ATOM 3D Printer Group 造訪社團 » Kisslicer

原文網址 李英任
2015-08-12 11:50:37

請問一下適用上面那個設定檔的文件去覆蓋下面那個資料夾的根目錄嗎?
可是我在覆蓋後準備開始程式時似乎跳出無法解讀的通知
而且在進到裡面後發現參數似乎還是kisslicer預設值而不是atom參數
是有哪一步做錯了嗎?

Charlie Ting
2015-08-12 12:14:34

程式目錄要放在系統碟才行

李英任
2015-08-12 12:15:33

系統碟是指什麼呢？我有把那兩個資料夾都放在c槽裡

MoMo Yang
2015-08-12 12:17:43

目錄不能是中文的

Clarence Lee
2015-08-12 12:18:47

kisslicer目錄放在單純的路徑下..像是c:\
不要放桌面...中間卡中文或特殊字元比較會出狀況找不到設定檔

李英任
2015-08-12 13:26:44

問題以排解,謝謝大家~

原文網址 林祐德
2015-08-11 20:34:40

測試報告~ 目前abs不開熱床，用abs juice+brim。印出10*10，ok不會翹曲~ kisslicer brim 15mm, high 1.2 checked - brim fillet. juice不像youtube塗薄薄一層，而是有點厚度。如果摸起來有光滑感就會失敗，要摸起來是粗糙感才ok。 abs後處理的物件看起來就是~~~爽~~~
另外還有一招，物件下層再畫一層薄薄的圓形raft(印出來後剪掉)，再開brim。

原文網址 嚴鈺瑋
2015-08-10 11:18:45

我想請問一下
我想製作圓球體實際做出的都會跟kisslicer
一樣呈現多角的圓球體，無法製作出光滑面的圓球體，是軟體的問題嗎？有解決的方法嗎？

幼稚達
2015-08-10 11:23:54

轉stl時三角形多給一點

Adrian Sung
2015-08-10 11:54:46

所見即所得，如樓上，增加球體的網格量即可

陳順得
2015-08-10 12:04:06

邊長減短，法線減短，就會變得比較細緻了

嚴鈺瑋
2015-08-10 12:06:00

不太懂，其實我畫很多圓形的東西但是轉檔出來在kisslicer都會呈現多角狀態

藍濬煜
2015-08-10 12:07:51

你要再3D製作軟體先柔化轉高面數啦~

陳順得
2015-08-10 12:08:12

因為STL檔不會是真正的圓形，而是無數三角形組成的，所以在你畫好模型轉成STL檔的時候，要把精細度開高一點，不然最粗糙的情況下，圓形甚至會變成八角形

彭書偉
2015-08-10 12:13:23

Kisslicer pro 中有個oversample resolution 數值調0.05應能解決，但pro要付費$41美元的樣子

高北熊
2015-08-10 12:14:02

你可能要跟大家說一下你用那款建模軟體

彭書偉
2015-08-10 12:14:17

Oversample resolution =1

彭書偉
2015-08-10 12:14:53

Oversample resolution = 0.05

嚴鈺瑋
2015-08-10 12:27:16

我是用solid Edge軟體在繪畫
如何柔化在轉高面數？
所以只能用付費的功能下去修改嗎？ …… 查看更多

高北熊
2015-08-10 12:52:38

https://www.youtube.com/watch?v=Akq6_q8JcsM
匯出STL的時候
Option內的參數要調整，會影響輸出模型的品質

嚴鈺瑋
2015-08-10 14:56:09

感謝高北熊我直接按照你提供的影片修改轉檔完就是光滑面了,也感謝其他人寶貴的意見

曾俊維
2015-08-11 14:20:28

那請問sketchup的話有那種地方可以調呢？

李英任
2015-08-11 15:22:38

sketchup再建模的時候旁邊就有參數可以讓他更圓滑,因為他的圓是由正多邊形組成,可以透過調整邊數讓圓更圓滑

曾俊維
2015-08-11 16:07:57

在那調整呢？不好意思，新手，不是很了解。

李英任
2015-08-11 16:11:04

首先先画一个圆，然后选择这个圆的边线（记得是圆边不是圆面）,点击右键，选择第一个选项"实体信息"，便可以更改圆边段数，默认是24段。

曾俊維
2015-08-11 16:16:14

我找到了，感謝你

原文網址 Vincent LM Yeh
2015-08-06 13:36:15

[G29與玻璃平台平整度測試]
按照流程操作
(1)把口紅膠洗乾淨，貼上藍膠帶(TH=0.2mm)
(2)放上平台鎖緊，好好鎖緊XD
(3)放慢速度跑G29
(4)把Spiral檔案用Meshmixer調整成包外尺寸=190mm(怕噴頭撞螺絲)
(5)Kisslicer裡面拿掉G29 Z+0.45
(6)Kisslicer裡面設定Z Offset=0.65(原來可行的0.45加上膠帶的0.2)
更新：Z Offset=0.60~0.55 第一層會黏的比較緊

(7)切片丟機器列印，感覺還不錯
PS.第一次調整時，把Z lift與Z Offset弄混，結果噴嘴直接劃破膠帶

Vincent LM Yeh
2015-08-06 13:48:57

補充一下，藍色膠帶在B&Q也買的到。去油漆材料那邊找3M遮蔽膠帶就是了。以前買來固定草圖紙用的，沒想到3D列印也好用，3M真是惠我良多。

吳旭倫
2015-08-06 16:15:18

B&Q賣的是2080吧,一般3D列印用的應該是2090,型號不太一樣,我用2080黏不太住...

Vincent LM Yeh
2015-08-06 16:35:07

我買到2090喔

Charlie Ting
2015-08-06 22:45:31

重點是多少錢？B&Q的東西通常都比較高貴 XD

Vincent LM Yeh
2015-08-06 23:22:13

忘了多少錢了，不過B&Q的東西確實較貴，我是因為家裡附近就有一家，買東西方便所以常去。

Vincent LM Yeh
2015-08-07 00:28:54

查到了，一卷105台幣，不知有沒有比較貴。 http://www.i-house.com.tw/product/detail/id/137070

原文網址 Max Lu
2015-08-04 09:43:20

昨天清理了噴頭且找出快速接頭內的斷料原因候，再次設定了KISSlicer並且不調整面板，再半夜兩點去看製作狀況還算不錯，就再次放著製作到早上，雖然早上起來已經完成但卻又發現小狀況.....

再頂部就又開始沒有出料的跡象導致沒有封頂，再擠料馬達處發現很多削削再CNC的送料口處。

廖新弘
2015-08-04 09:50:21

先量一下PLA的缐徑，因為你習慣在半夜印，所以擠出馬達那邊有什麼狀況你無法告知大家，所以很難判斷

Max Lu
2015-08-04 09:53:48

只能回家再量看看了，因為早上要上班所以製作的時間除了假日可以一整天，其他都只能在晚上製作了。

廖新弘
2015-08-04 10:01:00

那建議先印一些簡單的東西，摸熟了再拉長時間

原文網址 Birk Binnard
2015-08-01 22:46:29

Not watertight?

These photos show a small vase I made that leaks. It looks like the leak happens at the seam created by Kisslicer.

I'm hoping this problem is unique to this particular vase, but I will test other ones I've made. Has anyone else tried this?

翻譯年糕

Mariel Diaz
2015-08-02 07:13:43

I think is the same for the most of the vases created by kisslicer, i have the same problem :S

Birk Binnard
2015-08-02 08:33:47

I recently bought Simplify3D and will do a test with it. Hopefully it will be better.

Po Ting Liu
2015-08-02 09:34:21

I've tried it before, it works with having your wall thickness to 3mm and at least 80% infill

Clarence Lee
2015-08-02 10:38:10

https://groups.google.com/....../ZbDBK_Th-kU/wqOpdNdivdoJ

Po Ting Liu
2015-08-02 11:09:59

setting to 1.2mm shell thickness also works!

原文網址 Danny Kuo
2015-07-31 08:47:49

請問各位~使用 Kisslicer 時 G-cade的設定，除了設定開始與結束的動作之外~可以在列印到某層結束時做出指定動作嗎?
是不是能再圖中紅色框框中設定呢?
有人使用過嗎?

陳奕丞
2015-07-31 08:57:38

讓機器休息一下，叫蜂鳴器唱首歌XD?

Danny Kuo
2015-07-31 10:08:25

列如:暫停->回抽->升Z軸->手動換料

李穆
2015-07-31 10:31:19

那個我上週去上課時提出過，好像是每n層就會執行一次，對於單點停留就不太方便。建議還是自己開切出來的gcode去插入

Clarence Lee
2015-07-31 10:32:21

N[*] layers – code to be inserted every * layers. The * value is set on the text field at top left of Gcode Tab

Charlie Ting
2015-07-31 10:35:42

專業技能

原文網址 Roy Lo
2015-07-30 11:25:32

有誰知道Kisslicer 怎麼設定, 讓棧板容易拆除?

廖新弘
2015-07-30 11:41:10

那要自己修改G-code，kissliver這點比較弱

Roy Lo
2015-07-30 11:51:29

;LAYER:0
M221 S40
M104 S210

Roy Lo
2015-07-30 11:52:14

;LAYER:1
M221 S100
M104 S220

Roy Lo
2015-07-30 11:53:00

是改gcode 這兩個地方嗎?

廖新弘
2015-07-30 12:13:49

M104是溫度控制，所以不是改那邊

原文網址 Birk Binnard
2015-07-29 23:16:26

Big and Little

Photo 1 shows the largest part (Big) I have printed so far. It is a little more than 200 mm high and used about half a reel of PLA filament. I designed the part and have tried to print it several times, but up to now I have only been able to print small versions of it becuase the slicers I've used would not slice the full size part. Yesterday I purchased the Simply3D slicer and it allowed me to print the full size part successfully.

Photo 2 is a smaller version (Little) I printed a few days ago. I used Kisslicer to prepare the GCode for printing.

Photo 3 shows Big on the printer at about 92% complete after 19 hours of printing.

Photo 4 shows the part's 2-layer design; it is hard to see the infill that is about 15%.

Photo 5 is Big & Little together. After looking at the tool path for Big I decided to change the design a bit; Big has fewer ribs than Little to make the hills and valleys more evenly spaced, and there a a bit more twist at the top which gives the part a more consistent look.

Based on this result I'd say the combination of the Atom2 printer and the Simplify3D slicer makes one of the best 3D printing solutions available today.

翻譯年糕

Charlie Ting
2015-07-29 23:38:36

Good job!

Samuel Chiou
2015-07-30 00:09:27

Cool!

Harry Cayne
2015-07-30 01:07:04

does it worth to switch to Simply3D, you can see a big difference in quality vs kisslicer?

Birk Binnard
2015-07-30 02:16:08

Harry - yes. Although Kisslicer is good in many respects, I found that it creates bad tool paths on some of my larger, more complex models. It also sometimes leaves small globs at the start or end of a layer extrusion, even after I have experimented with quite a few different Prime/Suck settings.

I agree it is expensive software, and I held off buyiung it for quite a while (longer than I should have actually.) I have only had it for a day and a half now, but it does slice parts that no other slicer will - and I've tried them all. It also has part repair functions that take the place of things like Netfabb, Meshmixer, etc.

My bottom line is - if you are serious about 3D printing, get Simplify3D.

徐凡
2015-07-30 11:29:35

This is the list of supported printer of Simplify 3D, but i can't find ATOM2. So, How do you make this work? https://www.simplify3d.com/software/supported-printers/

Birk Binnard
2015-07-30 11:36:14

I may be the only Atom2 owner/user in the US, so it is not surprising that Simplify3D has no configuration file for the Atom2. What I did was set up a Custom printer using the standard Atom2 parameters (bed type, build space dimensions, etc.) and then added the slicing parameters I had been using in Kisslicer and Craftware.

This is not difficult to do, but if you decide to get Simplify3D I would be happy to post my Simplify3D settings file which you could import into your copy of the software. They call it a Factory File.

徐凡
2015-07-30 11:41:14

Thanks for your reply. As you said, it is not cheap!! HA HA So, i want to make sure it is going to working after i buy it. Thank you and have a good night.

原文網址 Hung Sam
2015-07-26 13:31:10

請問各位大大能否幫忙解析第一次列印出現問題影片所示，kisslicer參數也有照寶典上設定已經試了3～5次看起來都是這個現象，只差別printer-hardware z offset[mm]在0.5～0.7［以為設太低］，已先停止了，想請問這是機構or參數問題？？
｛但ㄧ開始的300height列印沒問題，規格在誤差內，異常發生前後列印都有執行autohome、autolevel 、也有檢查過進料也是正常的｝