ATOM 3D Printer Group 造訪社團

原文網址 Ricky Cheung
2019-03-26 17:50:21

Predator cigarette and mobile phone holder case is done ?

翻譯年糕

原文網址 Birk Binnard
2019-03-26 00:30:59

TwistedFlutes7

STL file and more info is here:

https://www.thingiverse.com/thing:3516925

翻譯年糕

原文網址 邢鳳言
2019-03-25 17:09:10

調Proton的Y軸調到聯軸器都滑牙了, 於是先畫一個印出來應急, 結果發現用自己印的聯軸器就不用調了, Y軸很準呀...
圖檔在此: https://www.thingiverse.com/thing:3573962
# 炒冷凍飯Proton
# 餘料裝起來清理空間了
 # ShaftCoupler

Vincent Liu
2019-03-26 09:19:08

看您的影片上馬達目前沒動，如果原本是同時動的，要觀察看看有可能是上下馬達不同步造成的。

原文網址 Jerry Shan
2019-03-23 18:53:26

請教一個問題，我的ATOM 2.5EX印一個直徑15cm的物件，大約印了2-3mm就會發生磁鐵桿脫落的問題，嘗試水平轉90度+放慢速度也是一樣，請問是哪裡的問題?謝謝大家!

李大淳
2019-03-23 19:29:46

查一下切片軟體的路徑

陳維德
2019-03-23 19:33:51

CURA 15.4.6 版可能會是外掛的問題,去看看有沒啟有什麼外掛,有就是刪了,沒看到可刪除的XX,視窗放最大會看到

Jerry Shan
2019-03-23 19:37:45

我的0.3層厚列印面會有溢料的情形，開0.2層厚比較不會，請問該如何調整？

羅廣哲
2019-03-25 18:03:58

可以開Brim到5mm寬, 以防止邊角翹起, 噴頭不會撞到列印件! 或四個邊角加老鼠耳朵, 也有相同效果!

羅廣哲
2019-03-25 18:04:29

加Brim到5mm寬!

陳逸文
2019-03-27 23:49:15

請問是只有印該檔案才會發生的嗎？

原文網址 Todd Whetstone
2019-03-23 14:48:19

When trying to auto level my Neutron, this is what I get. The effector wont go all the down to the build plate, it stays some where around 140-150mm above the plate, goes through all the motion of leveling, but does nothing. I increased my build height from 200mm to 220mm, but I'm not sure where to change it in the firmware. Any help would be very much appreciated. I'm excited to get printing.

翻譯年糕

James Lin
2019-03-23 14:58:59

這台好像沒這麼高~

Yohann Toutain
2019-03-23 18:27:10

First use the height by default (225 if i remember), then in your Marlin firmware, you should have this line: # define DEFAULT_AXIS_STEPS_PER_UNIT, increase the values on X, Y and Z until you can do the auto leveling properly. Then make some XYZ cubes test to verify if it respect the good tolerances and adjust if necessary. If you have problems of under or over extrusion you will have to do the same for the E.

Malak Ghorghi
2019-03-23 19:30:26

Hugo Lopez Uria here a nice conversation I saw maybe to be useful for you.

邢鳳言
2019-03-25 04:33:43

# define DELTA_HEIGHT 230 // get this value from auto calibrate
in my case, to make sure the bed would be probable.

原文網址 Todd Whetstone
2019-03-23 12:50:51

Finishing up on my Neutron and I was wondering if anyone is using Simplify3d? What profile do I use and if someone has a profile to share with me? Any help would be much appreciated.

翻譯年糕