Anycubic Photon Printer Owners 造訪社團 » TIP

Had an interesting failure today...

Was printing a mini, and left and right the parts stuck to the buildplate, but the center where the mini was it stuck to the FEP.

What makes it weirder is that "just" before this mini, I had a print that was only on the center of the build plate and that succeeded.

Checked my FEP, it's at 300Hz so that's ok.

Cleaned my buildplate (this time manually with alcohol wipe, rather than in the Anycubic washer and let it dry)

For now I just re-leveled the printbed (home, down till I cant move buildplate, tighten, raise buildplate 0.3, set z=0.

And adjusted initial cure from 50 sec to 60.

Anything tips on what (else) I should check?

(I suspected a concave build-plate but already checked that.)

翻譯年糕

Does anyone have any recommendations for priming? Iv never primped one of my prints so I wanted to know if there was any good tips for it

翻譯年糕

Standing multiple parts.

翻譯年糕

Same models difference size as customer needs. Drip Tip Vape.

翻譯年糕

Planning on using a fairly large piece multiple times for a 40k army. I’m thinking I should print the bits needed, make mould and then use the moulds.

Can someone point me in the direction of what I’d actually need to do and what materials I might need.
For clarity it’s mainly wheels and frames which woo be built on layer if that makes any difference

翻譯年糕

I'm currently working on some pickup rings in fusion 360 and I was wondering if any of you had any tips on how to buff resin prints to a gloss. Top is original, bottom is prototype test print. I've tried to hit it with a 3000 grit sandpaper, but still looks a bit scratchy.

我目前正在fusion 360的一些取貨戒指, 我想知道你們當中有沒有人知道如何將樹脂印到光澤上的提示. Top是原創的, 底部是試版. 我試過用3000 grit sandpaper打它, 但看起來還是有點癢.

· 查看原文 · 為此翻譯評分

Good afternoon. I have a problem choosing settings for photopolymers in model S.

Can you tell me your settings to help save money and time, and not try everything by trial and error.

I use a printer to print miniature. A recent attempt at printing gave a good result, but I feel that the printer might work better.

Can you share your experience, tips and tricks?

I print on a gray, black-green photopolymer from Anycubic.

Is there a better choice in terms of price and quality?

What settings do you recommend for what is indicated above?

翻譯年糕

PSA: Remember to resin when you’re doing 17 hour prints. ?

Also as a side note, this is the second time in two weeks I set and forgot and found this mess. Anyone have any good tips for leaving it? Last time I used goof off to clean it but that still took awhile.

翻譯年糕

The edges of my shelf are curling up, any tips to avoid this please?

翻譯年糕

Hello folks!
Thanks a lot for many precious tips avilable here.

Conducting tests to improve printing size up to up to 1 mete r!
Since my Photon is under maintenance (dued to wobble issue), I'm conducting some test in order to discover real software potential.

I modified "__dlpconf_" file to following machineSize values (mm): X:68.04 Y:120.96 Z:1000
In simple terms I tried modify Photon printer profile in order to achieve printed piece up to 1 meter. Anycubic Photon Slicer V1.3 software allows slicing "oversized" STL model and I got *.photon file (2.8 Gb!).
After launching file print comes test failure : Printer lowers its platform to home (I manually simulate home to sensor) but printer keep lowering instead of printing. (Video shows test)
Printing progress goes from 1% to complete without any printing process. Do you think printer firmware (Photon 5.5, V4.2.3_LCD) allows "oversized" printing? In case answer is "NO" do you know about open source software I could install on printer allowing custom profiles?
Thank you all for reading and help! ? 翻譯年糕