Anycubic Photon Printer Owners 造訪社團

原文網址 Justin Olsen
2019-12-19 23:44:15

Any reason there is zero curing after a print? Problem with the file or the hardware?

翻譯年糕

Tim Moulton
2019-12-19 23:45:28

Jake Campos
2019-12-19 23:47:43

Alex Payne
2019-12-19 23:48:52

Mike Wheway
2019-12-19 23:49:56

Frank LG
2019-12-19 23:51:48

Gary Noble
2019-12-19 23:51:56

Jared Zadorozny
2019-12-19 23:52:46

Patrick Haeflinger
2019-12-19 23:53:14

Jared Zadorozny
2019-12-19 23:53:34

原文網址 Jimmy Louis
2019-12-19 23:30:27

I'm finally getting my first round of failures... I'm not sure of I'm not exposing long enough for this model or WHAT the issue is, but I need your assistance...

Anycubic green... 74ºF ambient...settings in photos

last photo shows the point of failure... (the other two failures at 25º and 45º both failed at the tops of the supports where the model was starting to attach... this is the first that any of the model was actually printed instead of just a platform and a bunch of supports)

Thx

翻譯年糕

Joel Mendoza
2019-12-19 23:33:53

Jimmy Louis
2019-12-19 23:36:29

Matt Hooton
2019-12-19 23:37:09

Richard Humble
2019-12-19 23:44:09

Billy Emmons
2019-12-19 23:45:00

Steven Molen
2019-12-19 23:51:26

Jimmy Louis
2019-12-20 00:22:25

Matt Hooton
2019-12-20 00:58:45

Jimmy Louis
2019-12-20 01:11:24

Randy Shepherd
2019-12-20 07:14:47

Jimmy Louis
2019-12-20 08:49:34

Stephen Butt
2019-12-20 10:33:32

Randy Shepherd
2019-12-20 21:05:02

原文網址 Jaco Norchie Nortje
2019-12-19 22:29:28

Best Place for a replacment screen?

翻譯年糕

原文網址 Matthew Overbeck
2019-12-19 22:14:25

Got my photon just waiting for the resin (should have shipped together but oh well). While I am waiting I have a question other than space in a container is there a reason to take the print off the bed before ipa rinse? So if I made a custom rinse tank that would hold the bed suspended in the ipa with the print still attached so I could clean them together...? From what I can reason the ipa bath and an ultrasonic agitator should help the print releases from the bed with less effort and clean the bed at the same time.

翻譯年糕

Matthew Overbeck
2019-12-19 22:24:39

Bob Deblier
2019-12-19 22:24:39

Matthew Overbeck
2019-12-19 22:35:09

Bob Deblier
2019-12-19 22:37:32

Matthew Overbeck
2019-12-19 22:51:01

Bob Deblier
2019-12-19 22:52:53

Matthew Overbeck
2019-12-20 01:48:44

Stefan Giudici
2019-12-20 12:29:26

原文網址 Rick Champion
2019-12-19 20:19:28

Does anyone here know of a green resin similar to this ? Was thinking of mixing grey and green

翻譯年糕

Jake Walker
2019-12-19 20:21:18

Johnny Johnsen
2019-12-19 20:24:39

Johnny Johnsen
2019-12-19 20:25:52

Kevin Lems
2019-12-19 21:04:12

Estil Wade Taylor
2019-12-20 01:32:27

Rick Champion
2019-12-20 03:13:17

Rick Champion
2019-12-20 03:57:11

Bastian Dietert
2019-12-20 19:04:40

Bastian Dietert
2019-12-20 19:04:50

原文網址 Rick Champion
2019-12-19 18:31:30

So green or grey ?

翻譯年糕

Claudio Callegari
2019-12-19 18:35:37

Nicolas Tsagarides
2019-12-19 18:53:56

Rick Champion
2019-12-19 18:59:33

原文網址 Daniel Schwarz
2019-12-19 18:22:22

Ironman Hulkbuster

原文網址 Jane Leo
2019-12-19 18:11:12

Hi, this is my second print since purchased the machine. Default settings just adjust the anti alise to 8 and layer to 0.03. Missing part happens symmetrically. May I know if any one knows the cause?

翻譯年糕

Neil Ramsay
2019-12-19 20:51:09

Jane Leo
2019-12-19 22:14:53

原文網址 Mike David
2019-12-19 17:41:09

Unsure if anyone is in the same boat, kept stick insects before but want them again...their enclosure will be on 2nd storey with limited cooling so for hot days I'd want them in the garage where I use the anycubic photon which is somewhat toxic...has anyone stored stick insects and resin in the same room?

翻譯年糕

Ben Bicakci
2019-12-19 17:44:13