Anycubic Photon Printer Owners 造訪社團 » LCD

原文網址 Timothy White
2019-06-27 19:31:32

Righto, So I replaced my LCD today, checked with UV detection, ran a test print, all good, ran a print of 4 jeeps, printed a few of the layers of the test print (which is on a different stick) over and over again. Now when I use the UV detection in the tools section I get an image of the layer from the test print. Any thoughts?

翻譯年糕

George Bulte
2019-06-27 19:34:01

Timothy White
2019-06-27 19:37:15

Timothy White
2019-06-27 19:38:04

George Bulte
2019-06-29 20:00:14

原文網址 Joe Foulkes
2019-06-27 16:48:14

So I just replaced the motherboard and LCD on my photon and now I have the half screen issue. Tried power cycling the machine, updating firmware, using different USB's and reseating LCD cable. Any other suggestions?

翻譯年糕

Andrey Sabrev
2019-06-27 17:35:18

Joe Foulkes
2019-06-27 17:36:00

Andrey Sabrev
2019-06-27 17:37:14

Joe Foulkes
2019-06-27 17:37:59

Andrey Sabrev
2019-06-27 17:53:26

Andrey Sabrev
2019-06-27 18:09:21

Andrey Sabrev
2019-06-27 18:11:38

Joe Foulkes
2019-06-27 18:18:21

Andrey Sabrev
2019-06-27 20:25:33

Joe Foulkes
2019-06-27 20:26:02

Andrey Sabrev
2019-06-27 20:27:39

Andrey Sabrev
2019-06-27 20:30:14

Joe Foulkes
2019-06-27 20:34:25

Andrey Sabrev
2019-06-27 20:41:58

Joe Foulkes
2019-06-27 20:44:44

Andrey Sabrev
2019-06-27 20:48:35

Muhammad Zulkhairol Yacob
2019-06-28 03:23:41

Joe Foulkes
2019-06-28 03:38:39

Muhammad Zulkhairol Yacob
2019-06-28 03:39:32

Joe Foulkes
2019-06-28 03:40:07

Adam Musgrove
2019-07-18 10:35:15

Joe Foulkes
2019-07-18 13:46:04

原文網址 Kittye Parker
2019-06-27 09:42:43

Help! We have a Photon and just got an Epax LCD replacement and we got it installed. The light is shining through, but it's not actually responding to the shapes in the test. So we put the rectangle, and the whole screen still lights up. Any ideas what we're doing wrong?

Edit: We've made sure the connections are secure, we checked to make sure there wasn't a backlight covering (although we did remove the silvery backing based on what we read from other posts) , we tried updating the firmware and then reverting back to the original firmware. We are at a total loss! Did we get a bad screen? Or is something else jacked up?

翻譯年糕

Jean-François Meloche
2019-06-27 19:42:29

Kittye Parker
2019-06-28 03:42:30

Marvel Mendoza
2019-07-09 06:07:40

Kittye Parker
2019-07-09 23:09:20

原文網址 Nikko Chua
2019-06-27 02:02:51

anyone know how i can get this tacky residue off my lcd bezel?

翻譯年糕

Marco Acquaioli
2019-06-27 02:07:36

Nikko Chua
2019-06-27 02:10:01

Marco Acquaioli
2019-06-27 02:11:24

Ronan Tully
2019-06-27 02:14:29

Marco Acquaioli
2019-06-27 02:38:53

Bob Deblier
2019-06-27 02:42:34

Nikko Chua
2019-06-27 02:45:56

Nikko Chua
2019-06-27 02:47:18

Lestat De Lioncourt
2019-06-27 02:53:47

Nikko Chua
2019-06-27 02:58:25

Susan Sioux Mercer
2019-06-27 04:19:10

Susan Sioux Mercer
2019-06-27 04:19:43

Nikko Chua
2019-06-27 04:20:31

George Bulte
2019-06-27 04:23:49

Stephen Eaton
2019-06-27 23:38:54

原文網址 Alan Castell
2019-06-26 05:19:22

Here is what I consider the main tips from a newer owner of a Photon but one who has been 3D printing for a few years now.

The FEP is very important in having success with this printer.

Kudos to Anycubic for including 2 EXTRA FEP sheets with each printer. This on top of the one that is installed.

Now, on to some tips.

As a newer user, I didn't really understand all the finer details of the Photon. I jumped in and wanted to print.

Of course things didn't work perfectly and I found myself cleaning the vat more than once. Taking it out only to have a drop of resin hit the LCD screen, cleaning it, then forgetting to clean UNDER the FEP so then bits of resin cure UNDER and on the LCD screen itself.

Once I got all those issues out of the way, I found out that there was a small leak in the FEP, so I was going to have to replace it.

Follow the video from Anycubic. Works perfectly. Remember that there are TWO protective sheets, remove them both and handle the edges as you will be cutting that off. Should be tight like a snare drum. This was a bit tedious but not hard at all. I am glad I did it, fixed up some of my random failed prints.

If you get some resin on the LCD, wipe it off, and if you unfortunately have resin on the screen and it gets cured to it, this worked for me. Use the plastic scraper and you can apply a decent amount of force to scrape it off. Approach it from a different angle if you need to get under it. Mine is perfect after this incident. I now have some optico glasses cleaner packages that I use and throw away to clean it if I need.

Follow the suggested times for resin taken from the spreadsheet that is easily searchable. Adjust if you need, remembering that just like FDM printing, it is all about the first layer.

On that note, a lot of people don't realize that "HOME" is a physically set point. So when you are doing the 0 level make sure to home the print bed first. THEN make your adjustments using a piece of paper. Lock down the grub screw when you have your hand pushing on both sides. I actually pull the paper back enough so that is barely shows the inside top edge of the LCD. I find that help to make sure that the bed is straight as well as you have something to align to. Check after you tighten the screw, then back out and 0 level and say "yes" to save it. Remember that "HOME" doesn't take it to the 0 level you set. I made this mistake and kept thinking it wasn't saving.

Now that I have a bit of time on the printer, I a

m so impressed with the quality for the price.

Look forward to seeing more and learning off this group.

翻譯年糕

原文網址 Benny Lu
2019-06-26 03:06:10

If you're in the US and have not tried out Dragon Resin, It is now available in the states! There are 20 colors to choose from and there are even metallic colors. https://3dprinteruniverse.com/products/dragon-resin-fast-cure-for-msla-lcd-dlp-led-3d-printer
Metallic below:
https://3dprinteruniverse.com/products/dragon-resin-fast-cure-exotic-metalshine-for-msla-lcd-dlp-led-3d-printers 翻譯年糕

原文網址 Olli-Pekka Salli
2019-06-26 02:12:18

Hi. Please help a little.
I print test pattern ( https://github.com/altLab/photon-resin-calibration ) with Photocentric flexible resin ( https://photocentricgroup.com/uv-lcd-resin/ ). In center of print printing leaves very odd area, with no image at all (Gray print).
Also I test Wanhao STD Yellow resin, and there was none that kind of "spot". It works normally (Yellow print).
Any idea what was happening? 翻譯年糕

Troy Tepes
2019-06-26 02:16:03

Olli-Pekka Salli
2019-06-26 02:19:20

Olli-Pekka Salli
2019-06-26 02:19:53

Troy Tepes
2019-06-26 02:20:32

Olli-Pekka Salli
2019-06-26 02:27:42

Ronan Tully
2019-06-26 02:59:40

Olli-Pekka Salli
2019-06-26 03:19:11

Ronan Tully
2019-06-26 03:19:54

Olli-Pekka Salli
2019-06-26 03:21:53

Olli-Pekka Salli
2019-06-26 03:25:02

原文網址 Çağrı Aydoğan
2019-06-25 22:22:39

i post this by request of Vinicius Silva

This is Creality LD-001 resin printer recently we bought for resin testing. it has some great features.

-wifi (you enter ip on your browser and you can upload and start printer through you browser)

-lcd changing is very easy. there is metal frame over lcd with 4 screws and on the left side of the printer there is cover to remove cable. i realy liked it how easy they made changing lcd

-it uses slicer called 3d creator slicer. i didnt use much but it looks terrible.

-after you slice the file when you click print it asks you bottom exposure time and normal exposure time. in some cases this is good

-when you place the vat over the screen it dosent have place to fit so you need to check if it fits good or not. (they need to fix this)

-build plate has mat surface glass. i dont know if its good or not yet. i made only one print and it was very easy to remove comparing to photon. it gives idea that wont hold big prints. i will print something big and see if its good or not

-leveling was easy. no need to adjust any z=0. just home the z axis and tighten for screws

-so far only one print made and result was good.

-3.5 inch screen seems better than photon.

-it uses rasperry pi board

翻譯年糕

Juan Carlos Ramirez
2019-06-25 22:29:09

Jarrod Smith
2019-06-25 22:36:44

Çağrı Aydoğan
2019-06-25 22:38:23

Çağrı Aydoğan
2019-06-25 22:38:55

Milton Maxson
2019-06-25 22:40:02

Jarrod Smith
2019-06-25 22:43:30

Milton Maxson
2019-06-25 22:44:11

Jarrod Smith
2019-06-25 22:44:40

Rick Denny
2019-06-25 22:45:13

Çağrı Aydoğan
2019-06-25 22:45:36

Vinicius Silva
2019-06-25 22:47:06

Milton Maxson
2019-06-25 22:50:15

Milton Maxson
2019-06-25 22:51:14

Stephen Ross
2019-06-25 22:54:01

Jarrod Smith
2019-06-25 22:54:18

Çağrı Aydoğan
2019-06-25 23:01:10

Milton Maxson
2019-06-25 23:01:40

Giannis Andronkidis
2019-06-25 23:36:37

Andrey Sabrev
2019-06-25 23:54:50

Çağrı Aydoğan
2019-06-25 23:55:39

Ricardo Ribeiro
2019-06-25 23:55:53

Çağrı Aydoğan
2019-06-26 00:01:15

Çağrı Aydoğan
2019-06-26 00:01:44

Daniel Velarde Kübber
2019-06-26 00:14:32

Ricardo Ribeiro
2019-06-26 00:34:24

Philippe Maegerman
2019-06-26 00:57:36

Brent Stevens
2019-06-26 01:54:06

Çağrı Aydoğan
2019-06-26 01:58:40

Eric Wilfreesboro
2019-06-26 02:12:20

Çağrı Aydoğan
2019-06-26 02:33:11

Brent Stevens
2019-06-26 02:44:24

Vinicius Silva
2019-06-26 02:55:38

Brent Stevens
2019-06-26 03:12:59

Christopher Botha
2019-06-26 04:08:59

Christopher Botha
2019-06-26 04:13:46

Christopher Botha
2019-06-26 04:17:17

Çağrı Aydoğan
2019-06-26 04:45:28

Michael Ohl
2019-06-26 04:46:22

Çağrı Aydoğan
2019-06-26 04:48:13

Stuart Radmore
2019-06-26 04:56:37

Ron Luttrull
2019-06-26 05:16:15

Benny Lu
2019-06-26 06:46:02

Vinicius Silva
2019-06-26 06:46:30

Vinicius Silva
2019-06-26 11:43:27

Andrew Gott
2019-06-26 12:50:50

Çağrı Aydoğan
2019-06-26 22:45:21

Gary Houser
2019-06-28 02:44:24

Çağrı Aydoğan
2019-06-28 02:45:55

Gary Houser
2019-06-28 02:46:43

原文網址 Dillon Olney
2019-06-25 07:23:33

Printer has been giving me hell, replaced the lcd screen and the protective screen below, releveled using paper method, replaced fep film and yet..... at .05 I get these weird lines!

翻譯年糕