• 3D列印服務
  • COSPLAY 3D 建模
  • #maker+t=market
  • 1
  • 2
  • 3

ATOM 3D Printer Group 造訪社團 » Neutron 話題

原文網址 Yohann Toutain
2019-01-21 05:26:52

First printing tests on my Neutron. The result is... not fantastic...

翻譯年糕

邢鳳言
2019-01-21 07:29:03

it should be better after tuned

Yohann Toutain
2019-01-21 07:49:45

Hum i think i will have good times solving my scale problems...

Malak Ghorghi
2019-01-21 13:18:56

Wow its amazing but you need a fan to cool down the filament. It’s all over heat


原文網址 Yohann Toutain
2019-01-12 06:18:24

Hello Everyone.

I need your help about my project of Neutron 3d printer.
The configuration of my mother board in Marlin is:RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan). Here is my problem: i can't move the X and Y axis when i go to Prepare -> Auto Home, only the Z axis move. When i go to Prepare -> Move axis and choose a length for the X or Y axis, only the Z axis move. What i have doing wrong??

翻譯年糕

Yohann Toutain
2019-01-19 07:18:39

I have found the problem, my Ramps was defective...


原文網址 Yohann Toutain
2018-12-29 02:38:34

The building of the Neutron 3d printer progress slowly but surely...

翻譯年糕

ATOM 3D Printers
2018-12-29 05:17:45

Nice and beautiful!

Genu Wu
2018-12-29 12:02:36

almost done!

Tommy Liu
2018-12-29 14:58:02

?


原文網址 Yohann Toutain
2018-12-07 01:55:01

ATOM_Neutron.01 Ready... Not yet, but soon...

翻譯年糕


原文網址 Yohann Toutain
2018-12-06 03:13:42

Neutron firmware loaded in the Arduino Mega.

翻譯年糕


原文網址 Yohann Toutain
2018-12-06 03:10:56

All 3d printed parts of the Neutron are ready. PLA used: 422 gr. Total print time: 126 hours.

翻譯年糕

سجاد حسن الجمالي
2018-12-06 11:22:57

I'll started with proton. I will give u tge result after end


原文網址 Yohann Toutain
2018-12-01 03:43:12

I need some help. Anyone know where to connect the X Y Z and the head endstops on the Ramps 1.4 for the Neutron delta sprinter?

翻譯年糕


原文網址 Yohann Toutain
2018-11-30 19:16:04

Hi! Base of the Neutron printer ready!

翻譯年糕


原文網址 Yohann Toutain
2018-11-28 20:08:39

Hello and thank you for the invitation. I'm planning to do the Neutron delta printer. Here is the first piece!

翻譯年糕


原文網址 Loïc Hannequin
2018-10-04 18:52:27

Hi everyone ! I plan to build an Atom Neutron. I start to seek hardware but finding 12mm hollow guiding rod is a pain plus it have to be thread (M8)... If someone have an address to buy this stuff I will be grateful to know it ! :)

翻譯年糕

Hawke ChienSheng Liu
2018-10-04 19:40:02

It is a custom parts. Find a factory, fabricate some.


 

全不選 主題相關關鍵字