Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Dave Aber
2020-02-08 07:42:01

So I am doing a 10 hr print. If it's set to finish aroubd 3 am would it be safe to leave in machine until 7ish AM before rinse?

翻譯年糕

Justin Talcott
2020-02-08 07:42:45

Tim Fitzmaurice
2020-02-08 07:42:47

Jean-Jacques Pasquin
2020-02-08 07:43:39

Jeff Surma Jr.
2020-02-08 07:45:30

Elissa Nuran Byer
2020-02-08 07:53:41

Chris Holden
2020-02-08 07:55:38

Mark Bryner
2020-02-08 07:57:00

Brendan Wood
2020-02-08 08:01:24

Dave Aber
2020-02-08 08:10:38

Paul 'Jam' Morris
2020-02-08 22:24:14

Chris Holden
2020-02-09 02:59:35

Chris Holden
2020-02-09 02:59:59

Tom Sargison
2020-02-09 18:26:36

原文網址 Dave Aber
2020-02-04 02:27:56

Okay. So I managed to get my file to start adhering to the build plate after leveling using the flint method. Heard the "pop" of layers peaking. Came back to check after 30 min and noticed that plate looked unlevel. So I redid the whole process and tightened the grub screw down good but seems like it's doing it again. Any suggestions appreciated.

翻譯年糕

Allison Janssens
2020-02-04 02:29:02

Marc Richards
2020-02-04 02:30:25

Cam Erasmus
2020-02-04 02:30:42

Pierre Eichel
2020-02-04 02:30:58

Dan Elent
2020-02-04 02:33:27

Dan Elent
2020-02-04 02:33:53

Jason Pedersen
2020-02-04 02:35:42

Valentin Ciotic
2020-02-04 02:55:39

Dave Aber
2020-02-04 02:57:57

Matthew Auen
2020-02-04 03:26:58

Bernhard Rubel
2020-02-04 03:47:14

Israel Martinez
2020-02-04 03:56:35

Israel Martinez
2020-02-04 03:58:35

Dave Aber
2020-02-04 03:59:47

Bernhard Rubel
2020-02-04 04:00:14

Dave Aber
2020-02-04 04:00:31

Matthew Auen
2020-02-04 04:03:39

Matthew Auen
2020-02-04 04:04:04

Dave Aber
2020-02-04 04:05:24

Matthew Auen
2020-02-04 04:07:54

Tom Sargison
2020-02-04 04:19:13

Denlee Paddy Rhodes
2020-02-04 05:46:39

Fred Bey
2020-02-04 06:44:04

Fred Bey
2020-02-04 06:49:00

Michael Power
2020-02-04 06:58:17

Dave Aber
2020-02-04 07:17:10

Dave Aber
2020-02-04 07:18:51

Tyron Craft
2020-02-04 09:39:16

Mike Fatchett
2020-02-04 10:40:50

Matthew Auen
2020-02-04 10:58:26

Paul West
2020-02-04 11:06:19

Matthew Auen
2020-02-04 16:07:21

Jarin Udom
2020-02-04 23:36:53

Gregore Conn
2020-02-05 06:19:26

Steve Ross
2020-02-05 07:55:23

原文網址 Dave Aber
2020-02-03 06:24:43

Looking for some help. Went to do first test print after leveling. I only have grey resin. This is what I came up with stuck to the vat. I'm assuming that I didn't have the plate down far enough when I leveled. However, every time I hit home after tightening, set Z and then confirm it seems like the paper is looser under plate. Any help is appreciated.

翻譯年糕