After nearly cutting my fingers off using a razor to remove prints, I made a simple jig to hold the build plate without putting pressure on leveling bolt.
Edit:
I think the reason I have so much trouble removing parts is because I'm printing flat mechanical parts (gears etc) directly on the plate, no supports or rafts to help removal. I need to use a razor to reduce damage. Probably have the bottom layer exposure too high also.
翻譯年糕
James Richmond
2020-03-19 01:56:03
Brian King
2020-03-19 01:57:02
Stan Westmoreland
2020-03-19 01:57:52
Li Sandro
2020-03-19 01:59:55
Christian Sargent
2020-03-19 02:02:41
Frank Seel
2020-03-19 02:04:00
Emile Belanger
2020-03-19 02:04:17
Michael Joseph
2020-03-19 02:05:31
Brian King
2020-03-19 02:06:26
Brian King
2020-03-19 02:07:19
John Driggers
2020-03-19 02:07:22
Frank Seel
2020-03-19 02:07:52
Samuel Colt
2020-03-19 02:10:20
Lucas Parard
2020-03-19 02:13:50
Ale Anton
2020-03-19 02:14:35
Dylan Hancox
2020-03-19 02:19:40
Derek Reihe
2020-03-19 02:20:37
Dylan Hancox
2020-03-19 02:21:06
Stan Westmoreland
2020-03-19 02:32:10
Jason Willis
2020-03-19 02:33:13
罗西晟
2020-03-19 02:33:58
Tobias Langer
2020-03-19 02:38:53
Juan Tron
2020-03-19 02:56:25
Lora Delvecchio
2020-03-19 02:56:38
Shawn Clifton
2020-03-19 02:57:35
Shawn Clifton
2020-03-19 02:58:26
Clifford Schwankner
2020-03-19 03:01:56
Leavon Archer
2020-03-19 03:07:13
Evan Boone
2020-03-19 03:08:51
Mark Wardle
2020-03-19 03:20:23
Keif Davies
2020-03-19 03:28:20
Attila Maros
2020-03-19 03:33:48
DreamBox Prod
2020-03-19 03:41:58
Vishal Vij
2020-03-19 03:46:47
Dan Barca
2020-03-19 03:55:02
Kane Gibson
2020-03-19 03:57:51
George Bulte
2020-03-19 04:08:05
James Forder
2020-03-19 04:09:48
Tim Moulton
2020-03-19 05:01:41
Angelo Daniele Perlin
2020-03-19 05:11:59
Chris Roberts
2020-03-19 06:02:20
Rupert Dunn
2020-03-19 07:00:29
Rupert Dunn
2020-03-19 07:04:04
Clifford Schwankner
2020-03-19 07:05:44
Don Mason
2020-03-19 08:35:45
John VanRyn
2020-03-19 09:17:13
Thomas Harrell
2020-03-19 09:21:43
Matthew McCoy
2020-03-19 10:03:04
Sam Griffiths
2020-03-19 10:33:03
Bob Deblier
2020-03-19 13:48:05
Steve Ross
2020-03-19 14:26:17
Adam Short
2020-03-19 15:58:08
Adam Short
2020-03-19 15:58:34
Dalibor Matuska
2020-03-19 17:06:38
Emile Belanger
2020-03-19 17:50:30
Dragut Gruia Matei
2020-03-19 19:43:39
Ronald Roten
2020-03-20 00:26:43
Neal Conway
2020-03-20 02:28:04
Joseph Bochinski
2020-03-20 11:59:24
Patrick Samuel
2020-03-20 12:23:52
Juan Pablo Bagnon
2020-03-20 13:05:17
Brenton-Amanda York-DeBoef
2020-03-20 18:18:28
Adam Scaramella
2020-03-20 19:11:39
Tom Sargison
2020-03-20 20:08:55
Emile Belanger
2020-03-20 20:28:04
Juan Pablo Bagnon
2020-03-21 05:33:07
