Anycubic Photon Printer Owners 造訪社團 » 用戶發文

Since it hasn't yellowed at all, it may be possible to increase he exposure a bit more.

looks like the circle could be fixed by putting a heavy support at the lowest point and standing it up a bit straighter.

The lines on the flat part are layer lines. that could be reduced by using antialiasing or standing up straighter

Your supports are off. They should support the edge towards the bottom as well. You can remove maybe 70% of the rest because they don't serve any purpose, but that bottom one at the lowest edge is crucial.

Corner of the X shaped rect. lost :(

You need to support the lowest points

Like the people before me already stated, your supports placement is wrong... You need to place a support at the point closest to the buildplate, in this case right on the edge.
As far as we can see in the pictures, your support is connected to the par t higher than where the lowest point of the part is.
This causes the edge 'to curl up' because it actually stays on the FEP until the rest of the part is printed and pulls it off the FEP.

14saniye exposure-50sn bottom exposure-bottom layer 8 ile photon'da bu reçineyi kullanıyorum. Herhangi bir sıkıntıya rastalamadım fakat piyasada bu reçineden bulamıyorum artık, siz nereden temin ediyorsunuz? Hikmet Gumus

Hikmet Gumus ?

Razor blade.

Use credit card

Yeah, scrape it off. If the resin leaks into the cracks around the screen you'll have to buy a new screen BTW, so might be a good idea to put some tape over them.

I'm afraid to scratch this surface ? If it's pla acetone solve this. But i don't know how to solve resin ?

As long as you aren't like gouging it into the screen you'll be fine.

I was pretty sketched out too, but I'm sure other people will say the same thing. You could also try alcohol wipes but I'm not sure if it will work

I haven't tried the acetone personally so I don't know how it would work.

I use the razor for clean the vitro surface

Disposable scalpel gives more control than a razor blade. You won't scratch the glass.

Solvents won't touch cured resin.

enamel paints thinner works great

Extremely hot water

Use razor blades. Don't soak in IPA it flows under the screen it loosens the double sized tape which holds the screen. Use razor blade or a Stanley blade in a 45 degree angle.

I used a plastic one, an poured a bit of ipa

then changed the fep

Roger Munguia you're right i ordered some already.

Wet the towel with isopropyl alcohol(ipa) and leave it on the surface of the screen for 5 min. It will loosen the resin residue. After that gently rub the ipa soaked paper towel to the screen.

Screen can be wiped with acetone. I vlean my screen with acetone and toilet paper... Works great (use triple ply for best results)

if the resin does not come out completely, you can use a steel spatula, well tilt, and scrape carefully.

Plastic razor blades. It'll get the resin up and won't scratch your glass.

Glass scraper

Soak a paper towel in ipa,wring it out so it's not dripping,lay on the screen,place empty vat on top to weigh it down. Let sit for five minutes and use plastic scraper to clean. You can also use cotton swabs dipped in ipa to scrub it off

Baby wipes are a good start, then razor blade to scrape off the hard stuff just go gentle with the bade. Same thing happened to me last week I had a pin hole on my fep

Can you use clear scotch tape to cover the places where resin would leak? (Like a shitty gasket?)

Yes my resin tank is leaking as well... any tips for preventing this? Also, how often should we replace the film?

Razor blade mounted on a glass scraper handle

Andy Turtle Consiglio kapton tape = win

Denis Jeleć Bender thank you!

Wet it with IPA and use a plastic scraper worked for me.