Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Mark Hume
2020-01-12 12:59:49

Is there a slicer software that has better user interface than either Photon Workshop or Chitubox? I am a decades-long user of AutoCad (which I use to generate my STL files), but I cannot utilize either slicer program in the way I'd like. Perhaps AutoCAD has spoiled me (in terms of user interface), or handcuffed me.

I cannot change viewpoint to see supports (i.e., from the bottom). I cannot add supports where they are obviously necessary, and I cannot eliminate supports that appear unnecessary. There's a button for both (add and remove), but I have yet to execute either command successfully.

Lacking a local (US) source of support, I cannot make sense of the programs and I'd welcome recommendations for another, with a local call-in help desk, preferably. Or perhaps, just a call-in customer support number.

翻譯年糕

Justin Miller
2020-01-12 13:09:05

Mark Hume
2020-01-12 13:09:57

Mark Hume
2020-01-12 13:12:01

Mark Hume
2020-01-12 13:14:15

Justin Miller
2020-01-12 13:16:01

Georg Zoeller
2020-01-12 13:31:30

Rob Walker
2020-01-12 14:08:29

Christopher Barnes
2020-01-12 14:27:38

Nipuna Gunarathne
2020-01-12 14:35:04

Johnny Grant
2020-01-12 14:48:31

Michał Krysiński
2020-01-12 17:41:15

Quol-Amin Impcasor
2020-01-12 18:41:03

Sander van Deijl
2020-01-12 18:53:09

Chris Holden
2020-01-12 20:03:19

Jason Spittles
2020-01-12 23:33:16

Mark Hume
2020-01-13 00:08:13

Georg Zoeller
2020-01-13 00:09:36

Mark Hume
2020-01-13 00:10:57

Mark Hume
2020-01-13 00:11:57

Mark Hume
2020-01-13 00:17:02

Mark Hume
2020-01-13 00:19:32

Mark Hume
2020-01-13 00:23:13

Christopher Barnes
2020-01-13 00:29:26

Mark Hume
2020-01-13 00:50:02

Georg Zoeller
2020-01-13 01:37:41

Mark Hume
2020-01-13 02:40:13

Mark Hume
2020-01-13 02:41:33

Chris Holden
2020-01-13 04:27:18

Mark Hume
2020-01-13 04:30:44

Mark Hume
2020-01-13 04:34:19

Chris Holden
2020-01-13 04:34:37

Chris Holden
2020-01-13 04:44:58

Chris Holden
2020-01-13 04:46:24

Mark Hume
2020-01-13 07:53:11

Keith Yinger
2020-01-14 00:54:49

原文網址 Mark Hume
2019-12-11 22:46:52

New to resin printing - I have a Photon S - I have not printed anything yet, but I have two questions about setting up the slicer (Photon Workshop) which I have tried to use: Can I change default units from metric to imperial? If so, how can this be done? Because units are in metric I need to print at a very specific HO scale (1:87.1 or 3.5mm = 12") and this creates upload problems in the slicer. How can I set that scale? I try to upload a model already in HO scale, but the slicer assumes metric units so the model inputs at the wrong size (it should be about 4.25" or 11 cm). Using either 1 or 2, how do I set this up?
I have not yet tried to input the "Full-scale" model (about 34' or 12 m long) and THEN reducing to HO scale. 翻譯年糕

Rikard Weijmer
2019-12-11 22:53:01