Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Dave Williams
2019-02-28 19:06:51

I started a print just over 2 days ago and there is about a half hour to go, it's a print of a starship to the full build dimensions, I didn't realise that I had set Layer value to 0.02 which was for previous miniatures of 10mm, I will post a an image when I get home, anyone else done the same

翻譯年糕

Richard Thomas
2019-02-28 19:11:17

Ayman Abdallah
2019-02-28 19:23:43

Orwin SantaCruz
2019-02-28 20:37:19

Richard Thomas
2019-02-28 21:26:56

Dave Williams
2019-03-01 05:08:46

Andrew McKay
2019-03-01 05:37:56

Dave Williams
2019-03-01 20:06:50

Dave Williams
2019-03-01 20:08:40

原文網址 Dave Williams
2019-02-17 06:02:02

Printed some 10mm figures for a 1/350 battleship

翻譯年糕

Kevin Boogaard
2019-02-17 06:55:48

Dave Williams
2019-02-18 04:20:32

原文網址 Dave Williams
2019-02-17 03:07:05

Had a print going overnight, this is the result, I thank God the resin never got out in the printer

翻譯年糕

Andrew Beaton
2019-02-17 04:33:23

Carlos R. Puebla
2019-02-17 04:45:09

Ron Luttrull
2019-02-17 05:24:01

Tom Sargison
2019-02-17 06:31:17

Hosung Kim
2019-02-17 07:54:19

Jannick Langfahl
2019-02-17 08:28:56

Dave Williams
2019-02-17 20:30:16

Jason Odegard
2019-02-17 20:54:50

GaryAnji Smith-Lambeth
2019-02-18 08:54:30

Dave Williams
2019-02-18 17:25:08

GaryAnji Smith-Lambeth
2019-02-19 02:51:29

原文網址 Dave Williams
2019-02-10 01:08:59

Alien, from slicer to finish, . 03

翻譯年糕

Richard Thomas
2019-02-11 21:59:03

Mike Foreman
2019-02-24 23:59:27

原文網址 Dave Williams
2019-02-06 00:36:23

Latest figure finished 9cms

翻譯年糕

Ana Hulse
2019-02-06 00:39:56

Dave Williams
2019-02-06 14:37:14

原文網址 Dave Williams
2019-02-03 20:13:31

The mix of grey and green I did turned out the right colour for these

翻譯年糕

原文網址 Dave Williams
2019-02-03 07:50:32

I just tried an experiment, I had a bit of grey resin left in the tank, that was the last of it, looking around I still had some green clear resin left over, so in it went and I mixed it with the grey, started a print, three hours later, the prints came out great

翻譯年糕

Jim Leenan
2019-02-03 10:28:36

Matthew Dillon
2019-02-03 12:49:07

原文網址 Dave Williams
2019-01-10 20:06:08

Settings for these two in Anycubic photo slicer, using Anycubic grey
Layer thk 0.04
Exp time 16
Off time 5
Bottom Exp time 85
Bottom layers 8
X size 68.04
Y size 120.96
Z size 150
Chitubox settings
Machine
Resolution
X 1440
Y 2560

X 68.04
Y 120.96
Z 150
Print
Layer height 0.04
Bottim layers 8
Exp time 16
Bottom Exp time 85
Light off delay 0
Bottom light off delay 0

翻譯年糕