Anycubic Photon Printer Owners 造訪社團 » ABS

原文網址 Zach Harris
2019-12-27 14:10:14

Does anyone know where you can get either larger bottles of anycubic grey ABS like, or at least cases of 1L bottles?
Need to find a cheaper alternative than 1L at $40 on Amazon.

翻譯年糕

Blaze Dodd
2019-12-27 14:19:41

Rob Walker
2019-12-27 21:44:59

Chris Bondy
2019-12-27 21:51:16

原文網址 Simon Walker
2019-12-25 06:30:44

iv recently been using 2 elegoo mars along side my older photon, the mars (in my personal experience) have had nothing but problem after problem causing fail and fail and bottle after bottle of wasted resin while my photon just troopered on with no problems. so i eventually after 45 days of trying to rectify, sent them back to Amazon and got a full refund of £240 on both machines then went on Aliexpress to the Anycubic shop and bought 2 photons (original) along with 5 litres of resin with each machine (10 litres total mixed colours) for a total of only £504 delivered! shipped from poland to the UK they took only 5 days, iv waited for longer stuff locally in the UK off ebay! Absolute bargain considering there over £350 with of anycubic resin alone sitting there aswell as 2 brand new machines! :) MUCH better deal than off ebay.

翻譯年糕

Kenneth Keenaghan
2019-12-25 06:44:42

Kenneth Keenaghan
2019-12-25 06:44:53

Savio Ku
2019-12-25 07:07:29

Chris Bondy
2019-12-25 07:45:36

Rob Mayberry
2019-12-25 10:32:15

雷蒙德
2019-12-25 14:28:27

John Chrapkowski
2019-12-25 14:31:31

Игорь Лубенец
2019-12-25 15:14:45

Chris Bondy
2019-12-25 15:30:53

Lim Kim Yong
2019-12-25 17:16:12

Janne Sjöström
2019-12-25 23:32:55

Matt Farmer
2019-12-26 00:24:02

Simon Walker
2019-12-26 01:56:20

Simon Walker
2019-12-26 01:57:22

Savio Ku
2019-12-26 01:58:07

Leonard Seeney
2019-12-26 02:03:17

Arnaud Rousseau
2019-12-26 04:25:52

Arnaud Rousseau
2019-12-26 04:27:13

Sean Latto
2019-12-26 04:57:02

Jaxi Foley New
2019-12-26 05:34:19

Jackie Sparrow
2019-12-26 08:05:35

Simon Walker
2019-12-26 09:37:34

Chandler Krisowsky
2019-12-26 18:26:40

Marcin Jażdżewski
2019-12-26 18:40:02

Chandler Krisowsky
2019-12-26 18:55:18

Marcin Jażdżewski
2019-12-26 18:55:46

Chandler Krisowsky
2019-12-26 18:58:07

Marcin Jażdżewski
2019-12-26 18:58:42

Steve Kelly
2020-01-29 08:34:21

原文網址 Joe Fillion
2019-12-25 02:27:10

Alright gang, I recently got an ultrasonic cleaner for my prints and it works absolute wonders when removing resin, BUT it is noisy, extremely so. It’s upsetting my animals, it gives me a headache and it’s borderline unusable to my sensitive little ears. Has anyone had any luck in making an enclosure for it? Can I just buy those acoustic panels and save my brain from melting out of my ears? Any thoughts are appreciated and if you have a set up that works well please share.

翻譯年糕

Ryan Connary
2019-12-25 02:29:52

Joe Fillion
2019-12-25 02:33:44

Ryan Connary
2019-12-25 02:36:52

Joe Fillion
2019-12-25 02:43:49

Brett Isaacs
2019-12-25 02:48:49

Joe Fillion
2019-12-25 02:51:13

Brett Isaacs
2019-12-25 02:51:57

John Chrapkowski
2019-12-25 02:52:44

Joe Fillion
2019-12-25 02:54:39

John Chrapkowski
2019-12-25 02:55:41

Evan Boone
2019-12-25 05:25:42

Jeff Greenfield
2019-12-25 07:48:17

Alex Vee
2019-12-25 17:36:56

原文網址 David Slabbert
2019-12-24 16:29:13

I just had a weird error printing the photonster ameralabs city.

It seemed like it tried to print a few different files over to of each other, as there were 3 distinct rectangles, but all were completely flat.

Is it possible to run the print-mode.gcode too many times? I think I ran it twice accidentally

翻譯年糕

原文網址 Brannian Lee
2019-12-23 01:47:50

Starting a 12 hour print. Let’s hope this does not fail, especially late in the print. I don’t need to have wasted 200ml of resin.

Update: my dad woke me up (this print was for him). At about 4 hours in, absolutely nothing stuck to the build plate, but there is a nice thick layer on the FEP. I know it’s not a support issue, as this print doesn’t need supports. I’m thinking it may be due to that I may have had the heater too close to the printer, but I’m unsure.

2nd update: I noticed when I went to see why it failed, sometime while I was cleaning the build plate from my last print, I had angled it a few degrees. This being the problem that caused my print to fail.

翻譯年糕

Nolan Bakema
2019-12-23 01:55:37

Brannian Lee
2019-12-23 02:14:35

Vincent Vega
2019-12-23 02:34:47

Nolan Bakema
2019-12-23 03:03:51

Randy Shepherd
2019-12-23 05:44:13

Chad Elstad
2019-12-23 05:46:37

Justin Leone
2019-12-23 12:41:21

Brannian Lee
2019-12-23 12:44:44

Ben Zeeman
2019-12-23 12:50:58

Brannian Lee
2019-12-23 12:52:50

原文網址 Saitama San
2019-12-22 22:49:17

Hello all ! Another sister of battle, with a beautiful and much detailed banner, printed with my photon and used a HARZ labs black resin.

翻譯年糕

Jeremy Babcock
2019-12-22 23:07:48

Saitama San
2019-12-22 23:28:32

Benjamin Oertel
2019-12-22 23:39:07

John Rhodes
2019-12-23 10:17:50

原文網址 Vlado Turek
2019-12-22 22:37:23

In oldtime, when people couldn´t make spears yet and the nights were darker than your frightening imagination, Crystal Dragons ruled the world. They flew without fear through the world. They loved magic crystals that gave them invincible power. Until ...

Printed on Anycubic Photon with great Ameralabs AMD-3 Grey resin.

https://cults3d.com/en/3d-model/art/crystal-dragon

https://www.cgtrader.com/…/crystal-dragon-f253651d-8066-4ba…

翻譯年糕

Jeremy Babcock
2019-12-22 23:37:01

Vytenis Darulis
2019-12-28 03:22:59

原文網址 Ross Graham
2019-12-22 07:01:17

Curious, could anyone suggest why this may have happened. Both printed on same plate face-to-face as shown in last pic. One printed absolutely fine, the other, a 180 of the first has a missing beard bottom and a huge gap right through the centre of the beard and stand. But then continues printing perfectly. The other, absolutely fine.

翻譯年糕

Jarin Udom
2019-12-22 07:03:32

Jason Pedersen
2019-12-22 07:05:50

Mike Fatchett
2019-12-22 07:13:10

Ross Graham
2019-12-22 07:49:24

Mike Fatchett
2019-12-22 07:50:32

Ross Graham
2019-12-22 07:51:55

Luis RoGz
2019-12-22 18:33:14

Ross Graham
2019-12-22 21:02:37

原文網址 Daniel Chubb
2019-12-22 02:11:21

Hello folks,

I have been getting some nice prints using orange Eco resin, now I want to try some bigger things....

I know it is recommended to hollow out larger objects due to uncured resin being trapped inside, but how deeply can resin cure? At what thickness should I consider hollowing a mosel?

I tried google but I couldn't find anything. I assume there is no absolute answer, just looking for a general guideline.

Thanks for any ideas.

翻譯年糕

Stefan Giudici
2019-12-22 02:27:44

原文網址 Nicholas Smith
2019-12-21 10:48:31

Can anyone tell me why this happens ONLY at the rear of my printer? Elegoo abs like grey. 6 bottom layers at 60 sec. Others at 12 sec. Leveled plate, shook resin, ambient temp is about 28c. Every file in the rear only.

翻譯年糕