Anycubic Photon Printer Owners 造訪社團

My original thumb drive that came with the photon finally died. Any suggestions on a replacement or does it really not matter?

翻譯年糕

Hello guys! I have a problem my Axial dont move more after att 4.2.19. A tried donwgrade for 4.2.18 and continued It.

翻譯年糕

Anyone know if this is a direct swap to replace the screen? Ordering from Anycubic isn't the best option at this point.

Thabks!

有人知道這是不是直接交換來取代螢幕? 從任何cubic訂購現在不是最好的選擇.

Thabks!

· 查看原文 · 為此翻譯評分

[SOLVED] Only the base sticks to the build plate! Hello all! I've been having issues lately with my Photon and I can't figure out what's going on with it. It was printing great but it suddenly stopped working. The base of my prints sticks to the build plate, but once it starts with the support material it gets stuck to the FEP. I changed the FEP, since it was a bit cloudy and scratched up, but same thing happens with the new FEP. The protective layer is removed. My room is at 20ºC, the resin is new, (Anycubic Grey, well stirred) and I've re-leveled (paper and flint reed method) so may times I'm going crazy with it. I printed the exposure test and I'm printing at 12sec exposure (85s bottom, 8 layers, 0.05mm) . I tried up to 20sec exposure but same results. Any help will be greatly appreciated! 翻譯年糕

Only went through the 500ml free bottle, went to clean the tank to use the white, notice there is a tiny mark on the fep feels like is about to crack any time soon, plus many other marks on it that I can feel with my finger, so I swapped out the fep.

Was in the process of testing dimensions accuracy with different exposure time, as I noticed the part aren't very dimensionally accurate so can't exactly build a model from the prints, after switching to white, it seems the white sticks much better to the plate than the green with the same print settings, all good ? , as long as it doesn't tear the fep when lifting, it now sounds its sticking much much better, I did use a bottle cap but that's after I put 2 screws down, one opposite to the other, not fully tighten till I put the cap in center, there was plenty loose before mounted on to the vat so hopefully I done that right, it's tight with some stretch after fitting to vat.

The reason I know it is stick much much better to the plate because I forgot AA was only on 1 when I sliced the model, so stopped it on 2nd layer to reprint with AA on 8,and it was a mission to get the 0.1mm of a print off the plate where as it was very easy with the green

翻譯年糕

So I have hit my first really failures. For some reason the machine keeps stopping at the same point just above the head. It doesn't seem like it is finishing the print just either because when I come back to the machine it is in the home screen instead of the screen asking you to confirm the job is done and the bed is not all the way up like it would normally be. Is it something in the sliceling? I did clean out the vat after the first print and find a single cured layer stuck to the fep.

翻譯年糕

Half a Skeletor, printing bottom half and base soon. Aaand yess I didn't clean him properly hence the white residue.

Elegoo grey. 7 bottom layers @ 65s, 7s per layer at 0.1 layer height.

翻譯年糕

Hi guys I’m totally new to this and I’m getting the printer today. Where do you guys get your files and also is there anything I should know straight off? I’m getting it from a friend. He’s barely used it as the smell messes with his sinuses

翻譯年糕

Lots talk about how low you can go (step size, I usually print .02 mm), but what about the other end of the spectrum, how big a step size can you print? I have a part I'm not too concerned with resolution and I'll be looking for a speedier print, so how large a step can I go and what's the trend with the exposure time?

翻譯年糕

Frame shearing is a thing and updating the firmware to 4.2.18 fixes it! Thank you for all your help!

翻譯年糕