Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Drew Doll
2020-03-27 04:35:48

What do people use to help bring more flexibility to their prints? I've seen a few products claiming it prints a flexible material but they are fairly expensive.

翻譯年糕

Greg Chapman
2020-03-27 05:04:09

5% Monocure rapid flex

Jacob Hale
2020-03-27 05:05:41

Adding a 30% ratio of flex 100 to an existing resin will improve the flexibility, the higher the ratio, the higher flexibility. Not cheap of course, but I've never seen a truly flexible resin that was cheap. Siraya ABS-like is my go to for base resin, but I can't find it anywhere ATM.

原文網址 Drew Doll
2019-12-24 14:57:43

I have pieces of a miniature I need to glue together. I've tried some hobby glue as well as super glue and neither does the trick. Any suggestions?

翻譯年糕

Rose Stumpwater
2019-12-24 14:58:49

Louis Siciliano
2019-12-24 14:59:43

Khristian Sutherland
2019-12-24 15:00:49

Chris Hunt
2019-12-24 15:01:12

Drew Doll
2019-12-24 15:02:42

Tim Moulton
2019-12-24 15:11:10

Sydnee Davidson
2019-12-24 15:16:24

Stefan Giudici
2019-12-24 15:18:01

Aaron Vèrsiontwo
2019-12-24 15:20:00

Jarin Udom
2019-12-24 15:30:26

Adam Horton
2019-12-24 15:45:22

Michael Fieweger
2019-12-24 16:27:01

John Rhodes
2019-12-24 18:50:53

Robert Mako Sharkey
2019-12-24 19:47:54

Aaron McCommon
2019-12-24 23:27:14

原文網址 Drew Doll
2019-12-20 13:06:45

Is it safe to mix different resins together? I have small bit of the green resin I got when I got my printer and I hate to waste it. The other resin I have is more anycubic resin just a different colour

翻譯年糕

Yessik Ziiq
2019-12-20 13:09:17

Smith Hayward
2019-12-20 13:10:20

Jarin Udom
2019-12-20 13:11:08

Israel HV
2019-12-20 15:08:47

Smith Hayward
2019-12-20 21:57:16

James Edward
2019-12-20 22:53:03

Smith Hayward
2019-12-20 23:02:17

James Edward
2019-12-20 23:03:57

原文網址 Drew Doll
2019-11-23 06:50:51

I've been currently having a problem with my last few prints. Inconsistent sticking to the build plate. Its never in the same location.

I did 3 prints over the past 24hrs. The 1st print had the item on the right side not stick to the plate. The 2nd print every thing stuck to the plate fine, and for the 3rd one it was only half of the left side not sticking to the plate.

I'm unsure if its my print settings that are messed up or something else.

翻譯年糕

Zäta Doe
2019-11-23 06:54:42

Drew Doll
2019-11-23 07:26:35

Mark Rhodes
2019-11-23 07:39:36

Zäta Doe
2019-11-23 15:32:26

Mike McCreery
2019-11-23 22:44:01

Victor K Durango
2019-11-23 23:33:08

Zäta Doe
2019-11-23 23:51:47

原文網址 Drew Doll
2019-11-21 17:39:16

Would a carbon filter attached to the exhaust port of the OG photon make it safe enough to be placed in my home? I currently have it out in my garage but it is expensive to have the garage heated all the time for the printer.

翻譯年糕

Tiernan Messmer
2019-11-21 17:41:40