Anycubic Photon Printer Owners 造訪社團

原文網址 Jeremy Evans
2019-12-02 03:28:22

Trying to figure out something to print on the ender 3 while my new hero me fan shroud is printing on the photon POST YOUR IDEAS Trying to figure out something to print on the ender 3 while my new hero me fan shroud is printing on the photon POST YOUR IDEAS 翻譯年糕

Joshua Alexander Gilpin
2019-12-02 03:47:31

Jeremy Evans
2019-12-02 03:53:55

Joshua Alexander Gilpin
2019-12-02 03:57:38

Joshua Alexander Gilpin
2019-12-02 03:57:47

原文網址 Ron Staton
2019-12-02 02:30:41

Does anyone know how to get more accuracy in my prints? Fitted parts that are printed don't fit together like they should. Not sure if pegs are thicker or holes are smaller... I'm using Elegoo ABS like grey and the prints look great but I think they could be more detailed. Maybe that's my problem but I'm not sure what setting to tweak for that. Any suggestions?

翻譯年糕

Aaron Shrive
2019-12-02 02:33:08

Paul Tucker
2019-12-02 02:33:25

Richard Humble
2019-12-02 02:36:03

Ron Staton
2019-12-02 02:37:34

Paul Tucker
2019-12-02 02:40:36

Will Koehler
2019-12-02 02:43:03

Patrick Haeflinger
2019-12-02 02:54:18

Bob Deblier
2019-12-02 02:58:35

Eric Green
2019-12-02 03:26:15

Fernando Daniel Pedrazzoli
2019-12-02 03:42:20

原文網址 Ryan Vogt
2019-12-02 02:17:53

Test print went off without a hitch. Seems that my sandbags didn't stick to the bed though.

翻譯年糕

Jordan Dowley
2019-12-02 02:24:59

Frank Martinez Jr
2019-12-02 04:50:50

Jordan Dowley
2019-12-02 04:51:49

Frank Martinez Jr
2019-12-02 04:55:39

Jordan Dowley
2019-12-02 05:18:07

Mel Danes
2019-12-02 09:30:08

Ryan Vogt
2019-12-02 09:52:55

Mel Danes
2019-12-02 11:45:31

Steven Howland
2019-12-02 12:40:49

原文網址 Dean Eyre
2019-12-02 02:00:02

Just a quick question I hope you can help. I might be doing this completely wrong but what do you lot do as a procedure, do you manipulate the STL, slice it then add supports, then save it and print. Is that the proper order.

翻譯年糕

Justin Coles
2019-12-02 02:02:17

Patrick Haeflinger
2019-12-02 02:11:38

Jeff Hunt
2019-12-02 11:00:34

原文網址 Edward Monteith
2019-12-02 01:56:24

Any one been able to find the MSDS sheet for this?

翻譯年糕

Jeff Greenfield
2019-12-02 09:22:22

原文網址 Jason Cartwright
2019-12-02 01:51:56

Is 99% IPA okay?

Or does it have to specifically be 91%?
And where's the cheapest place to buy IPA? Is 99% IPA okay?

Or does it have to specifically be 91%?
And where's the cheapest place to buy IPA? 翻譯年糕

William Boshoff
2019-12-02 01:53:41

Kevin Whiteside
2019-12-02 01:54:15

Dan Hjulberg
2019-12-02 01:55:18

Jason Cartwright
2019-12-02 01:55:53

Craig Riley
2019-12-02 01:59:41

Carlos Villamar
2019-12-02 01:59:57

Grant Weaver
2019-12-02 02:01:50

Andrew Gott
2019-12-02 02:05:50

Jason Cartwright
2019-12-02 02:06:01

Maggie Jenner-Bennett
2019-12-02 02:07:53

Matt Leese
2019-12-02 02:08:20

Dominick Trascritti
2019-12-02 02:11:45

Michael A Miller
2019-12-02 02:16:59

Paul Tucker
2019-12-02 02:30:16

Chad Elstad
2019-12-02 02:35:18

Gordon Wallace
2019-12-02 02:47:30

Jimmy Gent
2019-12-02 02:54:03

Chad Elstad
2019-12-02 02:59:43

Jimmy Gent
2019-12-02 03:08:47

Anthony Le
2019-12-02 03:56:52

Mike Stacey
2019-12-02 06:31:48

Giancarlo Arriola
2019-12-02 07:26:41

Luke Mason
2019-12-02 07:52:31

Sonny Green
2019-12-02 08:11:34

George Graves
2019-12-02 10:17:32

Michael Beal
2019-12-02 16:11:15

Tom Walton
2019-12-02 17:24:27

Robert Kyle
2019-12-05 23:52:50

Sergio PiRu
2019-12-06 22:34:21

原文網址 Peter Ring
2019-12-02 01:39:28

Question: I have recently changed my FEP film. I then had two good prints, but then the third one failed (didn't stick to the plate). I then releveled and tried again, but it still didn't stick. Could my fep film be too tight? Too loose? I am at a loss here. :(

翻譯年糕

Niall Forrester
2019-12-02 02:07:00

Peter Ring
2019-12-02 02:35:58

原文網址 Dany Bradet
2019-12-02 01:20:42

Is there a good deals that you know on Anycubic 1l Resin somewhere ?

翻譯年糕

Benny Lu
2019-12-02 01:56:34

Dany Bradet
2019-12-02 02:01:24

Milton Maxson
2019-12-02 07:17:46

原文網址 Pete Robie
2019-12-02 01:18:28

Used the base mesh in Zbrush to create a quick head to print off. Being my second print I'm pretty happy but I think I need to look at the settings for the Eco resin. I can see some ripples in the layers but I had the model face down and supported from behind. No issues on anything failing to print. I did accidentally forget to secure the base plate so I had to pause and then restart the print. I hope that didn't damage anything but it doesn't seem like it did.

翻譯年糕