Anycubic Photon Printer Owners 造訪社團 » Lite

原文網址 Joe Broggio
2019-11-06 04:52:51

Has it been your experience that the Anycubic Maroon resin is kind of trash?

I've had my Photon for a year and have printed a bajillionty things no problem. I have had the Photon S for a few months and similarly, no problem. I typically use AC grey but also have used E-sun yellow PLA, E-sun clear, AC Green, Siraya Tenacious, and so on. No problems.

I have absolutely *not* been able to coax good results out of the AC Maroon on either printer.

On the Photon S, all the prints start to peel off a corner of the plate no matter how many bottom layers and exposure. I'm up to like 6 bottom layers / 80 seconds and 13 seconds regular exposure (which is way overexposed) and it still peels (see attached). Note I am not using a raft, it just kind of looks like it because I placed the parts close - but the problems happen either close or widely separated.

On the OG Photon, it does a little better - because I can use the resin exposure test I dialed it in just right to 12 seconds. Even still, some of the parts literally separated mid-print (that part that peeled up is not supposed to have done that, it's a hollow box).

These are parts that are properly hollowed and drain hole-d!

Is the Maroon just trash resin?

翻譯年糕

Chris Page
2019-11-06 04:56:04

Pranjal Seth
2019-11-06 04:59:06

Darian Peavy
2019-11-06 04:59:40

Joe Broggio
2019-11-06 04:59:54

Darian Peavy
2019-11-06 05:01:11

Joe Broggio
2019-11-06 05:01:13

Scott Schwoppe
2019-11-06 05:01:32

Joe Broggio
2019-11-06 05:04:28

Chris Page
2019-11-06 05:04:55

Christopher Thompson
2019-11-06 05:06:34

Joe Broggio
2019-11-06 05:06:48

Joe Broggio
2019-11-06 05:07:56

Chris Page
2019-11-06 05:09:37

Anthony Tapp
2019-11-06 05:11:16

Caio Donini
2019-11-06 05:33:53

Wayne Rogers
2019-11-06 05:41:29

Stefan Giudici
2019-11-06 05:47:05

Joe Broggio
2019-11-06 05:53:03

Joe Broggio
2019-11-06 05:55:04

Sean O'Hayer
2019-11-06 05:55:30

Wayne Rogers
2019-11-06 06:05:12

Lora Delvecchio
2019-11-06 06:07:53

Joe Broggio
2019-11-06 06:14:19

Joe Broggio
2019-11-06 06:14:24

Joe Broggio
2019-11-06 06:15:05

Joe Broggio
2019-11-06 06:15:09

Sean O'Hayer
2019-11-06 06:16:28

Sydnee Davidson
2019-11-06 07:05:23

Mike Nye
2019-11-06 07:16:53

Joe Broggio
2019-11-06 07:37:01

Sydnee Davidson
2019-11-06 07:39:01

Ken Anthony
2019-11-06 08:23:24

Karel Svoboda
2019-11-06 10:32:09

Bill Connelly
2019-11-06 10:49:09

Joe Broggio
2019-11-06 12:57:10

Paul Edwards
2019-11-06 16:22:36

Guti Gutmann
2019-11-06 16:53:35

John Bubuz
2019-11-06 19:40:53

David Anthony Vivas
2019-11-06 20:54:00

Joe Broggio
2019-11-06 21:33:44

Joe Broggio
2019-11-06 21:34:14

David Anthony Vivas
2019-11-07 02:50:59

David Anthony Vivas
2019-11-07 02:54:09

Patrick Haeflinger
2019-11-07 02:59:50

David Anthony Vivas
2019-11-07 03:03:24

David Anthony Vivas
2019-11-07 03:03:54

David Anthony Vivas
2019-11-07 03:04:21

Patrick Haeflinger
2019-11-07 03:16:47

John Bubuz
2019-11-07 03:24:44

David Anthony Vivas
2019-11-07 03:29:24

Joe Broggio
2019-11-07 06:15:04

David Anthony Vivas
2019-11-07 06:44:46

Joe Broggio
2019-11-07 06:45:34

Στεφανος Κοπανακης
2019-11-07 16:25:51

David Anthony Vivas
2019-11-07 19:48:35

Στεφανος Κοπανακης
2019-11-07 19:51:31

David Anthony Vivas
2019-11-07 20:23:10

Στεφανος Κοπανακης
2019-11-07 20:26:50

Joe Broggio
2019-11-08 16:16:13

原文網址 Juli Forthewin
2019-11-05 02:08:19

15 Kilos Sunlu PLA+, 2 Liter Anycubic Grey, 5 FEPs and 10 Liter of IPA. Should be enough for a few weeks.

翻譯年糕

Andriy Lutsenko
2019-11-05 02:40:29

Juli Forthewin
2019-11-05 02:41:56

Andriy Lutsenko
2019-11-05 02:49:47

Juli Forthewin
2019-11-05 02:51:17

Brett Isaacs
2019-11-05 02:54:29

原文網址 Hershel Vazquez
2019-11-03 23:35:15

Can't denied the printer its amazing, regardless all the crusade for get it work

It's and amazing result with monoprice black

0.03 layer at 15seg

( I rather use anycubic resin it's faster and smell less, but i have like liter and half of this monoprice)

Custom joker Head 1/12 for Soap Studio version

翻譯年糕

Ekaterina Vitalyevna
2019-11-03 23:41:30

Hershel Vazquez
2019-11-04 00:28:04

Ekaterina Vitalyevna
2019-11-04 00:28:31

原文網址 Sercan Güzel
2019-11-03 23:35:01

Had my screen replacement couple of weeks ago now i had time to change it.

With that little component number, how is this an engineering nightmare ? All that space in there and literally none of them is working space ...

翻譯年糕

Jon Hammersley
2019-11-03 23:40:20

Sercan Güzel
2019-11-03 23:40:53

原文網址 Lee Baxter
2019-10-29 18:00:49

This was my biggest print yet in terms of filling the Z volume. Came out well. It was also the easiest support removal ive done so far. haha they literally fell off. World cup trophy

翻譯年糕

Jason Pook
2019-10-29 21:30:56

Lee Baxter
2019-10-29 21:31:19

Lee Baxter
2019-10-29 21:31:31

Jason Pook
2019-10-29 22:06:05

Lee Baxter
2019-10-29 22:06:43

Jason Pook
2019-10-29 22:07:02

Aaron Michael Saucedo
2019-10-30 01:54:31

Damien Greysis
2019-10-30 05:21:58

Lee Baxter
2019-10-30 07:30:23

Lee Baxter
2019-10-30 07:30:52

Damien Greysis
2019-10-30 07:31:46

Lee Baxter
2019-10-30 07:36:59

原文網址 Harald Thingbø
2019-10-29 02:35:22

As Robert Daubar posted a link to NASAs gallery of 3D-models yesterday, it reminded me of a project I made last year. It is a model of the TESS satellite in 1/87 scale. The model was made for Norsk Landbruksrådgivning, a Norwegian agricultural consulting firm that was making an exhibition model to show modern agriculture with, among others, GPS-steering of tractors. To show this they wanted a scale model hovering above the diorama.

翻譯年糕

Harald Thingbø
2019-10-29 02:36:15

原文網址 Robson Scerri
2019-10-27 04:46:08

Hey guys, so I started printing (finally) I started with a simple Campfire from Artisan Guild and now I've tried printing a miniature. The problem is that the supports sort of moved and became part of the model. As you can see below, the support to the left side of his face literally became part of his helmet. I cannot take a decent pic of the miniature to explain better. Do you think that I should increase/decrease the exposure time? 7.5 seconds 0.025 layers using AnyCubic Green that came with the printer.

翻譯年糕

Stephen Exall
2019-10-27 04:51:57

Robson Scerri
2019-10-27 04:53:21

Stephen Exall
2019-10-27 04:59:28

Robson Scerri
2019-10-27 05:01:15

Stephen Exall
2019-10-27 05:04:42

Robson Scerri
2019-10-27 05:15:35

Stephen Exall
2019-10-27 05:17:43

Robson Scerri
2019-10-27 05:20:01

Chris Baker
2019-10-27 07:18:20

Justin Cupitt
2019-10-27 07:28:55

Tiernan Messmer
2019-10-27 09:34:17

Robson Scerri
2019-10-27 13:24:52

Robson Scerri
2019-10-27 13:25:53

Tiernan Messmer
2019-10-27 13:26:00

Tiernan Messmer
2019-10-27 13:27:10

Robson Scerri
2019-10-27 13:31:17

Tiernan Messmer
2019-10-27 13:31:54

Krunoslav Zlomislic
2019-10-27 14:51:40

Tiernan Messmer
2019-10-27 15:51:27

Robson Scerri
2019-10-27 19:51:55

原文網址 Phillip Kenney
2019-10-25 01:44:06

Resin exposure times, I know we love to share this spreadsheet but honestly, these numbers don't even seem right for most of these brands/colors. It literally never gets updated with new info. I don't trust this spreadsheet at all and every time anyone shares it, I cringe a little. How can we come together as a group and really get this spreadsheet calibrated / updated? Or... Just do the resin test and figure it yourself seems to work 100% :p

翻譯年糕

Phillip Kenney
2019-10-25 01:46:31

Joseph Daniels
2019-10-25 01:48:50

Lee Allen
2019-10-25 01:49:50

Stefan Giudici
2019-10-25 01:57:02

David Bartholomew
2019-10-25 02:01:30

Phillip Kenney
2019-10-25 02:05:25

Paul Songer
2019-10-25 02:15:30

Ric Watts
2019-10-25 02:21:22

Sydnee Davidson
2019-10-25 02:23:41

Mourni Tenchou
2019-10-25 02:41:33

Savio Ku
2019-10-25 02:42:40

Bob Deblier
2019-10-25 03:00:06

Ric Watts
2019-10-25 03:05:25

Ric Watts
2019-10-25 03:05:49

Simon Wilson
2019-10-25 03:09:33

André Nettermann
2019-10-25 03:42:31

Ric Watts
2019-10-25 04:06:05

Dustin Oliverius
2019-10-25 04:06:06

Phillip Kenney
2019-10-25 05:55:52

Justin Cupitt
2019-10-25 06:26:10

Justin Cupitt
2019-10-25 06:29:04

Peter Ede
2019-10-25 06:59:17

Szymon Buhajczuk
2019-10-25 07:38:38

Scott Pavlich
2019-10-25 07:40:08

Ioan Flerr
2019-10-25 19:59:03

Tero Konttila
2019-10-25 20:21:04

Jack Slack
2019-10-26 01:00:00

Paul Mendoza
2019-10-27 14:27:32

原文網址 Joey Sheldon
2019-10-20 01:49:00

Someone out there made an actual statue of Vladimir Lenin, Mickey Mouse and Jesus.

I cloned it pretty poorly by mixing 3 people's models of the respective people/characters. The models had no rigging so it was literally tear the arm off and remesh with a rotated arm. The result is still pretty comical.

翻譯年糕

John Rodriguez
2019-10-20 02:46:15

Darren Donovan
2019-10-21 01:10:52

原文網址 Elle Heilig
2019-10-19 10:00:20

Whelp, I overfilled once (literally once) and got resin in the ball joint which prevents it from fastening securely.

I went to disassemble and clean everything, and I can't get one of the four screws that hold the build plate on because it looks like resin has clogged the hex slot.

I'm soaking the assembly overnight in IPA, does anyone have any other suggestions?

翻譯年糕

Harold Crossley
2019-10-19 10:03:54

Gabe Snooks
2019-10-19 10:08:36

Joel Glass
2019-10-19 12:25:19

Jason Carlisle
2019-10-19 13:31:08

Elle Heilig
2019-10-19 13:31:32

Jason Carlisle
2019-10-19 13:46:18

全不選發文排行