-14 05:41:47

Clarence Prigent
2019-12-14 05:43:28

Rastko Stanojevic
2019-12-14 05:45:53

El-Aras Buğra de Kabaca-Luchador
2019-12-14 05:51:01

Melecio Guzman
2019-12-14 06:06:27

Daniel McCutcheon
2019-12-14 07:27:11

TJ Strickland
2019-12-14 07:29:02

Steven Howland
2019-12-14 10:00:49

Michael Harvey
2019-12-14 10:10:24

原文網址 TJ Strickland
2019-12-11 09:26:26

So, a question I couldnt find answered anywhere. I see a lot of people post pics of their photons and you can see through the yellow glass. Mine however is not visible, but just yellow. No film on it I can find. Did some of them just get released this way?

翻譯年糕

Jeremy Babcock
2019-12-11 09:33:05