Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Thiérry Fortunér
2019-01-13 11:54:34

Any advice on printing this? I'm thinking I'm going to hollow it and I want to print it straight upside down, but I feel like I should angle it somehow. Thoughts?

翻譯年糕

Puren Bulat
2019-01-13 13:28:48

Thiérry Fortunér
2019-01-13 13:48:55

原文網址 Thiérry Fortunér
2019-01-10 06:58:05

Are the default settings for the supports in the Slicer available anywhere? I was messing with some stuff but now I can't get it back to normal.

翻譯年糕

Marshall Tearle
2019-01-10 07:04:09

原文網址 Thiérry Fortunér
2019-01-08 02:59:08

How do you figure out resin cost per print

翻譯年糕

Dustin Scott
2019-01-08 03:04:05

Gazsó Péter
2019-01-08 03:08:30

Daniel Warchol-Anderson
2019-01-08 03:08:42

Thiérry Fortunér
2019-01-08 03:49:28

James Paull
2019-01-08 04:52:24

Chad Elstad
2019-01-08 05:16:07

Richard Shapiro
2019-01-08 05:18:36

Thiérry Fortunér
2019-01-08 05:30:22

Zena Andreou
2019-01-08 05:42:53

原文網址 Thiérry Fortunér
2019-01-04 05:32:51

How toxic is cured resin dust? I'm using a dremel on some cleaned and cured parts, I have glasses, gloves, and mask, is that enough?

翻譯年糕

Aleksandr Naumov
2019-01-04 05:38:19

James Cachia-Garrett
2019-01-04 05:50:53

Che Fielding
2019-01-04 06:12:01

Thiérry Fortunér
2019-01-04 06:16:18

Dave Williams
2019-01-04 06:42:22

Tony Boutwell
2019-01-04 07:00:25

Thiérry Fortunér
2019-01-04 07:00:55

Jason Clements
2019-01-04 07:12:00

James Cachia-Garrett
2019-01-04 07:40:02

Guti Gutmann
2019-01-04 11:49:32

Jason Clements
2019-01-04 20:06:43

原文網址 Thiérry Fortunér
2019-01-01 07:31:03

Too many supports or not enough supports?

翻譯年糕

Thiérry Fortunér
2019-01-01 07:31:18

El Ner Endem
2019-01-01 07:34:16

Sam Ross
2019-01-01 07:41:10

Thiérry Fortunér
2019-01-01 07:54:56

Sam Ross
2019-01-01 07:55:54

Thiérry Fortunér
2019-01-01 07:56:06

Thiérry Fortunér
2019-01-01 12:29:31

Sam Ross
2019-01-01 13:26:14

Thiérry Fortunér
2019-01-01 14:18:16

Lex Cole
2019-01-02 04:26:34

Tycho Pandelaar
2019-01-02 04:41:04

原文網址 Thiérry Fortunér
2019-01-01 07:20:13

I'm dumb. Is there a way to remove individual holes generated in Meshmixer?

翻譯年糕

Jeremy Lauzon
2019-01-01 08:45:56

Thiérry Fortunér
2019-01-02 03:02:25

Jason Clements
2019-01-02 07:36:35

原文網址 Thiérry Fortunér
2018-12-28 17:14:44

New question. I printed the one on the right at a 30° angle, the one on the left was flat to the base. The bottom on the right one is all goey and doesn't have the details of the flat one. Also it had weird distortions on the flat parts on the side. Any advice?

翻譯年糕

Sen Kun
2018-12-28 17:37:34

Thiérry Fortunér
2018-12-28 17:40:08

Thiérry Fortunér
2018-12-28 17:40:24

Sen Kun
2018-12-28 18:02:11

Thiérry Fortunér
2018-12-29 03:06:22

原文網址 Thiérry Fortunér
2018-12-27 19:23:25

So what's causing this? The flat parts on the bottom (the parts facing the plate) have these wavy ugly parts. The top parts (furset away from the plate) turned out fine

翻譯年糕

Luke Forrest
2018-12-27 19:28:22

Gaius Nötigenfalls
2018-12-27 19:32:14

Benjamin Matthews
2018-12-27 19:36:10

Gaius Nötigenfalls
2018-12-27 19:37:05

Thiérry Fortunér
2018-12-27 19:38:59

Thiérry Fortunér
2018-12-27 19:39:16

Sen Kun
2018-12-27 20:02:32

Sen Kun
2018-12-27 20:12:09

Nemo Vilpponen
2018-12-27 22:05:26

Gazsó Péter
2018-12-27 22:08:04

Stephen Butt
2018-12-28 02:29:18

Thiérry Fortunér
2018-12-28 11:20:14

原文網址 Thiérry Fortunér
2018-12-21 14:39:53

Dumb question. I live in an apartment and the resin smell is really bad when it's running. I build a vent tube to the outside and attached it to your fans on the back of the photon but it still stinks. If I put a box or some sort of cover over the entire Photon while it's printing to keep the smell in will it cause any issues, like overheating?

翻譯年糕

Israel Perez
2018-12-21 14:45:21