Anycubic Photon Printer Owners 造訪社團 » 用戶發文

Hey guys, quick question.
I just had a print fail bc of a pre-supported file that didn't work for my setup. The print now sticks to the fep. What is the easiest way to remove the print without damaging or scratching my fep? Lift with my fingers? Use the plastic spatula? Soak it in ipa for a while?

翻譯年糕

Hey guys!

//edit its Chitubox obviously c:

I'm having some problems with suppport placement. I'm trying to place something under the chin here, but regardless of how much i click I can't add a support.

Maybe something like minimum distance or smth is blocking it. Any advice? What setting do i need to adjust to be able to manually place one here successfully?

Thanks a lot and ahve a lovely day!

翻譯年糕

Hey guys,

I didn't print anything on my photon in like 2 months and started printing again using a new bottle of Anycubic Grey. So far I only used Anycubic Green (translucent).

But I really struggle with this grey resin. I'm getting strange artefacts on my prints, that appear randomly on certain layers across multiple minis. I also have some goop sticking to the FEP. They are like flakes and can also be found on parts of the minis.

I also noticed that some parts of my prints such as the wolf's paws or the feet of the goblins merge together with the base or are flattened out. I tried doing an exposure test previously, and also had these artifacts. Due to not perfect leveling I didn't use the exposure test results and releveled first.

Could it be some mechanical failure like light leakage?

I took the exposure settings from the spreadsheet.

0.05mm layer height.

18sec exposure

1sec offtime

base layers 90sec

8 base layers.

I reduced the exposure to 14 later, since i saw some posts of people saying the exposure was far too high on the spreedsheet, but the results were the same.

The fep was very tight, maybe even too tight. I will replace it for a testprint with the remainder of my anycubic green.

翻譯年糕

Hey guys, quick question. I haven't printed on my photon in a month and decided to try my anycubic grey resin with my first print.

I made the little Lithoophane at 46 degrees with anycubic grey using the settings from the spreadsheet so I know it's not dialed in perfectly yet but I think my issue is unrelated to exposure times and looks more like a mechanical issue.

Could these lines be the infamous z-wobble?
Thanks in advance guys. I'll deliver my exposure settings in a few minutes.

翻譯年糕

Hey guys, I've been struggling really hard with small but simple prints. I'm still a newbie regarding resin prints. Any beginner advice is appreciated!

I've printed the yelling beard statue earlier without any problems, but printing a small piece like this (see picture) always ends up in a failure.

It prints the supports, but the main object sticks to the vat.
Does anyone know what my newbie mistake is?
The buildplate should be leveled correctly. I printed 2 yelling beards earlier, now I releveled it just in case and the current yelling beard print makes satisfying FEP pop sounds so far.

The supports are automatic light supports cause the object is small. I hope that's not a logic error?

Resin: anycubic green.

Thanks a lot!

翻譯年糕

So I've been using different slicers and I struggle hard with support placement. And it's not about where to supports its that I literally can't place them.

I see an island, E. G. The fist of a miniature floating around. After auto supports I try to add thin supports to the fingertips but when I click nothing happens. I've been using the anycubic slicer and chitubox - both gave me the problem. I'll update with a photo asap after restarting my pc.

翻譯年糕

Hey guys, I was gonna order my printer soon and I found an ebay shop that apparently is owned by anycubic? However, there are a few shops that imo stole the name and a second official shop that appears to cater to the US market whereas the one linked below is for EU (the same printer is put up multiple times with the same descriptions in different languages). Update: I also just found a German shop where the printer costs 400....

The printer goes for like 370 bucks there, and according to what I heard from others this is around the price the printer goes for when on sale on amazon or similar.

Question:
Can anyone confirm that purchasing my anycubic from the ebay shop is safe and that I will get the original product? The seller reviews are 99% positive and the negative ones only complained about deliveries and such.

https://www.ebay.at/str/anycubic

Thanks a lot!

翻譯年糕