Anycubic Photon Printer Owners 造訪社團

原文網址 Sean Smith
2020-02-08 10:31:12

Well. Did my absolute best to get as much detail as I could with shading. The horns look awesome!! Painted them black then used grey to highlight the lines.

It was really freaking windy today so I could not put a primer coat on outside. I will do another thin coat to smooth out the paint and then put the clear coat on tomorrow if it’s nice out.

Once it’s dry I will add shading to the underside as well to enhance the lines.

What do you all think???

翻譯年糕

Sean Smith
2020-02-08 11:49:11

原文網址 Emre Güneş
2020-02-08 10:30:56

Hello guys please share me chitubox support settings please :) ? ?

翻譯年糕

原文網址 Hutch Heberer
2020-02-08 10:23:56

Do you use the Auto Support feature or do you place your own Supports usually? I am using Chitubox and looking for more reccomendations.

翻譯年糕

Eric Sieracki
2020-02-08 10:25:32

Daniel Quinn
2020-02-08 10:28:17

Johnny Grant
2020-02-08 10:28:38

Brendan Wood
2020-02-08 10:30:12

Jason Rowell
2020-02-08 10:31:12

Alexander Bayerdorffer
2020-02-08 10:51:28

Chad Elstad
2020-02-08 10:51:36

Vincent Balmont
2020-02-08 11:00:32

Hugh Jeriolas
2020-02-08 11:04:48

Jorge Salazar
2020-02-08 12:01:35

Chris Thiessen
2020-02-08 12:04:00

Susan Sioux Mercer
2020-02-08 15:08:47

Kenneth Johansen
2020-02-08 16:13:06

John Nash
2020-02-08 17:46:23

Mark Wardle
2020-02-09 01:42:56

Chris Holden
2020-02-09 09:20:43

Barthels Marvels
2020-02-10 11:55:57

原文網址 Franyely Montiel
2020-02-08 10:12:42

My printer just started making that sound, it's normal?

翻譯年糕

Mark Anderson
2020-02-08 10:15:25

John Smith
2020-02-08 10:16:50

Nikki Maisala
2020-02-08 15:38:34

Simon C Day
2020-02-08 18:23:52

原文網址 Fernando Cay Diarte
2020-02-08 10:11:24

Would anyone be kind enough to indicate the most appropriate settings for chitubox supports for warcraft miniatures of approximately 35 mm? Thank you very much in advance

翻譯年糕

原文網址 Clark Paints
2020-02-08 09:28:11

When you all fill your beds (I mean wall to wall) do you ever have problems with the model beginning to come off. So far no issues. I try to always fill the bed. It’s never the same are but a corner or side may start to come of. The greatest peel has been perhaps 1/3 the total surface area of the base. 8BaseLayers.

翻譯年糕

Vincent Balmont
2020-02-08 09:40:03

Jim Nelson
2020-02-08 10:07:27

Niall Forrester
2020-02-08 15:02:52

原文網址 Davy Struyf
2020-02-08 09:13:36

It finished! Biggest print yet. 29 hours at 0.02. OG photon with elegoo transparent red. Dragon bust by print your monsters. Man what a great model and print. Absolutely love the elegoo trans red.

結束了! 最大的列印. 29小時0.02. og photon與elegoo透明紅色. 通過列印你的怪獸來破壞龍. 夥計, 多麼偉大的模特和列印. 絕對喜歡elegoo trans紅色.

· 查看原文 · 為此翻譯評分

Rovic Pejida
2020-02-08 09:15:55

Davy Struyf
2020-02-08 09:17:13

Keith Douglas Ahlstrom
2020-02-08 09:38:57

Gregory Akin
2020-02-08 11:12:14

Davy Struyf
2020-02-08 20:18:33

Chris Thompson
2020-02-08 20:27:02

Davy Struyf
2020-02-08 22:21:02

原文網址 Gabriel Guzman
2020-02-08 09:12:37

So far so good... ? ?

翻譯年糕

Rob Walker
2020-02-08 09:38:14

Gabriel Guzman
2020-02-08 11:11:01

原文網址 Alec Traynor
2020-02-08 09:05:00

Brand new owner. I’m doing the test cube with my Photon and I can already tell that my print failed.

1. I assume I can just stop the print and extract it?
2. Is the most common reason for failure not leveling your bed correctly?
3. What is the correct level of resin to put in the vat?
Thank you.

翻譯年糕

Bill Connelly
2020-02-08 09:10:24