Anycubic Photon Printer Owners 造訪社團

原文網址 Alison Friedlander
2019-12-11 22:52:21

Any idea what would cause the prints to get so wobbly/distorted like this? Top ring should be circular like the bottom but very much isn’t and the same issue is present on the round flat top part.

Anycubic black resin and I printed 8 rings over the full build plate. Half of them came out perfectly and half (Towards the back of the plate)were distorted. I was thinking if it was a later shift or the build plate shifting they’d all be affected?

翻譯年糕

Matt Hooton
2019-12-11 23:21:10

Alison Friedlander
2019-12-11 23:29:37

Matt Hooton
2019-12-11 23:31:19

Alison Friedlander
2019-12-11 23:32:21

原文網址 Mark Hume
2019-12-11 22:46:52

New to resin printing - I have a Photon S - I have not printed anything yet, but I have two questions about setting up the slicer (Photon Workshop) which I have tried to use: Can I change default units from metric to imperial? If so, how can this be done? Because units are in metric I need to print at a very specific HO scale (1:87.1 or 3.5mm = 12") and this creates upload problems in the slicer. How can I set that scale? I try to upload a model already in HO scale, but the slicer assumes metric units so the model inputs at the wrong size (it should be about 4.25" or 11 cm). Using either 1 or 2, how do I set this up?
I have not yet tried to input the "Full-scale" model (about 34' or 12 m long) and THEN reducing to HO scale. 翻譯年糕

Rikard Weijmer
2019-12-11 22:53:01

Silas Bo Nielsen
2019-12-11 22:53:15

Minghua Kao
2019-12-11 23:01:35

Mark Hume
2019-12-11 23:47:24

Mark Hume
2019-12-11 23:48:27

Mark Hume
2019-12-11 23:49:10

Billy Emmons
2019-12-12 00:08:51

Ryan Miles Dika
2019-12-12 01:22:24

Rikard Weijmer
2019-12-12 03:35:00

Joe Brislane
2019-12-12 13:07:04

原文網址 Дамян Методиев
2019-12-11 22:44:12

Hello,

I ordered the printer and soon I will be part of you :P . But can you help me to find purple resin for this printer with delivery to Europe?

翻譯年糕

Francis X Benz
2019-12-11 22:57:39

原文網址 조남영
2019-12-11 22:14:38

Hello guys, I'd like to buy a resin.

Can anyone recommend me a resin that doesn't smell even if used in the room?

翻譯年糕

Mark Wells
2019-12-11 22:17:51

Francis X Benz
2019-12-11 22:18:45

Pierre Maugard
2019-12-11 22:23:10

Chad Elstad
2019-12-11 22:27:39

Nick Young
2019-12-11 22:41:09

Ian MacMillan
2019-12-11 22:45:17

Zach Kirk
2019-12-12 00:07:09

Petr Osipov
2019-12-12 00:46:38

Dan Andersson
2019-12-12 02:41:10

Dan Andersson
2019-12-12 02:44:05

Zach Kirk
2019-12-12 03:00:39

Petr Osipov
2019-12-12 03:43:55

Zach Kirk
2019-12-12 05:33:14

Dan Andersson
2019-12-12 13:12:34

Khristian Sutherland
2019-12-12 14:20:44

Khristian Sutherland
2019-12-12 14:22:30

Smith Hayward
2019-12-12 15:01:18

Smith Hayward
2019-12-12 15:02:04

Pierre Maugard
2019-12-12 16:23:52

Khristian Sutherland
2019-12-12 16:30:10

Pierre Maugard
2019-12-12 16:31:02

Ian MacMillan
2019-12-12 19:48:08

原文網址 Sergio Carreiras
2019-12-11 22:06:50

Hello! There is some upgrade for the photon file validator?

翻譯年糕

Kenneth Boshell
2019-12-11 22:35:29

原文網址 Mike Rea
2019-12-11 21:48:12

Anyone know why my Photon would make this noise on startup?

It stopped making this noise and made the usual fan sounds as soon as I hit stop recording, but it's still pretty concerning.

翻譯年糕

Dan Andersson
2019-12-11 21:52:57

Jason Andrew
2019-12-11 21:53:16

Kevin Robins
2019-12-11 22:08:11

Zachary Rollin Cantu
2019-12-11 22:30:06

Handrez Pintubola
2019-12-11 22:30:44

Handrez Pintubola
2019-12-11 22:31:28

Eduardo Parati
2019-12-11 22:53:24

Patrick Haeflinger
2019-12-11 23:34:43

Handrez Pintubola
2019-12-12 00:11:52

Michael M Thompson
2019-12-12 03:28:24

Dave Green
2019-12-12 04:02:09

原文網址 Simon C Day
2019-12-11 21:27:05

Any one have experience with RC31. Curious if it needs a special type of printer or not.

翻譯年糕

Simon C Day
2019-12-12 06:54:32

原文網址 Michael Fairley
2019-12-11 21:23:13

Good Morning All! I can’t find the answer in the search from the group. I just got the validated 2.0, but I can’t not get files from chitubox to open in it. Saved in .stl, .chitubox, and .obj with no luck. I read online it mentioned using a .photon file, but chitubox doesn’t have that as an option.

Thanks for any help!

翻譯年糕

Richard Humble
2019-12-11 21:34:21