Anycubic Photon Printer Owners 造訪社團 » UV

原文網址 Vinicius Silva
2018-11-23 07:49:39

So for the Moai Photon face off I found out why the Photon Failed the print.

So when i started print yesterday i stopped the file before the photon had done the home switch checking. and then i turned the printer off and rebooted it

Turns out this messed up the zero position. and no matter how i tried setting the new zero the print would always start at the origin.

Solution was to reset the EEPROM by running the factory settings.gcode file that can be found under firmware folder on photonsters.org

i did some before and after videos of a file print

ANYCUBIC , Amy Liao , Xinfu Xie you should look into this.

Normal Printing Before EEPROM reset
https://photos.app.goo.gl/wirQnJsHaAVUvuN56

Normal Printing After EEPROM reset
https://photos.app.goo.gl/j6afyoeRnpD3Wtj66

Photon vs Moai Face Off post
https://www.facebook.com/groups/AnycubicPhoton/permalink/1509752599169377/

# BugHunterz

翻譯年糕

Sen Kun
2018-11-23 13:32:54

Chris Meijer
2018-11-23 14:58:58

Chris Meijer
2018-11-23 14:59:24

Vinicius Silva
2018-11-23 17:52:27

Chris Meijer
2018-11-23 19:11:37

Chris Meijer
2018-11-23 23:23:49

Anthony Clifton
2018-11-23 23:41:21

Vinicius Silva
2018-11-24 00:08:14

Chris Meijer
2018-11-24 00:47:31

Vinicius Silva
2018-11-24 00:53:32

Chris Meijer
2018-11-24 00:54:26

Vinicius Silva
2018-11-24 01:01:00

Chris Meijer
2018-11-25 18:30:43

Chris Meijer
2018-11-25 18:51:44

Vinicius Silva
2018-11-25 21:53:28

Chris Meijer
2018-11-25 21:57:19

Marvel Mendoza
2019-06-15 18:09:33

Vinicius Silva
2019-06-15 19:01:37

Marvel Mendoza
2019-06-15 19:03:32

Alex Vee
2019-06-15 19:25:23

Jake Morley
2019-06-15 22:09:29

Vinicius Silva
2019-06-16 06:05:29

原文網址 Nathaniel Silva Nerona
2018-11-22 09:33:10

Where to get the recommended UV lamp to use to cure prints? US locations. What wattage works best?

翻譯年糕

Anthony Clifton
2018-11-22 10:22:32

原文網址 Stefano Corinaldesi
2018-11-21 14:35:10

hand made smooth resin
100 micron layer high
70 mm in 4 hours
washed without IPA
uv cured
no post processing

翻譯年糕

原文網址 巫国勝
2018-11-20 21:25:20

anyone tried to change the uv source to other wavelengths and try new resins?

翻譯年糕

El Ner Endem
2018-11-20 21:49:11

巫国勝
2018-11-20 21:55:34

Martin Guhl
2018-11-21 00:18:17

巫国勝
2018-11-21 00:22:57

Martin Guhl
2018-11-21 00:44:08

Robert Maefs
2018-11-21 02:41:01

巫国勝
2018-11-21 07:12:39

Robert Maefs
2018-11-21 07:49:48

Philipp Maitrot
2018-11-22 07:29:56

Robert Maefs
2018-11-22 07:36:58

Philipp Maitrot
2018-11-22 08:21:45

巫国勝
2018-11-22 08:22:33

Philipp Maitrot
2018-11-22 08:22:50

巫国勝
2018-11-22 08:23:38

Philipp Maitrot
2018-11-22 08:24:40

巫国勝
2018-11-22 08:26:19

Philipp Maitrot
2018-11-22 08:26:19

巫国勝
2018-11-22 08:27:54

巫国勝
2018-11-22 08:28:27

Philipp Maitrot
2018-11-22 08:31:14

巫国勝
2018-11-22 08:34:57

Philipp Maitrot
2018-11-22 08:41:38

Philipp Maitrot
2018-11-22 08:43:20

巫国勝
2018-11-22 08:44:34

Philipp Maitrot
2018-11-22 08:46:51

巫国勝
2018-11-22 08:48:10

巫国勝
2018-11-22 08:48:51

Philipp Maitrot
2018-11-22 08:48:54

原文網址 Chris Kaczmarczyk
2018-11-20 07:06:40

I've recently purchased a reptile heating pad and controller for use with my Photon since it is in a shed outside. The controller is set to 70F, but it seems even when the temp outside reaches the highest point of the day, the temp probe (placed right next to the vat) is still only reaching about 60F.

So for those of you with heating pads, how did you set them up? They don't seem effective enough for winter use. I'm considering using the foam the Photon came packed in as additional insulation, but I'm worried that once the UV screen starts heating up it may be too much.

翻譯年糕

Joe Broggio
2018-11-20 07:20:47

Maximillian Martinez
2018-11-20 08:05:16

Richard Shapiro
2018-11-20 09:13:10

Marc Fischer
2018-11-20 12:35:34

Chad Elstad
2018-11-20 13:24:59

Chris Kaczmarczyk
2018-11-20 14:01:44

Chris Kaczmarczyk
2018-11-20 14:04:39

Alex Vee
2018-11-20 18:43:36

Chad Elstad
2018-11-20 23:02:37

原文網址 Daniel Prasał
2018-11-20 06:41:51

Hi. I have ordered recently Anycubic grey resin on Amazon UK and received slightly different bottle than usual. It was quite suspicious in a first thought but left it on the shelf until run out of remaining resin. Then opened and notice that resin has different grey shade than usual. Anyway run a print and all failed. After few adjustment of printing parameters I got some better results, but still not the quality that should expect from genuine resin. Also prints are very rubbery before uv curing and brittle after. In the batch from Amazon seller I had 3 bottles. Two of them were in typical bottle, on in different. But after closer look on the correct bottles I found that label colours are a bit off to the genuine. Just wondering if anyone experienced this with your orders. It looks that the resin is not the genuine product from Anycubic. I would appreciate any comment from Anycubic support here if you read that. On the photo the left bottle is genuine, others seems to be fake.

翻譯年糕

Lucas Azd
2018-11-20 06:45:09

Nick Williams
2018-11-20 06:45:19

Lucas Azd
2018-11-20 06:47:10

Lucas Azd
2018-11-20 06:48:38

Giancarlo Arriola
2018-11-20 06:48:44

Lucas Azd
2018-11-20 06:49:08

Nick Williams
2018-11-20 06:50:38

Vinicius Silva
2018-11-20 06:51:32

Nick Williams
2018-11-20 06:51:54

Miro Jurić
2018-11-20 06:53:42

Lucas Azd
2018-11-20 06:54:05

Benny Woolley
2018-11-20 06:55:54

Daniel Prasał
2018-11-20 06:55:57

Joe Broggio
2018-11-20 06:57:13

Benny Woolley
2018-11-20 06:58:31

Joe Broggio
2018-11-20 07:00:05

Kostas Filosofou
2018-11-20 07:01:01

Savio Ku
2018-11-20 07:09:43

Mark Wardle
2018-11-20 07:14:07

Miro Jurić
2018-11-20 07:35:21

Adam Widdowson
2018-11-20 07:44:16

Chayanin Somton
2018-11-20 11:18:40

Sf Yip
2018-11-20 12:50:03

Paul Tyer
2018-11-20 17:28:02

Christopher Botha
2018-11-21 17:11:08

Sen Kun
2018-11-21 17:57:55

原文網址 John Norton
2018-11-19 04:32:34

Thanks for letting me in :)
I have one but...... its in a box until Christmas!!
I've some more resin, a box of filter funnels, some alcohol and a UV nail light (which my wife found hilarious!) on route. I already have face masks from airbrushing.

Any suggestions for anything else I need or should I just find some cool 28\56\72mm minis for when I get to play with real detail (until then the Ender 3 will just have to do ;) )

翻譯年糕

Micah Vestal
2018-11-19 04:35:33

Rose Stumpwater
2018-11-19 04:37:33

Rose Stumpwater
2018-11-19 04:38:49

John Norton
2018-11-19 04:40:07

Micah Vestal
2018-11-19 04:41:41

John Norton
2018-11-19 04:42:13

Rose Stumpwater
2018-11-19 04:45:00

Horris Borris
2018-11-19 06:27:17

John Norton
2018-11-19 06:29:27

John Norton
2018-11-20 03:45:25

Rose Stumpwater
2018-11-20 04:04:41

John Norton
2018-11-20 04:21:08

John Norton
2018-11-20 04:29:44

Rose Stumpwater
2018-11-20 04:30:58

John Norton
2018-11-20 04:31:44

原文網址 Eric Keezer
2018-11-19 03:43:27

Any solutions? I’m getting white flaking debris in my models. I’m using Anycubic Black resin. After screwing a 1/4 inch metal bolt through a printed female threaded hole, bits of white plastic flake off. I clean with IPA after, then tap water, then UV cure for 10 minutes. The threads work well, with little friction, but of course some plastic is shaved off. I expected it to be black, but it’s white. Ideas?

翻譯年糕

Eric Keezer
2018-11-19 03:55:04

Eric Keezer
2018-11-19 03:58:29

Simon Jackson
2018-11-19 04:08:04

Philipp Maitrot
2018-11-19 04:27:38

Philipp Maitrot
2018-11-19 04:32:10

Eric Keezer
2018-11-19 04:42:29

Eric Keezer
2018-11-19 04:45:44

原文網址 Ian Hawkins
2018-11-18 18:03:38

Just ordered a photon on an Amazon deal, Looking for recommendations for uv curing equipment. I've seen some mention of nail polish curing lamps, are these tall enough? I'll likely be printing 28mm gaming stuff off.

翻譯年糕

Mark Niesche
2018-11-18 18:06:01