Anycubic Photon Printer Owners 造訪社團 » IDE

do you need back side of this shield? If i wolud lean it back a bit to keep it on buildplate ;)

You'll mostly get some curling out at the ends. If it's a flat surface the supports are attached to I'd print it directly to the bed.

ok thank you. What do you mean curling ? The part will curl ? Wasn’t sure you could print it directly in the bed. Just about everything I’ve seen shows supports on the bottom

I’d angle it back some and add more supports along the way. It will reduce the print time by a large margin.

Like this?

that is a removable panel/door so the back part of it will be seen and used a lot

could you explain how that will make the print time faster please?

Jimmy Clark your printer works one layer at a time. The taller the print, the more layers you will need.

By angling the print you cover a larger surface area at once.

If you were to lay it flat on the build plate it would take 30 minutes or so. But standing up depending on size it could take 14 hours.

Jimmy Clark i don’t know how printing flat on the plate would work. It would certainly make it harder to remove.

But printing it at an angle will allow more supports to be placed below and increase adhesion to the plate. In addition to also cutting print time down overall.

Jimmy Clark yep

Christopher Barnes laying other flat would use less support and less of a chance damage when removing the supports but would it make it that much harder to remove the print?

?

Jimmy Clark flat wouldn’t require any supports assuming the back is flat. It would also be the fastest. It’s possible to remove the item. I have never printed flat though.

You can also place stuck prints with the plate in the freezer for a little. It should just fall off once it gets cold enough.

Jimmy Clark angle more to make it lower and shorten print time. Add more supports and spread them around evenly. Also watch these videos if you haven’t.


https://www.youtube.com/playlist......

Is impossibile to download

cool thank you

What resin are you using?

its at the bottom of the post but its the Anycubic Grey resin

James Swan oh... its in the photo...

James Swan should change your bottom cure time to 70s... https://docs.google.com/....../1crvzMnt....../htmlview......

James Capps those settings are for the Photon, I have the Photon S and these settings have never worked for me

James Swan ??

James Capps thanks though

James Swan https://docs.google.com/....../1vQsW9y5gJKTmv....../htmlview have you tried these?

James Capps yea thats what i started from, i havent had any issues printing miniatures, just lately this suction issue

James Swan thats really weird.. do you have a pic of what your printing with the holes you put for drainage/air?

James Capps The handle bit has a hole in the top and bottom, but it hasnt made it that far to even matter.
Im about to try it again without the handle and print that on its own.

James Capps so here is what comes out, I first thought it was leveling but I flipped the design and it happened in the same side as the first

And the other side always prints out fine

Did you create the supports in chitubox?

James Capps custom supports in chitubox yes

James Swan Every-time I have used chitubox for supports i have had a bad time. Maybe try again using prusa slicers auto supports and exporting the stl with supports and import into chitubox to slice.

James Swan if anything hopefully someone sees all the stuff you have done so far and chime in with some advice ?

From what I can see one of the raft layers is peeling up and seperating from the rest of the raft is that right?

Usually I use only prusa for support.. Where did you find the handle? Is in scale to fit in your plate? ? ?

Jacob Palmer yea that’s it
Sorry didn’t see your msg

What temperature is the room you're running the machine in. Sometimes low temp can cause delamination, but usually it happens in more than one layer...

Try tightening your FEP

I'd say the various islands are going to be a way bigger problem :x

Lift off the bed

I prefer larger prints. You may want to put a few holes in the bottom, but they won't be a problem if you're adding supports under it. Also, tilt it back just a little so that flat bottom doesn't print all in one go.

Biggest print I’ve done so far

was that one piece!

i was thinking of printing it with no lift at all

Tom Barnes 10. It took 60 hours, 5 print beds

not that many tbh, mostly the arrow fletchings and the braid bottom.
the ear lobes are floating though and the software wont place any supports there, manually or automatically :L

You could print her way bigger, turn her sideways and add some supports, hollow with 3-4 holes on the bottom I bet you could get her to 5-5.5” tall

Tom Barnes then holes in the bottom won't help.

I had printed this model with no problems, I may even have file with manual support ;-)

if you do please can you share that with me! then I can analyse is and learn from it!

PM

Here is my workflow that I have for models like this

1. Hollow with chitubox and add some holes to prevent suction cupping preferably the bottom layers towards the plate. And export stl.

2. Open in prusa slicer and lean it back as to prevent supports on the face and to prevent a large flat surface on the plate. Refer to the beginners guide if you want more info why. Then add auto supports in prusa using the basic settings. reorient till you’re happy with the supports and export stl with supports.

3. Import hollowed stl with supports into chitubox and slice then look through the slice for any large islands and ad manual supports in chitu as needed. Once done take slice to the machine ?

Ps use really hot water to separate the supports after ipa but before cure

Attached a pic of my results

I've had issues with holes on the bottom blending with the surrounding base, so make sure it's fairly large, I'd say 3 or 4mm. Tilting isn't necessary but will help drain as it prints instead of after.

It's working so far

Looks awesome dude! Great share ✔️

Nice.

Nicee! How did you orient the prints? Sorry if I'm still new to this

Thomas Niccolo Filamor Reyes

Thomas Niccolo Filamor Reyes

Thomas Niccolo Filamor Reyes

Thomas Niccolo Filamor Reyes hope those pics help

Hoghead Hoffer lovely! Thanks, will use these as my guide and reference

Thought that was a great program! Great copy’s too bud!

Nice replicas. Show pissed me off though.

So sorry to hear that. Stay safe.

Sorry to hear! all the best and quick recovery!

Get well soon

We wish your artist and everyone else afflicted with a speedy recovery

Hope the artist makes a quick recovery. Hope the family is ok stay safe everyone

Prayer to the family. That being said, link doesn't work,

too many hits. try later.

Praying for the artist and his family and I have the thrall printing as we speak. It was wonderul you guys did this in the artist honor. It's a beautiful sculpture.

James Teagle ?

Get well soon!!

Amazing warewolf. Our prayers and good wishes for your team from Australia

Sorry to hear that. Hope hi get well soon!

Konstantinos Martinos ?

Access denied ?

I really like Poly Juice water washable by filaments.ca.

Anycubic Eco has much less odor.
Also adding the filter helps a lot

Tell me more about the filter. Still new to 3D resin printing.

Elegoo gray is much better. Also Dragonresin gray.

Comment to follow

Is that the plant based Elegoo gray? Or the regular?

Tell her to stay out of the garage on print days.

Matthew Beauchamp
Regular is much less odorous.
I haven’t tried the plant based.
I hear the water washable is good.

Anycubic green is one of the smelliest resins. Kinda brittle too

Monocure Rapid 3D is definitely lighter on the odour than the Anycubics, but when I had the printer at work my boss still complained about it. I may just have no smell....

I found the IPA smell was also strong, trying water washable resin now.

IMO Anycubic Red have very tiny smell. But green and black smells awful. Without ventilation you can't sit with printer in room.

Matthew Beauchamp I've installed 3M filter with an additional duct in my Photon S.
https://www.thingiverse.com/thing:3591774


Also I've read about the success with DeStinkyNator a couple of times in the group.

https://www.thingiverse.com/thing:4007108

Get the anycubic plant based eco resin. It has virtually no smell and there's no difference from the standard resins as far as detail goes

Pues elegoo gris lavable 0 olores ?? dentro de casa ?

Hi, you have Ifun 3120W low odor https://lesresines3d.fr/....../45--standard-rigid...... ?

Alexandra Print you atr manufacturer?

Saša Sinek no reseller

Time for a new wife.

Elegoo resins barely smell at all. I'm using esun at the moment and that also doesn't have much of a smell.

I also use an expensive resin called Nextdent model ochre. It's a dental resin and has no Smell at all. £240 a litre though so might be a bit much just to get rid of the smell

Forget to take off the plastic?

Or spacing may be off if you have a glass protector on the screen.

I dont have a screen protector on and i for sure took the plastic off

Following, because, same here. No protective sheet. Print time went from 7.5 seconds to 13. Same everything except FEP

Which screen did you buy to replace your old one?

https://www.ebay.com/....../2560x1440-LCD....../184099653038

Gregory Thompson that one

Michael Paulick i changed my fep just to see if it fixed it and nothing I feel your pain

Wes Shawshank Crain it claims to be an Anycubic brand in the description. I was thinking if it was non-brand that it could possibly be filtering too much light. Hope you get it worked out

That’s awesome. Does it have a stand?

Brian Wulff nah I need to make one for it

Tucker Adams is it able to stand on its own? Orrr

Brian Wulff nope lol

wicked... :)

What is this from? Is it a original character?

James Capps Storm Javelin from Anthem

Beautiful that mate. Can I ask how many parts you were able to get it down to? ?

Rich Harrison 6 parts total. It came broken down from the designer

Tucker Adams good stuff. Love the paint work. Are you on Instagram?

Rich Harrison I am not, I should get one put together though. Need to think of a name for it lol

Tucker Adams let me know when you do ?