Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Bob Smith
2020-02-28 22:16:15

Is there any kind of usb hub that would work happily alongside the printer? All the constant connecting disconnecting is surely gonna make the one on the printer weaken over time and generate errors. Just a pitty octopi can't connect or am I wrong?

翻譯年糕

Bob Deblier
2020-02-28 22:18:06

Miles Redman
2020-02-28 22:18:43

Bob Smith
2020-02-28 22:24:02

Nipuna Gunarathne
2020-02-28 22:26:25

Ray Sears
2020-02-28 22:33:37

Nowo Kacyk Mowo
2020-02-28 22:34:13

Bob Deblier
2020-02-28 22:36:01

Ray Sears
2020-02-29 00:50:54

Bob Deblier
2020-02-29 02:29:57

David McGyver
2020-02-29 12:58:41

David McGyver
2020-02-29 12:59:07

Ray Sears
2020-02-29 19:28:12

原文網址 Bob Smith
2020-01-14 05:27:05

Experimenting with a incubator heater. So far so good. The housing is just temp as it was the only colors i had floating around at the time. Going to use black PETG when it gets here. The housing barely gets warm which is a plus. Setting the heater is easier said than done, but its getting there.

Update, I had an email from the manufacturer of the heaters and they told me "Regarding IncuKit Mini heaters. The circuit board has a function if the fan stops turning it cuts power to the heaters. So it is protected". So its a lot more safer than those PTC heaters!

翻譯年糕

Arnar Helgi Adalsteinsson
2020-01-14 08:08:46

Jc Nano
2020-01-14 08:24:18

Scott Hurd
2020-01-14 09:21:22

Bob Smith
2020-01-14 21:09:31

Bob Smith
2020-01-14 21:10:19

Bob Smith
2020-01-14 21:13:27

Arnar Helgi Adalsteinsson
2020-01-14 21:28:31

Nipuna Gunarathne
2020-01-14 23:52:47

Jc Nano
2020-01-16 08:14:42

原文網址 Bob Smith
2020-01-05 00:25:29

I'm surprised there isn't any mass produced heater for these printers which is why i think my prints are failing because the temperature withing the printer to keep resin temperature where it should be is not up to where it should be. I've seen ones made with a PTC fan heater on Thingiverse, which i suppose are OK until the fan fails, then from what I've seen on YT videos, thermal runaway starts and could start a fire with the filament used to hold in the PTC. Is there any out there, or plans of one being released?

翻譯年糕

Alex Vee
2020-01-05 00:27:28

Richard Humble
2020-01-05 00:29:20

Jeff Surma Jr.
2020-01-05 00:31:44

Bob Smith
2020-01-05 01:15:42

Bob Smith
2020-01-05 01:22:12

Richard Humble
2020-01-05 01:35:41

Fred Bey
2020-01-05 03:47:16

Jeff Greenfield
2020-01-05 12:54:37

原文網址 Bob Smith
2019-12-27 05:01:53

Still getting used to this kind of printing..Would something as simple as this stand attachment be placed "as is" or angled to the build plate with supports? Thanks.

翻譯年糕

Dustin Oliverius
2019-12-27 05:04:39

Matthew Auen
2019-12-27 05:09:00

Bryan Baena
2019-12-27 05:10:51

Susan Sioux Mercer
2019-12-27 05:38:18

Richard Burrell
2019-12-27 06:04:52

Dallas Winston Fitzgerald
2019-12-27 06:31:18

Jason Harris
2019-12-27 11:01:36

Antoine Andary
2019-12-27 19:33:49

Bob Smith
2019-12-27 22:07:51

Bob Smith
2019-12-27 22:09:06

Bob Smith
2019-12-27 22:10:03

Bob Smith
2019-12-27 22:11:02

Chris Shipman
2019-12-28 00:18:17

原文網址 Bob Smith
2019-12-25 07:41:51

Levelled the "Flint Read" way. Firmware was what came with the printer (3.4.1). I have since found out v5xx is the latest which is now installed.. The FEP was sound and yet as you can see, their test print failed about third of the way. Will the upgrade make any difference? Thanks in advance.

翻譯年糕