Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Thomas Holm
2020-03-21 18:58:11

First FEP-puncture, due to user-error.

Will exchange it using the advice from this group and the internet.
Hoping it will be un-complicated.

由於使用者錯誤, 第一次fep-puncture.

將利用這個團體和網際網路的建議來交換.
希望它不會複雜.

· 查看原文 · 為此翻譯評分

Kyle Urban
2020-03-21 19:01:32

Meh, the screws can be (very) stuck. As long as you don't strip them you are fine.

Nathan Madche
2020-03-21 19:09:37

Bottle cap method works great. Don't worry to much about tuning it just tighten the bolts one spin at a time alternating screws kind of like putting on a tire if that helps

Merv Hinton
2020-03-21 19:09:45

https://www.youtube.com/watch?v=DLi3chV43LQ

Thomas Holm
2020-03-21 19:58:01

And done.
Used the bottle cap and the Spectrum app. Got a nice high ping. Now running the first test print.

原文網址 Thomas Holm
2020-03-13 01:10:48

I find myself stopping next to my Photon S, holding my breath, counting down, waiting for that ‘twerp’. Anyone else?

我發現自己停在我的光子s旁邊, 屏住呼吸, 倒計時, 等待那個" twerp 還有誰?

· 查看原文 · 為此翻譯評分

Derek Fontes
2020-03-13 01:14:29

Billz Sharif
2020-03-13 01:22:29

Peter Csaki
2020-03-13 01:38:02

Ernest Sandridge Ill
2020-03-13 01:38:52

Thomas Holm
2020-03-13 01:50:01

Justin Bullock
2020-03-13 01:56:52

Ernest Sandridge Ill
2020-03-13 02:01:21

Merv Hinton
2020-03-13 03:16:09

Thomas Holm
2020-03-13 03:17:38

Keith Yinger
2020-03-13 03:47:42

Thomas Holm
2020-03-13 03:49:51

Joel Mendoza
2020-03-13 06:36:07

Mark Wardle
2020-03-13 06:58:18

Thomas Holm
2020-03-13 15:23:25

Andrew Steel
2020-03-13 22:16:45

Thomas Holm
2020-03-13 23:07:03

Thomas Holm
2020-03-13 23:07:28

Thomas Holm
2020-03-14 05:07:26

Keith Yinger
2020-03-14 05:46:39

原文網址 Thomas Holm
2020-03-12 00:58:40

My first technical fail. The build plate came loose and unlevelled. So the base is uneven and there is a layer shift some 4 cm up. So will need to re-level and tighten that srew better.
At the same time I'm very impressed. Apart from the layer shift the print quality is great! (0.01 mm, 7 s main layers, 60 s baselayer, Anycubic Green Transparent that came with the machine.) Two spots where I need to move a support (Thank You 3DPrintingPro), but other than that actually a great print.
So thank you all for the advice you give here and on other platforms.

我的第一個技術失敗. 構建板鬆散並解開. 所以基地是不均衡的, 有一個層移大約4釐米. 所以, 需要重新調整並收緊這個更好.
同時, 我印象深刻. 除了層層輪換, 列印質量也很棒! (0.01 mm, 7 s主層, 60 s baselayer, 任何與機器一起帶來的綠色透明.)兩個我需要移動支援的兩個地方(謝謝3 dprintingpro) , 但除此之外, 實際上是一個偉大的印刷品.
所以感謝大家在這裡和其他平台上的建議.

· 查看原文 · 為此翻譯評分