Anycubic Photon Printer Owners 造訪社團 » EX

Have had a couple failed prints lately due to lifted/curling edges. Did a thorough cleaning/releveling/general systems check, and got this one to print alright, but as you can see the front facing side is still peeling, and the back side raft layer seems far thinner in comparison.

Any suggestions as to what I may be doing wrong or could try for better results?

Photon. Anycubic elegoo grey resin. Layer height 0.5. Bottom layers 8 with 60 second exposure. Regular layers 9 seconds.

翻譯年糕

Looking for some cool support column/pillars to print on my resin printer for my miniature display case and use in game. The case only has three glass shelves and I want to print some fantasy/sci-fi pillars to hold up a sheet of plexiglass or another piece of glass on each glass shelf. Yes, I know I can buy the glass and the hanger clips but I’d rather spice it up. Any cool files floating around? I stopped unpacking minis when I realized the 3 shelves wouldn’t be enough haha.

尋找一些酷的支援欄/柱, 在我的樹脂印表機上列印, 用於我的微型顯示器, 並在遊戲中使用. 這個箱子只有三個玻璃架子, 我想列印一些幻想/科幻柱, 在每個玻璃架上都有一張玻璃或另一塊玻璃. 是的, 我知道我可以買到玻璃和衣架夾, 但我寧願加香料. 有酷的檔案漂浮嗎? 當我意識到3個架子還不夠的時候, 我就停止解開迷你, 哈哈.

· 查看原文 · 為此翻譯評分

After doing some research I cant find a good set of UV strip lights to order. I found some but I'm not sure about them
https://www.amazon.com/Onforu-Flexible-Blacklight-Non-Waterproof-Fluorescent/dp/B07D7R1PKQ/ref=sr_1_4?keywords=uv+strip+lights&qid=1583185385&s=hi&sr=1-4
翻譯年糕

After having a first week of perfect printed models with my new photon S, took a week break from printing and now I’m getting my first failed prints. First try at this file had good first layers and failed to print supports. Re did my setting, adding a full second to exposure and increasing z list of support from 5mm to 10mm. After getting to a level I could see the print, it broke away from a lot of the supports. Going to let it finish. Good learning experience with doing my own supports. Using support settings from a 3dprintingpro. A mix of light mediums and heavies. Elegoo gray 8 bottom layers 60 secs, 8.5 sec exposure. Going to add some more heavies around the edges.

翻譯年糕

Hi guys! I've finally decided to give the Anycubic clear eco resin a go. I though I'd just try it out on a piece I knew worked in the opaque colours and then adjust from there but to my surprise the detail came out perfect first time... Well on the one side it did anyway.

Once I got the price off the plate I noticed that the supports on the back of it's head were one solid lump now. Initially I thought this just meant I needed less grouped supports for printing clear, but when I removed the ear supports which are quite spaced out I noticed there was a lumpy ridge along the back between where each support joins the model. I've tried to take some photos to show what's happening but it's difficult with the clear resin. I've included an example of a primed grey cast to show how smooth it should be.

Anyone else experienced this and got any tips to fix it? I'm unsure given how perfect the actual face and such came out ?

翻譯年糕

My LCD screen appears to be broken, it's got long lines across the screen while performing the uv exposure test. Tried reseating the cable, but no luck. Could I try something else or should I replace the screen? Any help would be appreciated!

翻譯年糕

Greetings. I am about to pull the trigger on a photon S. And then I noticed that there is a Photon-S with upgraded mainboard and a non-upgraded version.

Upgraded: (aliexpress links)
https://bit.ly/2IpV4kR

Non-upgraded:
https://bit.ly/39i2imF

There is around 30 USD price difference, but I cannot figure out whats the difference is between the two models.

Any hints?
They list the stuff in picture, but AA is in both models... I am confused..

問候. 我正要在光子s上扣動扳機. 然後我注意到有一個photon-s有升級的主機板和一個未經升級的版本.

升級aliexpress連結)
https://bit.ly/2IpV4kR

未升級:
https://bit.ly/39i2imF

大約有30美元的價格差異, 但我無法弄清楚這兩個模型之間的差別是甚麼.

有甚麼暗示嗎?
他們在圖片中列出了這些東西, 但aa都在兩個模型中... 我很困惑..

· 查看原文 · 為此翻譯評分

Hello all! New photon s printer person here. After a slight bit of trial and error (REALLY have to tighten down that level screw :D ) I did get the stress test thing to print just fine and some other stamps I was making for embossing leather to print wellish too. I wanted to make something neat I found on thingiverse: https://www.thingiverse.com/thing:4072298 it looks super cool but was printed in the example on a FDM. For SLA, can I just plop the stls into like photon workshop? (It fits the build platform). I think my biggest question is with the case itself, it has the main hole in it and printing it flat might be bad because of no draining? I can maybe print it straight up and down?? or do I have to print it at an angle with supports? Advice? (if i can get away with laying it flat it would print super fast) 翻譯年糕

using chitubox 1.6.3, when i go back into a saved project and try to edit a support, in this case by adjusting the height, it moves the support completely off the model. Anyone else experiencing this or have a work around?

翻譯年糕

Edit, was not a problem with chitubox or photon. I missed making these items a boolean mesh before export

Ok heres a problem I'm hoping you can help with. I've cut and keyed a model in zbrush, but when I load it up in chitubox or photon workshop the holes are closed up. What's is causing this

編輯, 不是chitubox或光子的問題. 我錯過了在匯出前把這些項目變成布林網格

好吧, 這是一個問題, 我希望你能幫忙. 我在zbrush剪掉了一個模型, 但當我把它裝到chitubox或光子車間, 洞就關閉了. 是什麼導致這個

· 查看原文 · 為此翻譯評分