Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Wayne Peters
2020-03-06 18:48:17

Do you folk clean the vat with alcohol or just wipe dry? Would alcohol damage the transparent vat film?

翻譯年糕


原文網址 Wayne Peters
2020-03-06 18:30:19

Note to self: When changing the film in the vat remember to remove the protective film from both sides or effectiveness can be seriously impaired.

Sigh.

翻譯年糕


原文網址 Wayne Peters
2020-02-14 17:09:20

Okay, so this is the second machine in a row which, after very little use has suffered the 11800 curse. (Where it crashes mid print because it mistakenly thinks the USB stick has been removed)
I've updated the firmware. I've tried multiple USB sticks and plugged them directly into the mother board. All to no avail.
Here's something odd, though. If I run a dry print (with no resin in the vat) it runs perfectly. Once I add resin I get 11800 sometimes as late as 80% through.
Current theory: vibration of cured resin being pulled from the vat causing a disconnect which suggests a physical fault somewhere.
Is there anything else I can try before I send this one back as well?

翻譯年糕

Andrew Steel
2020-02-14 17:45:11

Wayne Peters
2020-02-14 18:11:46

Wayne Peters
2020-02-14 18:21:36

Wayne Peters
2020-02-14 18:48:10

Wayne Peters
2020-02-14 18:49:04

Andrew Steel
2020-02-14 18:55:23

Wayne Peters
2020-02-14 19:11:38

Niall Forrester
2020-02-14 19:12:42

Wayne Peters
2020-02-14 19:14:49

Niall Forrester
2020-02-14 19:23:40

Chris Bondy
2020-02-14 19:34:46

Wayne Peters
2020-02-14 19:39:25

Wayne Peters
2020-02-14 19:42:21

Wayne Peters
2020-02-14 19:44:59

Chris Bondy
2020-02-14 19:45:04

Chris Bondy
2020-02-14 19:46:25

Niall Forrester
2020-02-14 20:52:52

Niall Forrester
2020-02-14 20:54:32

Wayne Peters
2020-02-15 00:45:04


原文網址 Wayne Peters
2020-02-05 18:24:53

How often do you folks change the clear screen in the base of the vat?
I think mine's still in pretty good condition but there must be a reason the prints are preferring to stick to it rather than the plate (yes, the plate is level and a paper width from the screen).

翻譯年糕

James Cachia-Garrett
2020-02-05 18:28:44

Cam Erasmus
2020-02-05 18:30:09

Wayne Peters
2020-02-05 18:34:17

Wayne Peters
2020-02-05 18:35:00

Nipuna Gunarathne
2020-02-05 18:41:38

David Chalk
2020-02-05 18:42:28

Sean Smith
2020-02-05 19:21:32

Wayne Peters
2020-02-05 19:38:01

Gary Priest
2020-02-05 20:05:33

Phlavio Spr
2020-02-05 20:49:31

Gary Slovinsky
2020-02-06 00:56:57

Jeremy Babcock
2020-02-06 06:09:14

Wayne Peters
2020-02-06 06:14:14

Jeremy Babcock
2020-02-06 06:18:19

Jeremy Babcock
2020-02-06 06:20:08

Miroslav Zajíček
2020-02-06 14:38:20


原文網址 Wayne Peters
2020-02-05 16:45:50

After a series of fails yesterday I discovered that my machine's 'home' position was about a mm above the screen. I performed the paper leveling and once I was happy with the level I pressed Z=0 and was presented with 'Z-zero is decided by trigger position.' Confirm/Cancel.
I chose Confirm and all seemed well until I pressed 'Home' again and found that the plate returned to about a mm above the screen, the new Z having not been set.
Anyone know what I'm doing wrong?

翻譯年糕

Merv Hinton
2020-02-05 16:46:50

Daniel Kottmair
2020-02-05 16:49:18

Niall Forrester
2020-02-05 16:52:10

Matt Bertwell
2020-02-05 16:53:19

Matt Bertwell
2020-02-05 16:53:27

Wayne Peters
2020-02-05 17:09:35

Wayne Peters
2020-02-05 17:15:56

Wayne Peters
2020-02-05 17:17:47

Niall Forrester
2020-02-05 17:30:18

Wayne Peters
2020-02-05 17:44:09

Niall Forrester
2020-02-05 18:58:05

Niall Forrester
2020-02-05 18:59:19

Wayne Peters
2020-02-05 19:09:54


原文網址 Wayne Peters
2020-02-04 21:46:47

What are the possible causes of resin not adhering to the print plate? I've had two partial failures in a row where the support skate has partly come away from the print bed during printing, deforming the printed part.
I'm using Elegoo grey and the base is curing for 60 seconds and the layers for 10.

翻譯年糕

Brendan Wood
2020-02-04 21:49:07

Mark Wardle
2020-02-04 21:53:38

Kris Leon
2020-02-04 21:56:31

Wayne Peters
2020-02-04 22:01:18

Wayne Peters
2020-02-04 22:32:33

Wayne Peters
2020-02-05 00:21:37


原文網址 Wayne Peters
2020-01-15 22:08:42

Another question I have is about alcohol. The machine came with two bottles of 70% which I'm not convinced is cleaning the prints properly. I've seen the recommended 90% for sale but I've also seen 100% too.
Is 100% better or is it too much and I should stick to 90%?

翻譯年糕

David Thach
2020-01-15 22:10:28

Dan Elent
2020-01-15 22:11:07

Brian Gabriel
2020-01-15 22:21:53

Wayne Peters
2020-01-15 22:50:33

John Smith
2020-01-15 22:59:18

Rory Kostman
2020-01-16 06:37:00

Nick Walker
2020-01-16 20:10:59

Nick Walker
2020-01-16 20:12:11

John Smith
2020-01-18 05:43:44


原文網址 Wayne Peters
2020-01-15 21:52:28

If I get a UV nail curing lamp, do I have to be certain it's 405nm or doesn't it matter?
ie can it be any nm (wavelength?) it just takes longer to cure or some such?
Does the wattage matter?

翻譯年糕

Marcin Bocis
2020-01-15 21:55:28

Bob Deblier
2020-01-15 21:56:14

Paul West
2020-01-15 21:56:30

Wayne Peters
2020-01-15 22:05:45

Jim Stephens
2020-01-15 22:20:25

Jim Stephens
2020-01-16 00:03:11

Keith Yinger
2020-01-16 00:33:07


原文網址 Wayne Peters
2019-11-23 17:46:20

I did a print yesterday using the green transparent resin that comes with the printer. By the time it was finished it was dark outside so I've had to wait until this morning to put it in the window for UV curing. It's had a couple of hours now in admittedly dull, overcast daylight and still feels a bit gooey and oily on the surface. I've had pretty good results with green before now. Have I done something wrong?

翻譯年糕

Sunny Shukla
2019-11-23 17:58:49

Wayne Peters
2019-11-23 18:15:07

Sunny Shukla
2019-11-23 18:18:31

Wayne Peters
2019-11-23 18:33:50

Wayne Peters
2019-11-24 00:41:39

Sunny Shukla
2019-11-24 00:45:53


 

討論主題

全不選 常用關鍵字