Anycubic Photon Printer Owners 造訪社團 » EVA

I personally like, a lot, this pendant.
Design courtesy: Sascha Vogt
BlueCast X10. Silver 925.
Galloni Pressovac.
Details are unbelievable.

我個人很喜歡這個吊墜.
設計禮貌: sascha vogt
藍調x10. 銀色925.
加侖加侖.
細節令人難以置信.

· 查看原文 · 為此翻譯評分

I use these wipes after i clean with Mean Green and then a quick rise off with warm water and support removal if needed. I take the wipe and wipe down the figure till there are no more shiny spots / areas then wait a min till it evaporates then into the uv curing box. These work great. Can be bought on Amazon. Just remember these are not HAND WIPES. Wear gloves.

翻譯年糕

So I'm trying to dispose of my alcohol. I use denaturated alcohol (the pink kind). I left it in the sun with the top open for like a week but:

1) Resin didn't seem to cure that much. There's a lot of browny residue floating around, that doesn't seem like resin to me. Also the alcohol remained very cloudy.
2) The alcohol didn't evaporate. I mean if it did, it's like 5 mm in 7 days. Is this normal? This doesn't seem very convenient.

Is this because I'm not using IPA? This is starting to become a problem because the alcohol is not cleaning well anymore so I have to dispose of it. I tried to recycle it but didn't go very well. Suggestions? Thanks.

翻譯年糕

I appreciate seeing all of the IPA cleaning alternatives, but I haven't seen much discussion over the disposal process. How are y'all safely taking care of the post-clean chemicals?

To Clarify: I know the usual IPA evaporate/cure approach. I'm curious about how people are handling disposal for the chemical cleaners that people have been suggesting.

翻譯年糕

Hi guys,

I got no print success since I started using the anycubic black.

With anycubic green I had no problems.

Already configured according to Google spreedsheet, but also did not work.

Also I tried on my own configurations, but without success. All complete with some defect or missing edges.

Initially, the side where the supports are "fat" and the corners are rounded, as if the resin accumulated during work had also been cured. It decreases the exposure time, it didn't work.

Bad resin?

I looked here in the group, but I didn't find anything relevant that would give me a solution.

Anyone using anycubic black who can give me a settings that works?

Anycubic Photon

Firmware version: 4.2.19.3

Slicer: Chitubox 1.6.3 (same problem in previous versions).

Resin: Anycubic Black (7/11 2020)

Slicer settings for black resin: Google Spreedsheet and others (all failed).

Good quality USB pen drive (same problem using anycubic pen drive)

翻譯年糕

So I am in love with the Elegoo water washable resins on my two photons. The detail is good, the layer time is 35% less than the standard elegoo grey, and support removal is easy. With my current process I wash my resin and put the waste water away in a container and my plan is to evaporate out the water from these containers, cure the leftover resin and dispose of it properly. Would a consumer water distillation machine be an option as an alternative? Basically run the waste water through it to "clean" the water so its good enough to reuse? The leftover resin/chemicals in the distillation chamber could be scooped out and cured/disposed of properly. I wouldn't assume the "clean" water is clean enough to dispose of down sink but probably good enough to reuse to wash more prints.

翻譯年糕

Hi all, 2 questions:

1. Has e.g. Anycubic Eco resin really low-level smell compared to common Anycubic resin?
2. What is the fastest way to let smell evaporate from cured model? Heat/fan/water/...?

翻譯年糕

OK, another noobie question (sorry). I've worked on CAD for years and years and we have a solidscape wax machine. But I've just bought a Photon S to prototype a few bits and to produce things like the attached pic in small numbers. No matter how many ways I place supports and angle the item on the bed, also trying different settings I still end up with a model that has issues with slightly wrinkled surfaces or sagging. Am I chasing rainbows here, or is a usable item achievable, model is 45mm long. Thanks

翻譯年糕

hola chicos. tengo un problema con pantalla LCD ,la cambien por una nueva y no hubo problemas hasta hace 2 dias que empezo a darme un error T88,he desconectado y conectado otra vez el cable de la pantalla LCD y sigue con el mimo error T88,sabeis que podria ser? actualizare el software? que software nuevo instalo? aqui os dejo fotos y video del problema y el software que tengo instalado en mi photon. un saludo y gracias

翻譯年糕

Okay, I need some clarification. I received my Photon from my sons for Christmas, and the prints using Anycubic transparent yellow with the default slicer settings look great.

I bought a bottle of SainSmart grey resin, and that brand isn't listed on the spreadsheet. I am using the settings for Monoprice grey, but I'm not getting the ultra fine details that I had with the Anycubic resin.

Example: the Medieval Castle printed near perfectly in yellow. The sphere at the top of the center spire was even there. The same model in grey, and I lost all of the cones, and the sphere is gone.

Could this be just a small adjustment to exposure time? I have the standard Photon and I haven't tried Chitubox yet.

I'm at work now, so I can't add a photo, but I will later. Thanks in advance for any help.

翻譯年糕