Anycubic Photon Printer Owners 造訪社團

原文網址 Gabriel Guzman
2020-01-19 15:30:20

Prototyping... ?

翻譯年糕

Gary Bunda
2020-01-20 10:38:40

Gary Bunda
2020-01-20 10:43:58

Gabriel Guzman
2020-01-20 13:10:07

原文網址 Gabriel Guzman
2020-01-19 15:29:10

Tested the Printer with my signature piece (Peacock pendant) to see if the detail would be high enough Pretty happy with the result so far. Pictures of the cast piece shown for comparison.

翻譯年糕

Laurie Sinclair Muenchow
2020-01-19 15:39:04

Gabriel Guzman
2020-01-19 15:59:23

Fadi Ashush
2020-01-19 17:34:58

Gabriel Guzman
2020-01-19 23:53:34

Fadi Ashush
2020-01-20 01:08:07

Gabriel Guzman
2020-01-20 03:40:08

原文網址 Justin Hernán
2020-01-19 14:20:04

Would something like this air purifier be good for removing vocs and fumes from the air?
https://www.amazon.com/LEVOIT-Filtration-Eliminators-Vista-200/dp/B07Q1S7GGJ/ref=sr_1_6?crid=KY36PO20TPI1&keywords=voc+purifier&qid=1579414609&sprefix=voc+pur%2Caps%2C258&sr=8-6 翻譯年糕

原文網址 Luke Mason
2020-01-19 13:34:35

I thought I was ready, but obviously not. Which number? Multiply by 2?

Tore it getting it off the plate ?

翻譯年糕

Joshua Anderson
2020-01-19 13:39:02

Randy Shepherd
2020-01-19 14:47:09

Brad Thomson
2020-01-19 18:05:01

Joshua Anderson
2020-01-20 01:17:46

原文網址 Jeff Savoie
2020-01-19 13:29:43

Hello! I've finally made my first ever print with my new Photon S (firmware v2.9.9). I'm really happy because it was a success! But... there's room for improvement! I've lost a lot of details and I'm not sure what to do.

Here's a picture of the model/settings and some pics of the print. What should I do to get better quality and more details? I've tought of reducing the exposure time.

I've used Elegoo gray resin. I don't know if that matters, but the print was left suspended in the printer 4 hours before cleaning in alcohol (IPA).

Thanks for your help!

翻譯年糕

Edward Hill
2020-01-19 13:36:28

Alexander Bayerdorffer
2020-01-19 13:36:28

Alexander Bayerdorffer
2020-01-19 13:37:03

Jeff Savoie
2020-01-19 13:37:52

Jeff Savoie
2020-01-19 13:38:17

Edward Hill
2020-01-19 13:39:13

Alexander Bayerdorffer
2020-01-19 13:39:43

Edward Hill
2020-01-19 13:40:31

Luke Mason
2020-01-19 14:12:21

Greg Miller
2020-01-19 16:12:39

Luiz Junior
2020-01-20 01:28:39

Franz Meriles
2020-01-20 14:23:11

Kris Leon
2020-01-21 01:06:25

原文網址 Griffin Smits
2020-01-19 13:22:14

Hi guys. This is my second print on my photon. I noticed it began peeling off the build plate so I stopped it. Is this caused by bad leveling, or too much suction? Is this why you should hollow bigger models to reduce suction? Thanks! Models are by the artisans guild. 4th picture is my successful print before this failure.

翻譯年糕

Alexander Bayerdorffer
2020-01-19 13:29:00

Tim Moulton
2020-01-19 13:53:59

Cory Curtis Merrill
2020-01-19 13:55:29

Tim Moulton
2020-01-19 13:55:34

Clint B. Kauffman
2020-01-19 13:58:27

Griffin Smits
2020-01-19 14:01:29

Kris Leon
2020-01-19 14:16:30

Ben Brooks
2020-01-19 15:51:08

Richard Humble
2020-01-19 17:24:19

Liam Plotts
2020-01-20 03:50:12

Griffin Smits
2020-01-21 11:57:44

原文網址 Ken Ishio
2020-01-19 13:12:32

Waxcast by makerjuice. Advertised at 40s per level. Been trying to get it right.

What do you guys think? Printed using 25u 10-100 calibration file. The far right is the 10th column.

Update. I did the 20-200 file....and it looks about 140s wow. Is this normal?

翻譯年糕

Noah Lothes
2020-01-19 13:17:55

Ken Ishio
2020-01-19 13:18:34

Ken Ishio
2020-01-19 13:19:29

Stefan Giudici
2020-01-19 14:00:25

Noah Lothes
2020-01-19 14:06:38

Stefan Giudici
2020-01-19 14:11:41

Ken Ishio
2020-01-19 14:44:05

原文網址 Gaze Hound
2020-01-19 12:43:48

how far off of the bed do you normally place a part? i been running into problem of when i put it flat on plate of off a little it get to were it won't let me put any bracing

翻譯年糕

Matthew Steeghs
2020-01-19 12:56:56

Андрей Шестаков
2020-01-19 13:08:08

原文網址 Андрей Шестаков
2020-01-19 12:35:16

Just a figurine :) The total height is 100 mm. Layer 50 μm, 6 seconds per layer, Anycubic Skin resin mixed with Anycubic Black. Primed from an airbrush. Lumpy surfaces are not a print defect; this is such a lumpy model. In it, only face and hair are smooth. Modyfied Anycubic Photon S.