Anycubic Photon Printer Owners 造訪社團 » UV

原文網址 Francis Lapointe
2019-04-27 01:30:05

I would like to know wich source of UV light you use to cure your printings. I use the sun but i would like to create some kind of lightbox, if you have any suggestions, show me your setup :)

翻譯年糕

Robert Silvers
2019-04-27 01:44:04

Richard Shapiro
2019-04-27 06:36:43

Robert Silvers
2019-04-29 03:18:31

原文網址 GoldenGoose Gifts
2019-04-26 23:08:56

Hi everyone this is a great group. I did a great first print on my new machine. I did a second print and got some whiting on the print. Has anyone got any suggestions to what it is. I believe I cleaned and cured ok with my uv lamp.

翻譯年糕

Timmo Hellemann
2019-04-26 23:12:35

Bob Deblier
2019-04-26 23:13:09

GoldenGoose Gifts
2019-04-26 23:13:30

Fabian Rodriguez
2019-04-26 23:16:48

GoldenGoose Gifts
2019-04-26 23:18:50

原文網址 Dan Smith
2019-04-26 22:02:39

Curing in water! I think I have it. So this is what I’ve been doing lately and curing is much faster and no tacky effect post curing. also helps prevent warping from the UV heating the resin.
Wash in alcohol
Airbrush off what will come off.
Wash in water.
Airbrush dry
Cure for 30sec under UV
Place in water bath and cure until finished.
The secret is in curing for a short duration prior to placing in water bath. That means you can use tap water for the curing bath as the outer layer of resin is cured and doesn’t react with anything, no mineral deposits or white mineralization.
The resin really does cure much faster underwater (o2 prevents the resin curing), and the finished product is smooth, no marks and ready for paint and display.
Picture of a 1:160 paddock ripper, those tines are actually sharp!

翻譯年糕

Dan Hjulberg
2019-04-26 22:06:48

Dan Smith
2019-04-26 22:08:42

Kory Gregersen
2019-04-26 22:12:19

Richard Shapiro
2019-04-26 22:22:44

Dan Smith
2019-04-26 22:23:25

Krunoslav Zlomislic
2019-04-26 22:30:31

Dan Smith
2019-04-26 22:31:37

Richard Shapiro
2019-04-26 22:32:47

Dan Smith
2019-04-26 22:35:09

Mk IphoneNinja
2019-04-27 05:16:00

Chris Hunt
2019-04-27 14:28:47

Mason Chapman
2019-05-04 20:01:29

Dan Smith
2019-05-04 20:07:19

Mason Chapman
2019-05-04 20:15:03

Dan Smith
2019-05-04 20:16:03

Dan Smith
2019-05-04 20:17:16

Mason Chapman
2019-05-04 20:21:24

原文網址 Kevin Patrick Sullivan
2019-04-26 06:06:49

I love the look of Siraya Blu under UV.

翻譯年糕

Juan Perez
2019-04-26 06:08:32

Juan Perez
2019-04-26 06:09:14

Kevin Patrick Sullivan
2019-04-26 06:10:34

Juan Perez
2019-04-26 06:11:40

Todd Jones
2019-04-26 06:13:39

Kevin Patrick Sullivan
2019-04-26 06:18:49

Todd Jones
2019-04-26 06:22:43

原文網址 Michael Paulick
2019-04-25 23:30:05

Made the plunge and bought a Photon. Probably somewhere in this group it has been asked, but...
This is what I have gleaned reading posts here about pre-print set up, but what are the steps to post processing your prints (7 and up)?
1. Shake your resin
2. Shake it some more.
3. Pour into vat, but not too much.
4. Wait for bubbles to pop.
5. Hit 'Go!' on your model.
6. Wait
7.
I know there is the UV curing, the IPA/RA cleaning, the storing of unused resin, etc, but what order does this all happen in and how/why is it done?

翻譯年糕

Matthew Toad
2019-04-25 23:36:59

Michael Paulick
2019-04-25 23:39:28

Matthew Toad
2019-04-25 23:41:04

Michael Paulick
2019-04-25 23:42:25

Travis McGeathy
2019-04-25 23:50:50

Danny Lloyd
2019-04-26 00:04:36

Patrick Vida
2019-04-26 00:08:47

David Howlett
2019-04-26 00:09:59

Vinicius Silva
2019-04-26 00:11:22

Sen Kun
2019-04-26 00:15:23

Bernie Horowitz
2019-04-26 00:25:31

Horris Borris
2019-04-26 00:30:04

Michael Paulick
2019-04-26 01:25:36

Horris Borris
2019-04-26 01:32:08

Silas Bo Nielsen
2019-04-26 02:51:08

Jason Bitter
2019-04-26 03:01:07

Daylan Agirre-Gray
2019-04-26 03:15:49

Francesco Ostili
2019-04-26 03:36:39

Bernie Horowitz
2019-04-26 03:52:10

Matt Kuhn
2019-04-26 03:56:36

Ryan Moffett
2019-04-26 03:58:07

Michael Paulick
2019-04-28 08:28:46

Michael Paulick
2019-04-28 08:29:11

Breno Azevedo
2019-04-29 01:50:19

原文網址 Dylan Sawatzky
2019-04-25 08:20:50

Hi, all you 3d printing veterans. It's been great reading through and getting a sense of the anycubic line and what to expect.

Flash sale on amazon.ca today with the hype I was getting on here. I'll get my first printer(non S photon) Monday.

Just 2 quick questions.

1:) Is the anycubic green resin a decent balance between quality/budget/first-timer-friendly

B, is it best to build a curing solution out of UV led tape lighting or that Chinese nail-curing station that I see people using?

Thanks for being inclusive and a great community.

翻譯年糕

Noah Singer
2019-04-25 08:25:11

Michael Van Kesteren
2019-04-25 08:25:11

Guajolote Messias
2019-04-25 08:26:00

Dylan Sawatzky
2019-04-25 08:31:50

Dylan Sawatzky
2019-04-25 08:32:19

Regan Fairbanks
2019-04-25 08:58:42

Mark Wardle
2019-04-25 09:10:26

Alex Clarke
2019-04-25 10:54:30

Jared Zadorozny
2019-04-25 14:31:17

Jared Zadorozny
2019-04-25 14:32:59

Dylan Sawatzky
2019-04-25 14:34:35

Sen Kun
2019-04-25 14:38:27

Jared Zadorozny
2019-04-25 14:38:45

Sen Kun
2019-04-25 14:40:14

Jared Zadorozny
2019-04-25 14:40:15

Sen Kun
2019-04-25 14:41:19

Sen Kun
2019-04-25 14:44:07

Dylan Sawatzky
2019-04-25 14:44:54

Jared Zadorozny
2019-04-25 14:46:14

Jared Zadorozny
2019-04-25 14:46:22

Jared Zadorozny
2019-04-25 14:46:45

Jared Zadorozny
2019-04-25 14:50:50

Samuel Herrera
2019-04-25 17:05:31

Francesco Ostili
2019-04-25 17:17:58

Gary Houser
2019-04-25 22:09:56

Rich Newman
2019-04-27 08:58:43

Gary Houser
2019-04-27 09:03:54

原文網址 Thomas Roager
2019-04-25 01:41:23

Hi Everyone i just ordered the Original photon and have A few questions ?

1. Anyone tried to change uv light source to something that gives more light / spread the up light more ?

2. Is the filtering fan doing anything good and is that the only part making lost of noise on the printer ?

3. Is the z axis mod with linear rails worth it ?

Thanks ?

翻譯年糕

Hector Felix
2019-04-25 01:47:28

Thomas Roager
2019-04-25 01:48:53

Sen Kun
2019-04-25 02:11:16

Thomas Roager
2019-04-25 02:15:32

Sen Kun
2019-04-25 02:16:08

Sen Kun
2019-04-25 02:17:34

Thomas Roager
2019-04-25 02:17:50

Vinicius Silva
2019-04-25 04:10:11

Thomas Roager
2019-04-25 04:11:14

Robert Silvers
2019-04-25 06:21:56

Dustin Skye
2019-04-25 12:23:37

原文網址 Tom Franco
2019-04-25 01:13:50

Question regarding post-print UV curing.
If I can still smell the resin would the prints be under-cured?
If they are quite brittle/weak how do I know if they need to be cured more or less? (I know of the nail test, but I'm not sure that it wouldn't also happen if I burnt the print with the UV light)
Thanks

翻譯年糕

Bob Deblier
2019-04-25 03:06:19

原文網址 Shane Graber
2019-04-24 10:28:30

I'm working on a highly flexible UV resin for MakerJuice and I'd like to get some feedback on it. It's very stretchy and could make some very interesting parts; however, I don't know how well it will print supports given how much it stretches and flexes. Here's a couple videos of a part printed with this prototype resin. What does the group think of this prototype? Would it be of interest or is it too flexible?

翻譯年糕

Andrew Burton
2019-04-24 15:53:32

Ivan Antharon Antalec
2019-04-24 16:36:11

Mike Tree
2019-04-24 17:10:22

Harrison Labadi
2019-04-24 18:07:35

Shane Graber
2019-04-24 19:19:22

Ivan Antharon Antalec
2019-04-24 19:21:05

Andrew Burton
2019-04-24 19:21:24

Shane Graber
2019-04-24 19:23:56

Mike Tree
2019-04-24 19:29:21

Andrew Burton
2019-04-24 19:35:26

Susan Sioux Mercer
2019-04-24 20:49:23

Tay Chauhan
2019-04-24 20:50:09

Shane Graber
2019-04-24 22:40:58

Shane Graber
2019-04-24 22:42:20

Shane Graber
2019-04-24 22:45:08

Tay Chauhan
2019-04-24 22:49:24

Shane Graber
2019-04-25 01:57:20

Keith Holmes
2019-04-25 03:27:56

Mike Tree
2019-04-25 04:26:39

Shane Graber
2019-04-25 04:27:20

Shane Graber
2019-04-29 03:30:03

Gabriel Marian Alfons
2019-09-09 04:13:02

Gabriel Marian Alfons
2019-09-12 16:31:31

原文網址 Gary Houser
2019-04-24 02:32:49

Ok here is a pic of the uv leds inside the bucket I built for a curing light. Easy build. Use tape uv leds was $19.99 off amazon, I had the bucket. This is the one I used it came with the power supply. It doesnt need to be the water proof type so shop to find what will work best for you. It takes about 10mins to cure a mini. Note hitech clear support in center :)

https://www.amazon.com/ANJAYLIA-16-4…/…/ref=sr_1_fkmrnull_1…

翻譯年糕

全不選發文排行