Anycubic Photon Printer Owners 造訪社團

原文網址 Stephen Mitchell
2020-03-03 06:32:31

So I had some long tank barrels come out of center and mis printed.

Wondering if this is z axis wobble and how do I correct it?

翻譯年糕

Ian Gill
2020-03-03 06:38:46

Stephen Mitchell
2020-03-03 06:43:11

原文網址 Michael Szita
2020-03-03 06:27:29

Pic for attention. On my original Photon after having to deal with a stripped screw that stopped me from popping off the bottom/front panel to swap out the LCD, I've finally I stalled the new LCD, and it seems to work fine but now when I went to level the build plate I cant move the build plate at all, no grinding, the rod still moves with my fingers.

Not sure what could have happened, aside from needing a new LCD it was working fine prior to the LCD swap. Tried resetting the EEPROM but still nothing when I try to move the Build plate.

Any ideas?
EDIT: Checked the motor cable, still secure on both ends.

翻譯年糕

Brandon Ray
2020-03-03 06:54:37

Tom Sargison
2020-03-03 21:51:37

Michael Szita
2020-03-04 01:32:20

Michael Szita
2020-03-04 01:32:54

Kirk Sturgulewski
2020-03-04 01:38:53

Michael Szita
2020-03-04 01:40:08

Kirk Sturgulewski
2020-03-04 01:41:07

Michael Szita
2020-03-04 01:45:25

Kirk Sturgulewski
2020-03-04 01:58:47

Michael Szita
2020-03-04 03:06:13

Sen Kun
2020-03-04 08:29:23

Michael Szita
2020-03-04 11:52:48

原文網址 Nemanja Lacedaemon Enomotarch Đe
2020-03-03 06:03:56

Hi.Does anyone have photon and Wanhao duplicator D8? :)

翻譯年糕

Janne Sjöström
2020-03-03 06:31:46

Nemanja Lacedaemon Enomotarch Đe
2020-03-03 06:45:38

Janne Sjöström
2020-03-03 06:52:43

Janne Sjöström
2020-03-03 06:52:48

Janne Sjöström
2020-03-03 06:52:50

Nemanja Lacedaemon Enomotarch Đe
2020-03-03 06:57:10

Janne Sjöström
2020-03-03 07:07:34

Nemanja Lacedaemon Enomotarch Đe
2020-03-03 07:52:55

原文網址 Miroslav Zvoneček
2020-03-03 06:03:51

Tak mám za sebou první tisk na Photon S. Testovací model se vytiskl bez problémů. Zkusil jsem druhý - litofanii. Už jsem si myslel, že to umím ;-) Zkusil jsem to rovnoběžne s deskou. Ale podívejte, co se mi vytisklo. Kde jsem udělal chybu?

翻譯年糕

Zena Andreou
2020-03-03 06:21:10

Miroslav Zvoneček
2020-03-03 06:24:17

Zena Andreou
2020-03-03 06:27:10

原文網址 Vinicius Silva
2020-03-03 06:00:15

Artur Kawa
2020-03-03 06:32:05

Vinicius Silva
2020-03-03 06:35:44

Elvin Torok
2020-03-03 07:39:18

Vinicius Silva
2020-03-03 07:46:53

Elvin Torok
2020-03-03 07:47:53

Vinicius Silva
2020-03-03 07:49:04

Elvin Torok
2020-03-03 07:54:23

Vinicius Silva
2020-03-03 12:11:52

Janus Stark
2020-03-03 13:50:33

Elvin Torok
2020-03-03 16:22:16

原文網址 Mika Gruszka
2020-03-03 05:29:14

Recent prints. I'm sure a good bit of you are familiar with this file from thingiverse. So happy with the outcome! Each of these is about 2 inches long for the skull.

File- https://www.thingiverse.com/thing:473639

翻譯年糕

原文網址 Jeremiah Chetwood
2020-03-03 05:27:04

Ok I'm trying to use my air brush syphon fed and the air blows out the bottle. I have taken it apart use brushes to clean scrub everything. What am I missing??? Wanted to prime print

翻譯年糕

David Newton
2020-03-03 05:30:13

David Newton
2020-03-03 05:32:41

原文網址 Josh Gray
2020-03-03 05:19:27

Some people have spoken with me about how SLA models go soft or lose detail after a number of years, due to an internal chemical reaction... Does anyone know about this?? ? 翻譯年糕

Liam Kaiser Wilhelm Smith
2020-03-03 05:22:56

Josh Gray
2020-03-03 05:23:13

Ben Wood
2020-03-03 05:26:03

Liam Kaiser Wilhelm Smith
2020-03-03 05:26:53

Christopher Fugate
2020-03-03 05:38:11

Chris Hunt
2020-03-03 05:45:07

Scott Pavlich
2020-03-03 05:51:06

Alwin Chan
2020-03-03 05:52:25

Gabe Snooks
2020-03-03 05:59:03

Robert Maefs
2020-03-03 06:18:13

Jim Carswell
2020-03-03 06:29:29

Travis Callahan
2020-03-03 08:39:42

Liam Kaiser Wilhelm Smith
2020-03-03 08:50:44

Brandon Marcussen
2020-03-03 08:55:04

Jason Willis
2020-03-03 14:23:49

Chris Hunt
2020-03-03 14:24:08

James Cachia-Garrett
2020-03-03 15:02:21

Chris Hunt
2020-03-03 15:02:45

原文網址 Kyle Standring
2020-03-03 04:54:35

using chitubox 1.6.3, when i go back into a saved project and try to edit a support, in this case by adjusting the height, it moves the support completely off the model. Anyone else experiencing this or have a work around?

翻譯年糕

Ryan Shelvik
2020-03-04 10:47:37