• 3D列印服務
  • COSPLAY 3D 建模
  • #maker+t=market
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Jeremiah Chetwood
2019-12-26 02:38:26

Well in 2hrs19min I will see if my print came out. So far looks good....

翻譯年糕


原文網址 Jeremiah Chetwood
2019-12-25 11:50:04

5 times now I have leveled checked settings and this is what I get.

翻譯年糕

Scott Colvin
2019-12-25 11:51:29

Vernon Babich
2019-12-25 11:51:57

Tom Chandler
2019-12-25 11:54:01

Nipuna Gunarathne
2019-12-25 11:58:25

Michael Beal
2019-12-25 12:05:31

Randy Shepherd
2019-12-25 12:12:48

Vernon Babich
2019-12-25 12:13:17

Michael Beal
2019-12-25 12:13:47

Jeremiah Chetwood
2019-12-25 12:14:11

Blaze Dodd
2019-12-25 12:18:34

Vernon Babich
2019-12-25 12:20:25

Jeremiah Chetwood
2019-12-25 12:27:49

Jeremiah Chetwood
2019-12-25 12:38:16

Vernon Babich
2019-12-25 12:40:16

Robert Small
2019-12-25 12:41:31

Robert Small
2019-12-25 12:41:46

Robert Small
2019-12-25 12:42:28

Robert Small
2019-12-25 12:43:21

Christian Mendez
2019-12-25 13:18:02

Stefan Giudici
2019-12-25 13:34:37

Jeremiah Chetwood
2019-12-25 13:37:45

Jeremiah Chetwood
2019-12-25 13:39:12

Jeremiah Chetwood
2019-12-25 13:39:45

Jeremiah Chetwood
2019-12-25 13:41:32

Otto Rey
2019-12-25 14:01:29

Chris Bondy
2019-12-25 14:14:04

Alex Munro
2019-12-25 14:18:21

Jaco Norchie Nortje
2019-12-25 14:55:12

Dan Arden
2019-12-25 15:03:52

Jarin Udom
2019-12-25 15:25:48

Krunoslav Zlomislic
2019-12-25 15:41:29

Luigi Gabriel
2019-12-25 16:25:29

Luigi Gabriel
2019-12-25 16:26:07

Brian Jenkins
2019-12-25 17:36:18

Tycho Pandelaar
2019-12-25 19:33:21

Kevin West
2019-12-25 20:07:43

Daniel D'Intino
2019-12-25 22:18:52

David Lester
2019-12-25 22:26:08

Rael Naem
2019-12-25 22:35:15

Jerry Doyle
2019-12-26 00:17:30

Ron Lumsden
2019-12-26 00:53:52

Brian T Patterson
2019-12-26 02:04:14

Wm Kuch
2019-12-26 03:42:37

Olivier Nicolas
2019-12-26 04:01:44

Daniel Devon Johnson-King
2019-12-26 04:04:04

Vernon Babich
2019-12-26 04:10:43

Michael Steadham
2019-12-26 06:54:37

Reggie Grahita Adhyatmaka Djatni
2019-12-27 17:52:28

Michael Steadham
2019-12-27 19:31:59


原文網址 Jeremiah Chetwood
2019-12-25 05:57:03

Well I have tried to print a figure so far in just sticks to fep, I have leveled each time, tried different settings????

翻譯年糕

Ryan Neal
2019-12-25 06:00:37

Olivier Nicolas
2019-12-25 06:05:47

Tyson Moran
2019-12-25 06:16:09

Brian King
2019-12-25 06:22:06

Adam Horton
2019-12-25 06:27:32

Alexander Bayerdorffer
2019-12-25 07:03:35

Jerry Doyle
2019-12-25 07:42:42

Alexander Bayerdorffer
2019-12-25 07:49:28


原文網址 Jeremiah Chetwood
2019-12-24 12:44:59

Looking for good fep sheet too...
.

翻譯年糕

Terry Reed
2019-12-24 12:57:34

Melecio Guzman
2019-12-24 13:48:09


原文網址 Jeremiah Chetwood
2019-12-24 12:40:50

I was looking for a good castable resin, any preferences, I have anycubic eco resin. Thank you

翻譯年糕


原文網址 Jeremiah Chetwood
2019-12-24 09:42:56

Here is my test print. Looks like some got left out.....???? Maybe to close to edge?????

翻譯年糕

Nipuna Gunarathne
2019-12-24 09:44:29

Joe Sands
2019-12-24 10:09:12

Jeremiah Chetwood
2019-12-24 10:48:11


原文網址 Jeremiah Chetwood
2019-12-23 20:53:38

Well I check test print out this morning, looks like it came out just fine

翻譯年糕


原文網址 Jeremiah Chetwood
2019-12-23 09:33:20

Going to run the test print see if it comes out, if it does then my ring design are not what the should be.....good night all

翻譯年糕


原文網址 Jeremiah Chetwood
2019-12-23 09:21:37

Well stuck to the fep again going to clean up call it a day, have to get up at 345 for work

翻譯年糕

Jake Walker
2019-12-23 09:31:37

Russell Beer
2019-12-23 09:47:59

Brian T Patterson
2019-12-23 09:48:36

Kris Leon
2019-12-23 14:52:48

Kris Leon
2019-12-23 14:53:35


原文網址 Jeremiah Chetwood
2019-12-23 08:09:45

I'm doing a few rings to try. Ran through slicer did supports , med and auto support.

翻譯年糕

Tim Moulton
2019-12-23 08:10:49

Jeremiah Chetwood
2019-12-23 09:19:46


 

討論主題

全不選 常用關鍵字