Anycubic Photon Printer Owners 造訪社團

原文網址 Peter Ede
2020-01-29 09:37:16

What are peoples settings for the Anycubic ECO gray resin

翻譯年糕

Andrew Dunbar
2020-01-29 09:42:40

Tyron Craft
2020-01-29 09:42:54

Peter Ede
2020-01-29 10:28:36

原文網址 Nathan J Hunt
2020-01-29 09:22:45

Not sure if this is issue or not, but have started having this happen on starting print it lowers down into vat and does the set of beeps, all is fine printing layers, but when it gets to about layer five I hear a single beep come from printer when I got and check it seems ok... prints seem fine, could it be it's having issues reading from USB? or anyone else have a beep on printing a layer?

翻譯年糕

Stefan Giudici
2020-01-29 09:32:43

原文網址 Jeremi Finn
2020-01-29 09:09:17

Who uses flexible resin? I just got some Monocure Flex 100, and I remember reading a post a while ago about mixing it with regular resin... what ratio do you recommend for printing minis? Who uses flexible resin? I just got some Monocure Flex 100, and I remember reading a post a while ago about mixing it with regular resin... what ratio do you recommend for printing minis? 翻譯年糕

Paul West
2020-01-29 09:11:09

Chris Rogers
2020-01-29 09:39:20

Benny Lu
2020-01-29 10:26:45

原文網址 Joseph Daniels
2020-01-29 09:08:37

CRAP.

Bottom panel slipped off the table entirely during a screen replacement. Does anyone have a diagram of where the fan cables are connected and a good lead on a replacement if necessary?

翻譯年糕

John Aldred
2020-01-29 09:14:09

Nick Eason
2020-01-29 09:21:01

Joseph Daniels
2020-01-29 10:00:46

James Cachia-Garrett
2020-01-29 10:32:45

James Cachia-Garrett
2020-01-29 10:33:00

Alvaro Rodriguez
2020-01-30 03:12:53

Alvaro Rodriguez
2020-01-30 03:13:46

Alvaro Rodriguez
2020-01-30 03:17:30

Joseph Daniels
2020-01-30 03:18:00

Alvaro Rodriguez
2020-01-30 03:19:01

原文網址 Ben Wood
2020-01-29 08:42:57

Printed Spryo for the better 3/4s, was a good challenge for my 6th print and my largest, and again at least it's not a yoda XD. Couple bits of cleanup but it's good. Wings were separate, I'm not that capable haha.

翻譯年糕

Justin Lincoln
2020-01-29 08:48:22

Ben Wood
2020-01-29 08:52:14

Justin Lincoln
2020-01-29 08:54:00

Ben Wood
2020-01-29 08:57:47

Calico Deluca
2020-01-29 09:07:00

Ben Wood
2020-01-29 09:09:17

Calico Deluca
2020-01-29 09:10:14

Ben Wood
2020-01-29 09:11:05

Calico Deluca
2020-01-29 09:11:50

Brendan Wood
2020-01-29 09:12:27

Justin Lincoln
2020-01-29 09:14:02

Ben Wood
2020-01-29 09:16:28

Natasha Kerensky
2020-01-29 09:17:07

Ben Wood
2020-01-29 09:17:21

Calico Deluca
2020-01-29 09:18:37

Ben Wood
2020-01-29 09:20:12

Calico Deluca
2020-01-29 09:21:12

Calico Deluca
2020-01-29 09:21:39

Ben Wood
2020-01-29 09:22:14

Calico Deluca
2020-01-29 09:24:39

Brendan Wood
2020-01-29 09:28:49

Brendan Wood
2020-01-29 09:29:45

Kostas Yiatilis MacFarlane
2020-01-29 09:47:09

Ben Wood
2020-01-29 09:55:52

Sara Cruz
2020-01-29 15:45:53

Callum McIntyre
2020-01-29 17:31:15

Cam Erasmus
2020-01-29 19:26:51

Kostas Yiatilis MacFarlane
2020-01-29 19:28:03

Kostas Yiatilis MacFarlane
2020-01-29 19:28:38

Matthew Auen
2020-01-30 03:50:52

Andres Francisco Baeza
2020-01-30 04:13:55

Ben Wood
2020-02-07 02:29:11

原文網址 James Doby
2020-01-29 08:39:35

This can't be good

翻譯年糕

Jairo Ledesma
2020-01-29 08:46:12

Michael Miller
2020-01-29 08:57:16

Clayton Keller
2020-01-29 11:54:46

James Doby
2020-01-29 12:07:41

Mack Whillz
2020-01-29 12:52:53

Jim Nelson
2020-01-30 08:40:40

原文網址 Ken Chi Nok Ng
2020-01-29 08:36:08

The eyes

眼睛

· 查看原文 · 為此翻譯評分

原文網址 Rick Baxter
2020-01-29 08:33:39

Test print success, on first try even. I added a bottle of resin to my Photon order and apparently they ship a random one? Because I didn't get to choose it. Interestingly, they ended up sending me a bottle of the ECO yellow. I was expecting to hate the color but it actually looks really good.

翻譯年糕

Giosnò Dizze
2020-01-29 08:41:48

Giosnò Dizze
2020-01-29 08:43:00

Sean Brower
2020-01-29 08:49:48

Rick Baxter
2020-01-29 11:56:29

Natasha Kerensky
2020-01-29 12:02:38

Giosnò Dizze
2020-01-29 16:32:11

原文網址 Erik Morris
2020-01-29 08:11:28

Printing a Hero Forge Mini... For a friend. I'm sorta newish to the Photon, having a few successful printed minis under my belt. I've watched many great instructional videos on settings and support placements... BUT my buddy provided me with a hero forge STL that has the base and wizard robes so close that I'm not 100% sure how to support them without making a mess...

Any pro tips? With one of my examples, I made supports on the bottom of the base, then edited them to extend through the base to the bottom of the cloak.. it's hard to see exactly what I was doing... Any help (ideas) would be greatly appreciated.

翻譯年糕