Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Troy Davidson
2020-03-24 04:39:41

When I replaced my lcd screen, it seems there was a "cover" on the old one. I assume this is to protect the lcd screen.

Is there anywhere to order this cover?

原文網址 Troy Davidson
2020-03-23 07:25:26

I cannot get my prints to stick to the bed. I've leveled the bed four different times, but it never works. I've done it twice with paper how Anycubic shows, and twice with the Flint Read method.

Is there something special I need to do to get the print to stick?

翻譯年糕

Liam Newman
2020-03-23 07:26:51

What's your bottom layer exposure time?

Jesse Ryan Chadwick
2020-03-23 07:26:54

I had to up my base exposure time to get anything to stick to mine

Robin MacNeil
2020-03-23 07:27:47

My exposure times were way too low. Followed this chart and have had no problems since: https://www.google.ca/url?sa=t&source=web&rct=j......

Troy Davidson
2020-03-23 07:29:06

I set my bottom layer exposure time to 90 seconds. I read that increasing it can help it stick.

Hank Perry
2020-03-23 07:31:08

I followed the recommendation for the resin for the settings and that worked. Slowed the prints down a ton, but works flawlessly now,

John Chrapkowski
2020-03-23 07:34:31

Mixed the resin good first right? And what’s the ambient temp?

Daniel Weatherhead
2020-03-23 08:07:46

The three steps I took, levelling one of them but up your exposure time to 80s for the bottom layers and update your firmware.

Troy Davidson
2020-03-23 09:07:04

So the prints are sticking to the plastic in the well and not the build plate.

Joel Isfeld
2020-03-23 09:14:19

If you are using photon workshop as a slicer check the first few layers. It was deleting my first layers for some reason.

Matthew W. Johnson
2020-03-23 09:33:58

Anyone else lube the FEP to aide in layer release?

Stefan Giudici
2020-03-23 12:38:08

Matthew W. Johnson no need, fep is a flouoropolymer, very slick on its own.

Juaco Amado
2020-03-23 22:07:48

Matthew W. Johnson is the FEP tight enough? Have you recently changed it?

原文網址 Troy Davidson
2020-03-22 02:12:30

I had to replace my lcd screen. I bought a screen off Amazon that said it worked with the Photon. When I got the new one, it has a silver back. Is this the wrong screen, or does that silver come off?

翻譯年糕

Sydnee Davidson
2020-03-22 02:14:38

Mine had silver, too. Though it looked more like a mirror. You’ll have to pull the film off and I imagine keep fingerprints off it.

Nipuna Gunarathne
2020-03-22 02:16:11

that's the backlight. these screens were made for smartphones so some come with the backlight. there are instructions on youtube on removing it

Richard Webb
2020-03-22 02:53:37

my screen came straight from anycubic - and is also silvered on the back as was the original one on the machine. the UV works fine through the silver layer

Troy Davidson
2020-03-22 03:01:04

Awesome. Thanks for the help. I was able to get it off and it's working good. I thought I broke the screen at first. There's a lot of layers you have to take off of for the back light.

Yasu Tano
2020-03-23 08:34:10

If its mirror reflective silver that's the lower polarizer and definitely not something to mess with.

If its a matte silver or grey silver then that's likely a backlight and needs to be removed.

原文網址 Troy Davidson
2020-03-08 10:28:02

I was just given a photon. I've done some initial prints, and things didn't go well. After digging deeper, it seems the LCD screen has gone bad. The person I got it from said they had an issue and the well leaked and spilled all over. They had to clean it out. I assume it was during this cleaning that the screen went bad.

Besides replacing the screen, is there anything else I should check to make sure is ok? Are there any "must do" tweaks? I've seen a few online, but they don't seem very important.

翻譯年糕