Anycubic Photon Printer Owners 造訪社團 » LCD

原文網址 Danny Tix
2019-03-05 06:06:03

My photon was at the point where every single print would fail with a USB read error, even on new drives of a known-good model. I finally got around to disassembling the unit and noticed that my USB port was off-center and its shielding was touching the photon's outer case. Some quick electrical tape around the case opening and I'm back to printing*.

*During my first print after taping, half of the LCD went out; but this was resolved with a firmware update. Is there a connection? Who knows...

While I had the case open, I noticed that the USB port is pretty close to what I think is the power regulator for the UV light source. I didn't get a good look at the component, but there are some inductors on it right next to the USB port and I expect it's putting out some interference. I plan to do some proper testing and to maybe add shielding when I get the time, but I'm posting here now to gauge others' experiences and to see if anyone else sees an improvement from the tape. Does the EMF + grounding theory sound plausible to anyone else?

翻譯年糕

Darren Pawluk
2019-03-05 07:10:12

Chayanin Somton
2019-03-05 16:42:37

Darren Pawluk
2019-03-05 21:27:15

Danny Tix
2019-03-06 01:09:16

Darren Pawluk
2019-03-06 02:46:44

Danny Tix
2019-03-06 02:56:51

Darren Pawluk
2019-03-06 03:51:28

原文網址 Vinicius Silva
2019-03-04 21:09:12

Turns out photon does come light masked from factory
(.lcdimg)
file firmware is the mask file Turns out photon does come light masked from factory
(.lcdimg)
file firmware is the mask file 翻譯年糕

Vinicius Silva
2019-03-04 21:12:51

Sterling Osment
2019-03-04 21:15:41

Daniel Ignacio Perez
2019-03-04 21:16:58

Sterling Osment
2019-03-04 21:17:09

Vinicius Silva
2019-03-04 22:00:42

Vinicius Silva
2019-03-04 22:01:43

Robert Silvers
2019-03-04 22:34:39

Sen Kun
2019-03-04 22:40:22

Chris Crute
2019-03-04 23:10:27

Bob Leschyna
2019-03-04 23:22:08

Vinicius Silva
2019-03-04 23:22:12

Vinicius Silva
2019-03-04 23:24:25

Vinicius Silva
2019-03-04 23:25:34

Nuno Lega
2019-03-05 05:46:06

Jawad Abuasabeh
2019-03-05 07:30:28

Robert Silvers
2019-03-07 02:04:36

Dustin Scott
2019-03-07 02:24:11

Maurice Sand
2019-03-14 02:18:17

Péter Farsang
2019-10-08 02:52:55

Maurice Sand
2019-10-08 19:15:47

Péter Farsang
2019-10-08 19:30:23

Maurice Sand
2019-10-08 19:40:29

Maurice Sand
2019-10-18 19:27:49

原文網址 Sean Poeschl
2019-03-04 11:30:58

Help!

Running into an issue suddenly that sounds somewhat like something in the known issues FAQ: "Z motor stops moving mid-print, LCD keeps exposing resin, no error message, stopping print and moving Z via menu works."

Basically I start any print and the Z axis works normally. When it gets to layer 2 or 3, the Z axis just stops functioning and the LCD keeps on displaying layers as it normally would without any movement. Generally speaking, the build plate is still submerged in the resin, where the last successful layer was prior to Z movement stopping. This happens even on files that I know have been "good slices"(as in, I've printed many times before).

If I cancel the print, Tools>Move Z will not respond. If I power cycle the printer, I can then use Tools>Move Z to move the plate up.

Things I've tried so far:

-Updating firmware to newest
-Eeprom reset
-Reformatting USB (using my own USB)
-Using a different USB
-Reslicing files

Anyone run into something like this and found a way to fix? I also sent an email to Anycubic but figured I'd check here while I wait. Thank you, Photonsters!

翻譯年糕

Stefan Giudici
2019-03-04 11:44:09

Sean Poeschl
2019-03-04 11:47:22

Kaile Riser
2019-03-04 12:03:32

Sean Poeschl
2019-03-04 12:26:16

Sen Kun
2019-03-04 17:29:54

Sean Poeschl
2019-03-04 22:53:50

Sen Kun
2019-03-04 22:55:37

Sean Poeschl
2019-03-04 23:04:05

Sen Kun
2019-03-04 23:05:23

Sean Poeschl
2019-03-04 23:06:00

Sean Poeschl
2019-03-04 23:10:50

Sean Poeschl
2019-03-05 03:15:46

Sean Poeschl
2019-03-05 03:16:22

Sen Kun
2019-03-05 03:18:02

Sean Poeschl
2019-03-05 03:41:51

Sean Poeschl
2019-03-05 04:00:20

Sen Kun
2019-03-05 04:14:19

Sean Poeschl
2019-03-05 04:19:03

Sean Poeschl
2019-03-05 21:19:02

Sean Poeschl
2019-03-05 22:37:44

Sen Kun
2019-03-05 22:57:29

原文網址 Vinicius Silva
2019-03-04 10:54:01

Email with sugestions to Anycubic and reply from James
UPDATE:
I just found out that the .lcdimg on the photon official firmware update files is actually a Mask File for the light distribution.

I asked Amy Liao to talk to R&D and ask them for a tool to build these .lcdimg files so people with custom light mods can build a propper mask for their modded photons

That or share the source binary so we can at Photonsters make that tool. I already have the solution working with a ESP, easy to make to evaluate the light distribution

翻譯年糕

Richard Thomas
2019-03-04 18:02:44

Sen Kun
2019-03-04 18:29:24

Susan Sioux Mercer
2019-03-04 18:45:48

Vinicius Silva
2019-03-04 20:53:35

Vinicius Silva
2019-03-04 20:55:57

Vinicius Silva
2019-03-04 21:01:58

Sen Kun
2019-03-05 05:28:37

Sen Kun
2019-03-06 04:18:39

原文網址 Robert Silvers
2019-03-04 01:25:27

So I just saw this offer. I tried the Bio-red and it is 8 second exposures on the Photon and twice as strong as most other resins (but not as strong as Blu). It is without a doubt my favorite resin now for solid colors. Only in red or yellow for now.

Saw it here but it is from Feb 15th so no idea if they are still doing it. It may be over, not sure - don't be disappointed if it is over. Contact them to find out. Maybe make the case that you are experienced and post a lot of what you learn to help others and see if they will still do it: https://www.facebook.com/epax3d/

"William Intservo
February 15 at 7:46 PM
We are giving away some eSUN newly made PLA based Resins for LCD/DLP printers. 500ml bottle. USA only. You must be an experienced user who can print with the resin and share your experience. This PLA based resin works perfectly with our carefully crafted EPAX X1 5.5 inch printer. It also works fine with other printers such as Photon and Wanhao D7 and other LCD printers which use 405nm light wave."

Resin details can be found on

翻譯年糕

Israel Contreras
2019-03-04 01:41:50

Robert Silvers
2019-03-04 01:42:51

Christopher Botha
2019-03-04 03:34:19

Ettore Maria Bar
2019-03-04 03:50:14

Israel Contreras
2019-03-04 03:52:55

Guti Gutmann
2019-03-04 23:07:17

Robert Silvers
2019-03-04 23:08:13

Guti Gutmann
2019-03-05 05:51:49

El Ner Endem
2019-03-05 08:08:15

Matt Solomon
2019-03-05 08:19:51

Robert Silvers
2019-03-05 08:21:19

Matt Solomon
2019-03-05 08:22:50

Robert Silvers
2019-03-05 08:23:19

Matt Solomon
2019-03-05 08:24:22

原文網址 Timothy Purcell
2019-03-03 08:47:15

So my LCD has a fingerprint or two on the underside of the screen, not on the top. Is this fixable and does it potentially harm 3D prints?

翻譯年糕

Dustin Skye
2019-03-03 10:59:35

原文網址 Kevin Delger
2019-03-03 08:21:48

I'm having an issue trying to flash the new firmware (my printer squishes the first 6mm or so into about 1mm). I've downloaded the zip, extracted it onto a USB leaving the three relevant files as the only files on the stick in the main directory. When I plug the stick in and turn on the printer I don't hear any "di di" sound to tell me the printer is automatically recognizing the files. When I go to print the files I get "Unknown File Type" as a message on 255.lcdimg. The .bin file seems to run successfully. If I try to print update.LCD the printer says "firmware update now!" with the option to hit "Yes", but the printer immediately restarts and then gives me blank spaces in the print menu and Memory error code M_11000. I've tried the same process on two other new FAT32 formatted USBs.

翻譯年糕

原文網址 Robert Silvers
2019-03-03 04:42:11

Please read my article on the difference between DLP and LCD.

翻譯年糕

Kevin Reynolds
2019-03-03 05:02:22

Douglas Guerra Dos Santos
2019-03-03 05:03:16

Pietro Malaguti Abbate
2019-03-03 05:21:49

Josh Norris
2019-03-03 06:24:02

David Wang Honey
2019-03-03 06:37:03

Pietro Malaguti Abbate
2019-03-03 07:09:45

Robert Silvers
2019-03-03 07:11:20

Robert Silvers
2019-03-03 07:15:55

Jack Sweek
2019-03-03 07:45:12

Xavier Cebeira
2019-03-03 07:46:06

Robert Silvers
2019-03-03 07:52:00

Robert Silvers
2019-03-03 07:58:52

Robert Silvers
2019-03-03 07:59:19

Todd Jones
2019-03-03 08:32:21

Marcus Como
2019-03-03 13:22:57

John Haywood
2019-03-03 23:43:21

Xavier Cebeira
2019-03-03 23:47:56

John Haywood
2019-03-03 23:50:53

Xavier Cebeira
2019-03-03 23:59:11

Robert Silvers
2019-03-04 00:12:52

John Haywood
2019-03-04 00:18:11

Peter Ede
2019-03-04 08:16:59

原文網址 Bhavik Gohel
2019-03-02 21:05:33

Can we assemble 4K LCD in photon?
For Jewellery printing.

翻譯年糕

Sebastian Fernandez
2019-03-02 21:09:34

Bhavik Gohel
2019-03-02 21:10:33

Juan Camilo Herrera
2019-03-02 21:11:05

Bhavik Gohel
2019-03-02 21:11:52

Sebastian Fernandez
2019-03-02 21:12:52

Bhavik Gohel
2019-03-02 21:14:08

Stuart Radmore
2019-03-02 21:20:39

Gazsó Péter
2019-03-02 21:21:12

Vinicius Silva
2019-03-02 21:36:47

Felix Nobile
2019-03-02 21:48:34

Guajolote Messias
2019-03-02 22:16:31

Alex Shpisman
2019-03-02 22:36:27

Stuart Radmore
2019-03-02 23:01:31

Stuart Radmore
2019-03-02 23:03:39

Robert Maefs
2019-03-02 23:17:44

Bhavik Gohel
2019-03-02 23:18:53

Richard Thomas
2019-03-02 23:24:02

Alex Shpisman
2019-03-02 23:30:51

Vishal Nischal
2019-03-03 00:35:11

Eric Green
2019-03-03 02:13:35

Mitchell Cooper
2019-03-03 10:52:11

Bhavik Gohel
2019-03-06 14:18:00

原文網址 Vinicius Silva
2019-03-02 20:30:55

finally nailed the supports for the heater unit, should work with both sla laser and lcd, Next i will be trying it on the photon.

the model for this heater is opensource and BOM is here ;)
will be adding the supported model to thinguiverse later today
https://www.facebook.com/permalink.php?story_fbid=10157191752823680&id=651553679