Anycubic Photon Printer Owners 造訪社團 » LASS

So I had some cracks from on the yellow, plexiglass faceplate. Nothing that will let light in but has anyone else had this?

翻譯年糕

I'm looking at buying a magnetic stirrer, and would modify this item to allow the stirrer to spin underneath (or just use a large mason jar). For those that have a magnetic stirrer, would this defeat the purpose of it? https://www.amazon.com/LOCK-HPL933BT-Pickle-Container/dp/B06WD1F7HD/ref=sr_1_13?dchild=1&keywords=glass+container+with+strainer&qid=1584564100&sr=8-13&swrs=8DEFA1015DD7E74785167E39F51EC8B0 翻譯年糕

Here's the latest on my workbench. This is my Fallout Nuka Cola machine printed on my "classic" Photon. Elgoo gray, .05 layers, 9 s normal exposure.

I've finished most the painting (just need to touch up the bottoms of the Nuka Cola bottles). This is the last mock-up for the base. I may still change some little detail or other, but I think this is pretty close to what I had in mind.

The machine is a re-mix 3D print file I found on Thingiverse. I made a fair number of changes to it, but still, I wouldn't claim it as an "original" design. I added the coin-op control details, modified the cooler box and door, and hollowed the entire thing to make it easier to print.

The bottles are my own original design, though. I tried to use another file that I found online, but it was created to print cos-play prop bottles, and after futzing around with that, it was just easier to make my own bottle design that I knew would print reliably.

The catus is from a Pegasus Models set of injection molded cactus plants. It helps balance the composition and adds a southwest desert feel.

I sketched up the layout and played around with it a bit before I made this foundation piece from sheet and strip styrene. It'll get glued down to a piece of foam to give some presence and height to the final display. Lots more work to do on the base, but I think this little project is coming along nicely.

Happy modeling!

這是我的工作台上的最新訊息. 這是我在我的"經典"光子上列印的核可樂機. Elgo gray 05層, 9 s正常曝光.

我完成了大部分繪畫(只需要摸一下nuka可樂瓶的底部). 這是基地的最後一個模型. 我可能仍然會改變一些小細節, 但我認為這和我的想法相當接近.

這台機器是我在thingiverse上發現的3 d列印檔案. 我對它做了相當多的修改, 但仍然, 我不會聲稱它是"原創"設計. 我新增了硬幣操作控制細節, 修改了冷卻器盒和門, 把整件都空洞, 讓列印更容易列印.

瓶子是我自己的原創設計. 我嘗試使用我在網上找到的另一個檔案, 但它是為了列印cos-play道具瓶子而創建的, 然後用它打亂後, 我知道可以可靠列印的瓶子設計更簡單.

Catus是來自一套飛馬座噴射模型的仙人掌植物. 它有助於平衡成分, 增加西南沙漠的感覺.

在我用床單和脫衣櫃和脫衣舞的底片之前, 我繪制了佈局並玩弄了一下. 它會粘在一塊泡沫上, 讓最終展示一些存在和高度. 基地還有很多工作要做, 但我認為這個小項目進展順利.

快樂的模特!

· 查看原文 · 為此翻譯評分

This is good therapy before the craziness reasumes in two weeks when I have to teach my classes online...

翻譯年糕

From prototype to finished model reproducible and scalable!
Including the original model of the vehicle this represents 4 years of work. Lots of failures....lots of starts and stops. But any day now it will be ready for the boxes.
1/48th scale Boeing x20 Dyna-Soar in ABS resin printed on the Anycubic Photon Classic and S and the Elegoo Mars resin printer. Time to print complete model 98 hours on one printer without print failure.

翻譯年糕

Print bed level new issue:

New issue ive been experiencing, Been printing really well the past few days but now nothing print. I get maybe 1 layer stuck to the bottom of the bed then nothing.

Noticing: print bed does not hit glass anymore when attempting to bed level. I can cant the bed forward or backward with a touch and it wont go down any further. Could this be the issue?

翻譯年糕

Classic Photon with Simon Jackson's z-rail upgrade, 50 microns, 8xAA, Elegoo grey. Scale 1/4.

翻譯年糕

Anyone tried the ESUN water washable transparent resin? I done on Anycubic Photon: gone very well, I washed and postcured (like somewhere recommended for crystal resins) on UV device under water (a glass). After print result was great, after wash also, after 10min. postcuring was ok, but later, after drying with just compressed air everything was covered by a white dust. (Someone mind theback of some Shapeways ultra frost prints?The same). If you polish the print it gone away.... but I have small lens... hard to be polished. Any know why? Any advice? Thanks.

翻譯年糕

I have some ameralabs clear resin left from a long time and i couldn't get any print out of It. now, as you can see from this crystals that i left out in the sun, it's clearly still working. Does anyone know any good parameters to print with this semi spoiled leftovers?
Ps: did you know that curing resin gets really hot really fast? Especially if It Is a Thin layer more than a full glass. I Guess because It cures faster and the reaction cause the warm up

翻譯年糕

I got a (classic) photon over the holiday sales. It is one of the newer fauxtons...

It was working just fine, printing minis, no issues and now it isn't reading any of the sliced files. It shows the names on the lcd screen but no image of the print and trying to print says file error.

I have tried several other USB sticks, I have tried old files that I just had work. No luck.

I updated the firmware with no problems so I know the USB does work. But this didn't fix the problem. Any ideas form the hive mind?

翻譯年糕