Anycubic Photon Printer Owners 造訪社團

原文網址 Joshua Meyer
2020-02-11 08:45:25

Noob Question: If a very small edge of the raft is just outside the print area, will that small portion just not print, or cause the overall print to fail?

翻譯年糕

Jeremiah Chetwood
2020-02-11 08:48:25

Michael Fairley
2020-02-11 08:56:53

Will Koone
2020-02-11 08:58:19

Joshua Meyer
2020-02-11 09:00:19

Richard Humble
2020-02-11 12:00:16

原文網址 Frank Ramsay
2020-02-11 08:20:34

I’ve been doing some test prints of a base topper design I’m working on and couldn’t get the exposure dialed in... then noticed significant uneven exposure. ?
I’m trying to debug this problem, and could use some help.
This is on an original Photon, so is this the LCD starting to fail? Or maybe the UV light becoming uneven?

翻譯年糕

Brendan Wood
2020-02-11 08:40:56

Frank Ramsay
2020-02-11 08:43:56

James Forder
2020-02-11 09:31:40

Frank Ramsay
2020-02-11 10:11:10

Frank Ramsay
2020-02-11 10:11:45

Frank Ramsay
2020-02-11 10:26:21

Frank Ramsay
2020-02-11 10:27:44

Frank Ramsay
2020-02-11 11:00:38

Brendan Wood
2020-02-11 11:06:44

Frank Ramsay
2020-02-11 11:29:25

Frank Ramsay
2020-02-11 12:04:36

Brendan Wood
2020-02-11 12:08:47

Richard Humble
2020-02-11 15:45:02

Frank Ramsay
2020-02-11 19:55:46

Frank Ramsay
2020-02-12 23:36:55

原文網址 Casey Galloway
2020-02-11 08:03:40

Still not sure how to read these. I see other people's posts, and I guess a result different than the others. I'm guessing 7, what about you? Hard to get a good shot if this test strip.

翻譯年糕

James Cachia-Garrett
2020-02-11 08:19:26

Casey Galloway
2020-02-11 08:35:42

James Cachia-Garrett
2020-02-11 08:44:46

Casey Galloway
2020-02-11 08:50:45

Bob Deblier
2020-02-11 14:36:28

原文網址 Anthony Strafaccia
2020-02-11 07:49:51

Bulbasaur!

https://www.thingiverse.com/thing:2673525

原文網址 David Altman
2020-02-11 07:45:04

Hey everyone, I am having a sudden issue. So, I have been printing for a couple months now, with no real issues (outside of not enough supports and stuff on user error). Now, I'm trying to print a simple box. Each side is separate so i stacked them side by side, tilted them so i could put some supports to prop it up and help ensure that its a good print. However, its been 5 tires and they all fail. It prints the base of the supports, then starts to print the lower supports, and fails after a few layers into the actual print. I'm at a loss. I tried tilting, adding/sub supports, printing each side by itself, changed the resin, tested the UV light, re-leveled a few times and more. Its a little cold in the room, but still within range of the bottle recommendations. Any ideas?

翻譯年糕

Alwin Chan
2020-02-11 07:47:28

David Altman
2020-02-11 07:49:17

Alwin Chan
2020-02-11 07:50:44

David Altman
2020-02-11 08:01:39

Dan Elent
2020-02-11 08:11:48

Dan Elent
2020-02-11 08:12:42

David Altman
2020-02-11 08:18:28

David Altman
2020-02-13 03:42:45

Alwin Chan
2020-02-13 07:31:29

David Altman
2020-02-13 07:36:23

David Altman
2020-02-13 07:37:29

Alwin Chan
2020-02-13 08:07:28

David Altman
2020-02-13 08:22:59

原文網址 Fred Breton
2020-02-11 07:42:21

原文網址 Coire Ruff
2020-02-11 07:32:03

Printer arrived today. Was supposed to come with 1.5 liters of resin....supposed to. Lol

Already dropped customer service a line to find out where the resin is. The printer is pretty...but, useless until I get the resin. Heh

翻譯年糕

Mike Tate
2020-02-11 07:36:04

Handrez Pintubola
2020-02-11 07:58:39

Anthony Fennell
2020-02-11 08:10:52

Will Koehler
2020-02-11 10:34:30

Coire Ruff
2020-02-11 23:54:05

Coire Ruff
2020-02-11 23:55:08

原文網址 Javier Luis
2020-02-11 07:10:37

hello i have some problems, i tried to print many times this cube 6x6x6 with supports and the supports are smaller than i want and the cube its good but from top to bottom is 7 mm no 6

翻譯年糕

Mark Wardle
2020-02-11 07:40:08

Javier Luis
2020-02-11 07:43:00

Mark Wardle
2020-02-11 07:45:20

Javier Luis
2020-02-11 07:45:39

Mark Wardle
2020-02-11 08:01:46

Miroslav Zajíček
2020-02-11 17:25:39

原文網址 Chase Fenner
2020-02-11 07:10:13

I do not know what i am doing wrong and could use some help. This seems to mainly only be a problem when using grey. The printer for some reason always prints this thin layer of flimsy film right in the middle. It usually still successfully prints with that hanging off or Tangled up in the supports.

Then for some reason the fep is loosening and being to get tightened every couple of prints. I have gone through 3 fep sheets trying to fix. I have done the normal and Flint method of leveling and the uv light and screen looks fine in the machine. Any ideas?

翻譯年糕

George Bulte
2020-02-11 07:16:35

Nipuna Gunarathne
2020-02-11 14:04:51

原文網址 Adam Rodgers
2020-02-11 06:50:03

Thanks for accepting me. I am a 3D sculptor and a client just sent me a Photon this morning as a surprise. As a complete non techy person expect me to ask for help a lot :) Will be unboxing tomorrow and setting the little beauty up.