Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Scott Hurd
2020-01-09 02:01:37

Does anyone use Zortrax's Z-Suite to slice files or just Chitubox? I've used both just looking for feedback.

原文網址 Scott Hurd
2020-01-08 07:29:48

Having issues with prints sticking to build plate. Using Anycubic gray with 3 bottom layers. Bottom exposure is 30 sec. I've used these settings for about a year with no problem, but now nothing will stick to build plate. Changed FEP recently and printed just fine once. Any help would be appreciated.

翻譯年糕

Liam Foltz
2020-01-08 07:32:26

Scott Hurd
2020-01-08 07:33:50

Alexander Bayerdorffer
2020-01-08 07:36:29

Scott Hurd
2020-01-08 07:37:35

Liam Foltz
2020-01-08 07:38:01

Alexander Bayerdorffer
2020-01-08 07:38:05

Scott Hurd
2020-01-08 07:43:11

Scott Hurd
2020-01-08 07:43:52

Liam Foltz
2020-01-08 07:45:28

Scott Hurd
2020-01-08 08:18:20

Liam Foltz
2020-01-08 08:31:01

原文網址 Scott Hurd
2020-01-03 05:16:06

Having a weird issue with my resin, Anycubic Gray. When I leave it in the vat a couple days between prints, I get a strange gray film over the FEP. Only noticed it when I went to stir the resin in the vat before running some prints. Any ideas what this film is? It scrapes off with no damage to the FEP, just kinda odd.

翻譯年糕

Jean-François Meloche
2020-01-03 05:17:40

Jai Pate
2020-01-03 05:19:00

Scott Hurd
2020-01-03 05:19:00

Keith Yinger
2020-01-03 06:17:04

原文網址 Scott Hurd
2019-12-15 23:03:15

First time changing FEP. I messed up the one that came with the printer and now need to order some. I know thinner is better but how thin is too thin? Amazon has some in three thickness, .05, .1, and .2. microns. Which would be the best?

翻譯年糕

Scott Hurd
2019-12-15 23:03:59

Noah Belveal
2019-12-15 23:39:03

Noah Belveal
2019-12-15 23:40:35

Stefan Giudici
2019-12-15 23:47:20

原文網址 Scott Hurd
2019-08-11 22:23:47

I'm having a strange issue with the Photon Validator. When I load a file it runs fine till it reaches around the 1200 layer mark then it just stops and sits there. Anyone else have this issue?

翻譯年糕

Paul West
2019-08-12 00:20:39

Scott Hurd
2019-08-12 00:21:57

Aaron Wiggins
2019-08-12 03:58:06

Paul West
2019-08-12 03:59:12

Bob Deblier
2019-08-12 21:52:01

原文網址 Scott Hurd
2019-08-07 04:57:04

Having an issue. Ran the resin validation test. Put printer in test mode, ran test, put it back into print mode. Went to run a print and now the screen won't light up or the z axis won't move (see video). Any ideas?

Edit: after turning it of and on a couple times and rerunning the print program from the validation, it started working again. Must have just been a glitch somewhere.

翻譯年糕