ATOM 3D Printer Group 造訪社團 » ATOM 2.5

給各位同時擁有ATOM2.5EX 雷射模組的朋友一個小巧思，可以利用ATOM2.0或2.5原來的開關位置，去買一個開關幫雷射模組安裝一個開關，免得不用的時候雷射模組風扇還在那邊轉降低壽命！
我個人是連同雷射模組的控制板電源都斷，不然那天使用雷射時卻忘了開風扇就糗了～

不好意思⋯強迫症爆發，整線整超久⋯
ATOM2.5EX 加 雷射模組！塞好塞滿～

請問ATOM2.5鐵氟龍管末端的斜切有無特殊工具或方法呢？

感謝早上各位前輩的指點，atom2.5ex已經可以開始列印了

左邊灰色是之前的印表機印的，右邊是今天晚上剛出爐的作品

發現嘴巴的部分往x軸的方向偏移了
請問這個是皮帶太緊或太鬆導致的嗎？

新手發問：
昨天晚上剛組好Atom2.5EX
跑過run auto level後
上官網抓了 300height.gcode的檔案
結果每次列印都出現這種狀況

想請問這是那邊出狀況了

玻璃和鐵板上都被刮了好幾道刮痕，相當心痛啊 囧

感謝ATOM2.5ex很給力組合好馬上開工就能趕案子!! 分件列印也難不倒2.5 !! 假組裝模型就準準準了，可憐的2.5目前都沒什麼機會關機繼續拚案子!!!

分享奇實數位文創與插畫家繪本的腳色實體化案例，這邊大致上把創作繪圖與分件列印到上色紀錄了一下，奇實數位文創很願意與各種台灣藝術與創意工作者合作，本次分享與台灣插畫家合作的繪本腳色立體化，目前在展覽有興趣的朋友可以來看看，支持台灣的藝術家們!!

So I had an accident with my Atom printer.
I've only recently brought it, when the delivery man arrived my sister was at home.
She said he was very impatient and basically left the printer on the side rather than on the bottom and left, forcing my sister to unpack and place the printer upward on the table we arranged for it.
for few days some prints succeeded while others failed, I signed at off as being novice, maybe too much or too little glew in addition to wrong print settings as well as objects too small or too large.
Until today I worked with cura version 15.04.6, printer model by the way is the Atom 2.5 EX.
Today I decided to try using simplify3D, the only setting I changed was adding a brim to hold the object I wanted to print.
Thats when everything went wrong, the printing head went down and toward me few minutes after beggining to print, resulting in too much plastic flowing from the nuzzle and one of the holding bars at the back disconnecting from the magnet on the heatend.
After stopping, reattaching the bar, clearing the bed and selecting home I went to recallibrate the printer.
Again the same bar disconnected, this time the nuzzle also scratched the bed and my only option was to shut it down and reboot.
A second and third callibration attempts went well except for the noise coming from the back belt, which also not moving well.
I made sure the work area is clean so nothing would reach the belt.
After contacting the manufacturer I was instructed to check the belts and the M5 bolts as its the likely source of the problem.
When checking I found out that the bolt on the back leg was bent, my guess is that this damage happened when the delivery arrived because of how the delivery man placed the printer.
It is not Tesla's fault as I have no doubt they did perfect work to gurantee high quality of the machine, and answering to me at midnight (local time) only show how much dedication they have toward their costumers.
It is a shame to know that some transportation companies just don't value the companies they work with, the product they ship and the end costumer, who in this case spent alot of hard earnd money.
My only hope is that from now on Tesla will not work with that particular shipping company and I guess it will be close to a week before my printer is back online.

翻譯年糕

請教前輩 ??
如有大型商品要印製
會使用什麼軟體切割分段印

本身使用sw和creo
目前接觸是atom 2.5ex 和cura
新手上路感謝分享 ??

更正：全新 ATOM 2.5XE（沒空玩）-售-
以前貼ATOM 2.5（我以為 ATOM 2.5XE 都一樣）
後來『陳維德』先生問我，我才知道2.5是單進料？
更正一下，是雙進料（預加熱底盤...）
反正我也不是有很多實踐研究這方面
當初看官方介紹影片，好奇購買
（充滿幻想...3D列印.還可以自己加購買雷射頭.還看到有人改成雕刻機...）
自己卻沒時間

因為，自己事業繁忙，放著也不是辦法，故賣給有緣人
目前機台狀態說明：
參加『 ATOM 2.5 早鳥活動』時購買
收到後，直到過年才組裝好（100% 未通電）
全部沒動過！至於是否組裝好，要購買者自己看
我是『看圖組裝』，所有原廠東西都齊全
想過年後，再來玩.....
眼見都6月中了（還是沒時間）所以：決定賣！

地點及方式：
1. 台中市區自取
2. 非台中市區暫不建議寄送(除非自取)

若有意者請聯繫：hong01685168@gmail.com 謝謝！
---------------------------

[疑問]
各位版上大大好，小弟目前使用Cura 15.04.6切片軟體來產生gcode，可是cura 15只有兩種support可以選擇。於是，想說用cura 2.6來切片試試看，但是產生的gcode，在ATOM2.5 EX 的機器上執行，一點反應都沒有。我已經將cura 15 machine settings，還有start.gcode，end.gcode都抄到cura 2.6。可是機器一樣沒有反應，請教一下各位大大，有什麼方法可以解決這問呢? 謝謝各位。。