Anycubic Photon Printer Owners 造訪社團 » ROS

原文網址 Paul Ciao
2020-01-08 14:35:01

I'm so happy with Benjamin Tam's sneaky boi. Printed in Polyjuice water washable resin at 0.05mm later height with his sneaky little bros in all their sneaky glory.

Edit:

Thanks for the positive responses! To get it this clear, here's what I've done:

Slicing- do not hollow. Hollowing diffracts light passing through it (passing through 3 mediums: resin, air and resin) making the model appear more translucent.

Curing- one huge benefit of the water washable resin is that you don't need an UV light to cure which causes yellowing if your cure it for too long. I let the model air-dry for at least 24 hours before clear coating.

Clear coating- this is what turns the model translucent to clear. I use 2 coats automotive clear coat on all sides of the pieces and give it 48hours to dry before assembling. Extremely important: clear coat before gluing the pieces together as noncoated sides diffracts light reducing the transparency. This also has a positive side effect at reducing the yellowing if your prints come out slightly yellow.

Printing- the most important. Use fresh resin every time you print. Anyone who has printed using clear resin probably had a print already come out yellow. UV exposure over time in the vat will cause yellowing and I found that after 8-9hours in the vat, the remainder will start yellowing. Therefore I try to minimize the print time (0.05mm layer height + 10s exposure) by only using just enough resin to complete the print and refill the vat before the next one.

Hope this helps!

翻譯年糕

Eric Weber
2020-01-08 14:36:18

Federico Monfalcon
2020-01-08 14:41:23

Huynh Thien Phuoc
2020-01-08 14:43:41

Jorge Salazar
2020-01-08 15:02:23

Benedikt Maderholz
2020-01-08 15:04:09

TJ Strickland
2020-01-08 15:07:56

Enos Rossi
2020-01-08 15:21:06

Justin Cupitt
2020-01-08 15:31:05

Chris Kouvelis
2020-01-08 15:37:21

Étienne Dré Landry
2020-01-08 15:37:43

Étienne Dré Landry
2020-01-08 15:38:03

Chris Kouvelis
2020-01-08 15:38:23

Étienne Dré Landry
2020-01-08 15:40:17

Marcin Bocis
2020-01-08 15:48:13

Daniel Schwarz
2020-01-08 15:50:25

Paul van den Dries
2020-01-08 16:08:25

Tom Logan
2020-01-08 16:09:13

Vincent Balmont
2020-01-08 16:13:23

Allison Janssens
2020-01-08 16:26:26

El-Aras Buğra de Kabaca-Luchador
2020-01-08 16:37:31

Elle Heilig
2020-01-08 16:42:09

Elle Heilig
2020-01-08 16:43:14

Ben White
2020-01-08 17:13:15

Joao Claudio
2020-01-08 18:01:28

Scott Gordon
2020-01-08 18:22:47

Curtis Finnigan
2020-01-08 18:26:41

Benjamin Tan
2020-01-08 18:50:14

Benjamin Tan
2020-01-08 18:50:33

Benjamin Tan
2020-01-08 18:51:10

Benjamin Tan
2020-01-08 18:52:50

Federico Monfalcon
2020-01-08 18:53:43

Vincent Balmont
2020-01-08 18:56:46

Peter Bolger
2020-01-08 19:15:09

Bruno Tabarani
2020-01-08 20:55:23

Frank Padula
2020-01-08 22:14:02

Alex Danis
2020-01-08 22:29:21

Elly Madrigal
2020-01-08 22:36:29

Ron Staton
2020-01-08 23:02:31

Darran Taylor
2020-01-08 23:34:43

Telli Mantelli
2020-01-08 23:58:57

Madison Martins
2020-01-09 00:52:44

Alex Danis
2020-01-09 01:37:10

Alex Danis
2020-01-09 01:37:32

Madison Martins
2020-01-09 01:46:36

Alex Danis
2020-01-09 01:46:55

Alex Danis
2020-01-09 01:47:42

Kevin Deiman
2020-01-09 02:39:54

Dave Green
2020-01-09 02:42:42

Alex Danis
2020-01-09 02:43:20

Dave Green
2020-01-09 02:43:46

Alex Danis
2020-01-09 02:44:49

Alex Danis
2020-01-09 02:45:03

Alex Danis
2020-01-09 02:45:32

Joseph Daniels
2020-01-09 03:30:25

Tyron Craft
2020-01-09 05:00:36

Omar Baez
2020-01-09 08:01:04

Jorge Salazar
2020-01-09 08:46:58

Paul Ciao
2020-01-09 10:38:52

Reneo Santos
2020-01-09 11:04:03

Ben White
2020-01-09 11:35:50

Jorge Salazar
2020-01-09 12:55:07

Paul Ciao
2020-01-09 14:37:57

Paul Ciao
2020-01-09 14:40:02

Paul Ciao
2020-01-09 14:42:03

Huynh Thien Phuoc
2020-01-09 14:48:11

Ronald Smith
2020-01-09 22:52:09

Davide Rizzo
2020-01-10 14:12:20

Paul Ciao
2020-01-10 14:32:23

原文網址 Cannon Rigger
2020-01-08 06:46:15

Painting the Roses Red with Anycubic Clear at 0.2mm and 14 sec exposure time. The extra exposure time may have helped prevent the thin walls from splitting as they did in a previous attempt using 12 sec exposure.

STL is ROSE by hanhan on Thingiverse.

翻譯年糕

Ben Brooks
2020-01-08 06:53:18

Cannon Rigger
2020-01-08 06:54:50

Ben Brooks
2020-01-08 06:59:10

Cannon Rigger
2020-01-08 07:00:35

Ben Brooks
2020-01-08 07:01:31

Cannon Rigger
2020-01-08 07:04:21

Ben Brooks
2020-01-08 07:08:34

Ben Brooks
2020-01-08 07:08:50

Jorge Salazar
2020-01-08 07:50:18

Cannon Rigger
2020-01-08 07:52:05

Jake Walker
2020-01-08 08:32:43

Cannon Rigger
2020-01-08 08:39:50

Jorge Salazar
2020-01-08 09:03:47

Jake Walker
2020-01-08 10:34:59

Cannon Rigger
2020-01-08 10:56:03

Jake Walker
2020-01-08 10:58:07

Cannon Rigger
2020-01-08 10:59:38

原文網址 Matt Mendez
2020-01-07 09:12:20

Started with the photon.
Saw the potential.
Grossly overshot the next steps.
Got the the Photocentric Magna for my shop.

I'll just leave this here as my unboxing video ? ?

翻譯年糕

Kelli Lubeley
2020-01-07 09:16:25

Léo Protopappas
2020-01-07 09:24:53

Will Hawkes
2020-01-07 09:25:42

Mike Vayakornvichit
2020-01-07 09:28:12

Jacob Hale
2020-01-07 09:30:37

David Collinson
2020-01-07 09:32:04

Stephanie Diaz
2020-01-07 09:32:47

Matt Mendez
2020-01-07 09:33:20

Greg Fiske
2020-01-07 09:37:42

Matt Mendez
2020-01-07 09:38:41

Matt Mendez
2020-01-07 09:41:59

Ben Knipper
2020-01-07 09:42:36

David Collinson
2020-01-07 09:43:16

Matt Mendez
2020-01-07 09:43:36

Frank Martinez Jr
2020-01-07 09:44:06

Ben Knipper
2020-01-07 09:44:40

Matt Mendez
2020-01-07 09:45:09

Matt Mendez
2020-01-07 09:47:46

Matt Mendez
2020-01-07 09:48:17

Frank Martinez Jr
2020-01-07 09:49:07

David Collinson
2020-01-07 09:50:17

Paul Pazienzo
2020-01-07 09:52:31

Ben Knipper
2020-01-07 09:52:45

Juan Pablo Bagnon
2020-01-07 10:10:36

Matt Mendez
2020-01-07 10:11:55

Doug Larkin
2020-01-07 10:15:37

John Giardino
2020-01-07 10:17:10

John Giardino
2020-01-07 10:20:00

Doug Larkin
2020-01-07 10:20:35

Matt Mendez
2020-01-07 10:50:53

Lance Turner
2020-01-07 11:07:25

Matt Mendez
2020-01-07 11:13:37

Lance Turner
2020-01-07 11:22:13

James Edward
2020-01-07 11:29:40

Jeric Bautista
2020-01-07 11:36:42

Mike Armijo
2020-01-07 12:05:43

Matt Mendez
2020-01-07 12:12:22

Mike Armijo
2020-01-07 12:17:09

Luke Pettit
2020-01-07 12:23:11

Luke Pettit
2020-01-07 12:26:56

Matt Mendez
2020-01-07 12:29:26

Doug Larkin
2020-01-07 13:20:06

Doug Bowman
2020-01-07 13:38:50

Arthur Withier
2020-01-07 18:46:30

Arthur Withier
2020-01-07 18:47:04

Callum McIntyre
2020-01-07 19:22:07

Yessik Ziiq
2020-01-07 19:26:31

Kayo Michiels
2020-01-07 20:08:59

Matt Mendez
2020-01-07 20:32:47

Matt Mendez
2020-01-07 20:33:31

Stefan Giudici
2020-01-07 20:35:12

Ahmad Eivaz
2020-01-07 21:36:14

Frank Martinez Jr
2020-01-07 21:46:31

Bruno Tabarani
2020-01-07 22:12:22

Yessik Ziiq
2020-01-07 22:56:32

Matt Mendez
2020-01-07 23:06:45

Ahmad Eivaz
2020-01-07 23:08:47

Matt Mendez
2020-01-07 23:10:23

Reneo Santos
2020-01-08 00:28:39

David Coates
2020-01-08 01:47:04

Mark Shearin
2020-01-08 01:49:58

Matt Mendez
2020-01-08 01:52:48

Matt Mendez
2020-01-08 04:06:10

Tristan Virevialle
2020-01-08 04:18:58

Gary Bishop
2020-01-08 21:21:06

Matt Mendez
2020-01-08 21:59:26

Gary Bishop
2020-01-09 01:54:25

Ahmad Eivaz
2020-01-09 02:00:34

Matt Mendez
2020-01-09 02:03:58

Matt Mendez
2020-01-10 08:16:34

Ivan Adhi R
2020-01-10 09:18:42

Nipuna Gunarathne
2020-01-12 15:35:44

原文網址 Nicole Cucinello
2020-01-07 00:43:04

So i never heard back from this group on my major photon s problem so I'll try again.

My photon is stopping mid print. the preview on the screen is just showing a blank screen and it was fine in the preview on the computer. It has been doing this 3/4 tries.

An any cubic customer support is useless. last time i did a support entry i never got a reply. I'm going to do another tonight but i'm hoping someone here can help.

Update: I was about two full builds behind (3.4.1 to 5.0.2 lol). So it’s updated and I am trying to print again. Fingers crossed! ?

Update 2: first two prints have gone fine. I think the updates fixed it! Thanks everyone for all the help!

翻譯年糕

Steve Haynes
2020-01-07 00:44:54

Jason D Rush
2020-01-07 00:45:39

Mike Wheway
2020-01-07 00:46:25

Morten Vinther
2020-01-07 00:48:54

Michael Underwood
2020-01-07 00:49:38

Nicholas Taylor
2020-01-07 01:01:41

Cliff Goodwin
2020-01-07 01:24:53

Nicole Cucinello
2020-01-07 01:43:16

Nicole Cucinello
2020-01-07 01:43:32

Nicole Cucinello
2020-01-07 01:43:59

Nicole Cucinello
2020-01-07 01:44:38

Nicole Cucinello
2020-01-07 01:45:45

Mike Wheway
2020-01-07 01:47:41

Nicole Cucinello
2020-01-07 01:47:54

Mark Wardle
2020-01-07 01:50:11

Nicole Cucinello
2020-01-07 01:54:43

Nicole Cucinello
2020-01-07 01:56:10

Nicole Cucinello
2020-01-07 01:57:09

Nicholas Taylor
2020-01-07 03:26:29

Grant Kinnick Smith
2020-01-07 03:28:17

Nicole Cucinello
2020-01-07 03:28:44

Nicholas Taylor
2020-01-07 04:09:39

Adam Scaramella
2020-01-07 04:15:49

Greg Miller
2020-01-07 14:43:05

Paul Ciao
2020-01-11 00:05:24

原文網址 Ronni Kristiansen
2020-01-06 19:27:47

Ok, here's another noob question for you PnP-miniature pros;

What is your favorite way of ensuring perfect prints, with supports and all?

Ie. what software do you use for supports, slicing, testing etc

翻譯年糕

Andrew Sternglass
2020-01-06 19:31:48

Jacob Palmer
2020-01-06 20:04:19

Aaron Kelley
2020-01-06 20:05:25

Joey Smith
2020-01-06 20:23:08

Mark Anthony Vasquez
2020-01-06 21:56:58

Jonathan Dunbar
2020-01-06 23:15:12

Jason Pedersen
2020-01-07 00:07:37

Jarin Udom
2020-01-07 00:55:13

Tauri Icenogle
2020-01-07 02:16:51

Neil Joseph
2020-01-07 03:11:31

Josh Shedaker
2020-01-07 03:47:40

Tauri Icenogle
2020-01-07 03:53:25

Josh Shedaker
2020-01-07 03:58:03

Jeff Hunt
2020-01-07 04:08:45

Jarin Udom
2020-01-07 05:21:03

Neil Joseph
2020-01-07 05:24:25

Jarin Udom
2020-01-07 05:25:14

Bert Harvey
2020-01-07 16:42:25

Ronni Kristiansen
2020-01-07 19:42:03

Ronni Kristiansen
2020-01-07 20:50:50

Jeff Hunt
2020-01-07 23:18:18

Jeff Hunt
2020-01-07 23:19:50

Ronni Kristiansen
2020-01-08 00:11:15

原文網址 Simon Fullalove
2020-01-06 03:12:52

Finally got some prints done and they came grate I over supported them so that’s a redo ?

I tried to print 6 x3 cal Ross the back and x3 across the front of the plate.

I done the levelling process again last night. The x3 that I had on the rear of the plate failed at tray level

So that was a bust ? but happy finally got prints complete

翻譯年糕

原文網址 Antonio David Gallardo Perez
2020-01-05 18:14:02

Hola a todos.
He realizado el test de exposición y no sé bien cómo interpretarlo. La resina es Esun standar gris. Os agradecería me ayudarais. Me pasaron configuración de 13 segundos por capa de 0.05 pero me sale la pieza muy engrosada. La impresora es la Photon S.
Saludossss

翻譯年糕

原文網址 Sydnee Davidson
2020-01-05 06:04:50

What is this stuff!?
I’ve been printing with my Photon for about a year and never came across these paper thing bits. They don’t seem to be interfere with the actual print, I’m just left with having to peel and pull all the bits out of the vat before a do a new print.
Is this what all the “heat your resin” fuss is about? I live in SoCal and it doesn’t usually get that cold, shout it’s reached mid 60s inside while I’m away or sleeping while the printer is running (in a sealed enclosure).
My other thought was that the new Elegoo ABS like grey can’t be mixed with MonoCure Flex or other non ABS like colors, like the regular grey was fine with.
Any input is appreciated!
For reference, I've been recently experiencing this with both: Elegoo ABS like grey + Elegoo Standard Maroon (40/60-ish) Elegoo ABS like grey + Monocure Flex100 (20-25%)
翻譯年糕

James Erik Hodson
2020-01-05 06:10:38

Sydnee Davidson
2020-01-05 06:12:02

Chris Visser
2020-01-05 06:39:17

Chris Crute
2020-01-05 06:44:21

Mark Wardle
2020-01-05 09:04:47

Sydnee Davidson
2020-01-05 09:35:09

Marc de Hoogh
2020-01-05 17:51:07

Sydnee Davidson
2020-01-05 18:03:06

Marc de Hoogh
2020-01-05 18:07:09

Marc de Hoogh
2020-01-05 18:17:17

Sydnee Davidson
2020-01-05 18:25:39

Marc de Hoogh
2020-01-05 19:51:21

Marc de Hoogh
2020-01-05 19:53:06

Sydnee Davidson
2020-01-05 19:59:38

原文網址 Shaun Besman
2020-01-04 08:51:20

Does anyone have a SOLID video on the photon s for beginners and like pros/cons? Too many months of looking at the page, think it’s time to buy one.

翻譯年糕

Aaron McCommon
2020-01-04 08:53:47

原文網址 Wojciech Majkut
2020-01-04 02:12:04

Hi.

I've got question. I used to run Photon and decided to "upgrade" to Zortrax Inkspire some time ago. but I've got quality issues. I use original and 3rd party resins.

I've been searching they FB group and tried with customer support, but they keep saying it's either no problem or area temperature difference causing these issues...

I have funny sagging/ deformations at support-part contact point. Does anyone know what could be a reason?

I started pre-warming resin and keep 22-24C around printer, resin's well stirred (no bubbles), slowed lifting speed, increased exposure and exp time-off, new fep, tried hollowed or full body (no difference), thickened supports too (2mm pillar and 1mm tip) Printer's in stable position and all leveled.

I think it could be either mechanical issue or something is wrong with LEDs, but it's only guessing.

I understand it's different printer, but maybe someone came across similar issue and could help me to resolve it.

Thank you very much for your help.

嗨.

我有個問題. 我曾經運行photon, 不久前決定"升級" zortrax inkspire. 但我有質量問題. 我使用原創和第三方樹脂.

我一直在搜尋他們的fb組, 並在客戶支援下嘗試, 但他們一直說, 要麼沒有問題, 要麼地區溫度差異導致這些問題...

我在支援部分接觸點有滑稽的低調/變形. 有人知道甚麼可能是原因嗎?

我開始預熱樹脂, 在印表機周圍保持22-24 c, 樹脂的井噴(無泡沫), 減慢, 增加曝光和exp, 嘗試空洞或全身(無差別), 厚也支援(2毫米柱和1毫米提示)印表機處於穩定的位置, 全部平穩.

我認為這可能是機械問題, 或者led有問題, 但它只是猜測.

我理解這是不同的印表機, 但也許有人遇到了類似的問題, 可以幫我解決它.

非常感謝您的幫助.

· 查看原文 · 為此翻譯評分