Anycubic Photon Printer Owners 造訪社團

原文網址 Robin Ter-Borch
2019-12-12 20:19:45

Will my print cure with this swedish weather? ?

翻譯年糕

Joel Reid
2019-12-12 20:20:27

Kristleifur Þorsteinsson
2019-12-12 20:22:06

Adam Widdowson
2019-12-12 20:25:42

Kelly Filgo
2019-12-12 20:31:00

Pablo Prades Gutierrez
2019-12-12 20:34:47

Robin Ter-Borch
2019-12-12 20:38:50

George Bulte
2019-12-12 20:41:26

Oleksandr Panforov
2019-12-12 21:06:49

Dan Andersson
2019-12-12 21:06:53

Adam Watmough
2019-12-12 21:30:54

Jose Garcia
2019-12-12 21:48:05

Mark Wardle
2019-12-12 22:03:35

Andrew Haagensen
2019-12-12 22:09:24

Dominick Trascritti
2019-12-12 22:52:54

Jeff Johnson
2019-12-12 22:58:25

Jimmy Gent
2019-12-12 23:27:03

John Chrapkowski
2019-12-12 23:33:47

John Chrapkowski
2019-12-12 23:34:49

Jeff Johnson
2019-12-12 23:49:11

Drew Pickard
2019-12-13 00:01:48

Henrik Thermansen Møller
2019-12-13 00:25:50

Mike Fatchett
2019-12-13 00:31:38

Christian Sargent
2019-12-13 00:47:08

Steve Nottingham
2019-12-13 00:59:23

Mats Larsson
2019-12-13 03:45:03

Joel Reid
2019-12-15 00:37:38

Melecio Guzman
2019-12-17 05:10:39

George Bulte
2019-12-17 05:13:57

原文網址 Rob Bowles
2019-12-12 20:02:19

Hi all.
I wanted to see what people thought might be the cause of what looks like a slight shift sideways during printing.

It was printed in the orientation I'm holding it in the first photo (with the build plate above it).

There's a little bit of what looks like resin clinging to some of the under hangs and I think that might be due to low temperature of the room the printer was in.
But I'm not sure what caused the big distortion.

EDIT: Added pictures of supports and settings.
Also, The resin is a mix of about 60/40 Anycubic Green and Anycubic Clear.

翻譯年糕

Richard Humble
2019-12-12 20:06:11

Rob Bowles
2019-12-12 20:41:23

Dan Andersson
2019-12-12 21:09:49

Rob Bowles
2019-12-12 21:17:05

Dan Andersson
2019-12-12 22:25:28

Richard Humble
2019-12-12 22:52:52

Rob Bowles
2019-12-12 23:49:37

原文網址 Dai Buckley Oam
2019-12-12 18:46:08

Seven Mandalorians.
Paid print for Treatstock.

翻譯年糕

Darren Donovan
2019-12-13 01:18:35

Dai Buckley Oam
2019-12-13 02:36:32

原文網址 Panos Dolly
2019-12-12 18:02:08

Hello everyone!

I get a prompt from chitubox to update to v1.6.1 from the 1.5.0 I now use.
Have you faced drawbacks? Should I follow chitubox's prompt?

翻譯年糕

Sen Kun
2019-12-12 18:06:09

Tiernan Messmer
2019-12-12 18:44:01

Sen Kun
2019-12-12 20:49:49

原文網址 Dave Green
2019-12-12 17:33:33

So I’m going for the in-line fan to carbon filter option for fume handling. My original fume extraction fan, as useless as it is grinds for a few minutes after startup.

Is it worth contacting anycubic to have a new one sent or can I just disconnect it and let the in-line fan do the extraction work?

翻譯年糕

Luke Mason
2019-12-12 17:42:25

Paul West
2019-12-12 22:44:33

原文網址 Mikel Deiman
2019-12-12 17:01:06

Just finished my first print with the Photon.

Used Geeetech Water Washable resin, color RED, but it is PINK! :(

Print quality itself is crisp, just washed it, now it is curing in the sun. still need to make a curing station :)

翻譯年糕

原文網址 Joshua Yates
2019-12-12 16:33:50

Has anyone who asked for a refund within 7 days of receiving the product actually got a refund? I've asked twice now and not had a response when confirming I want a refund.

翻譯年糕

Nathen Lentz
2019-12-12 16:38:27

Joshua Yates
2019-12-12 16:47:32

Stevo Hill
2019-12-12 16:49:17

Joshua Yates
2019-12-12 16:51:58

Sen Kun
2019-12-12 18:12:28

原文網址 Davide Rizzo
2019-12-12 15:00:02

First test print. No experience with 3D printers in my life. Just assembled, turned on and poured in resin. 1 hour later (and a probably over zealous safety clean) and it was done.

Absolutely blown away with ease and quality. Never seen a print this fast, smooth and detailed before ?

翻譯年糕