Anycubic Photon Printer Owners 造訪社團

原文網址 Gregorey Savieo
2020-01-17 18:25:45

What do I do if the whole print bed and the thread is wobbly?! Ive seen some 2 rod upgrades and wobble stroppers...or do I just need to tighten something?

翻譯年糕

Nicolas Tsagarides
2020-01-17 19:25:03

原文網址 Bruce Piggott
2020-01-17 18:08:39

Hi, I have a problem with vertical streaks running through a model but only in a small area. This is a new problem and is in the machine not the print file.

I have two Photons so I was able to narrow down the problem. I thought it may be scratches on the vat base but exchanging the vat with the good machine did not fix the problem.

I removed the platform and vat and run a dummy print to look at the UV image. I noticed that in the area associated with streaks there are dim pinpricks of light that should not be there. So I deduce the problem is either the LCD display or the electronic drive to it.

Has anybody else had this problem?

Cheers, Bruce

翻譯年糕

Bruce Piggott
2020-01-17 19:01:06

原文網址 Giannis Andronkidis
2020-01-17 17:16:06

Brand new printer, right out of the box. Tried to turn it on a couple of times but the screen does not seem functional. Does anyone have a similar experience or even better a way to fix the problem ? Or should I just send it back and ask for a replacement?

翻譯年糕

Nipuna Gunarathne
2020-01-17 17:23:00

Justin Cupitt
2020-01-17 17:24:39

原文網址 Jacob Bolton
2020-01-17 16:37:04

I notice there are 2 layers of film on the fep do I need to take these off or is it ok the leave them on?

翻譯年糕

Michael Szita
2020-01-17 16:38:03

Charalambos Charalambous
2020-01-17 16:38:59

原文網址 Xaviour David
2020-01-17 16:21:25

So printer arrived far earlier than expected, still need to clear out the garage to make room for it. I've set it up underneath a verenda with the box over the top to block UV light and a blanket over it all to try and keep the inner heat level in the recomended range.

Is there anything wrong with this / is this a fire hazard?

Additionally anyone got exposure settings for anycubic red dialed in?

翻譯年糕

Sander van Deijl
2020-01-17 16:35:19

Xaviour David
2020-01-17 16:36:01

Nick Walker
2020-01-17 16:39:24

Nipuna Gunarathne
2020-01-17 16:56:21

原文網址 Neil Castle
2020-01-17 15:10:39

I printed my first multi-piece hollowed mini. The pieces don't fit together.

I used MeshMixer.

Am I STILL getting over exposure due to light bleed? My exposure time is already only 4 seconds.

Photon S
0.02
Elegoo Grey

Thoughts?

Thanks!

翻譯年糕

Sander van Deijl
2020-01-17 15:16:24

Richard Humble
2020-01-17 15:32:00

Neil Castle
2020-01-17 15:33:32

Neil Castle
2020-01-17 15:36:25

Richard Humble
2020-01-17 15:37:36

Sander van Deijl
2020-01-17 15:37:37

Richard Humble
2020-01-17 15:38:41

Patricia Rodríguez Torroba
2020-01-17 15:55:57

Neil Castle
2020-01-17 16:09:10

Justin Andrews
2020-01-17 16:12:57

Sander van Deijl
2020-01-17 16:31:57

Neil Castle
2020-01-17 16:55:41

Spencer Griffin
2020-01-17 17:28:05

Veda Toys
2020-01-17 19:48:36

Dominick Trascritti
2020-01-17 20:24:41

Joseph Daniels
2020-01-18 00:19:30

Jarin Udom
2020-01-18 02:08:40

原文網址 William Neal
2020-01-17 14:24:14

Hey guys I did the xp finder test. However I do not see any numbers at the bottom. Any idea what I'm doing wrong?

翻譯年糕

James Cachia-Garrett
2020-01-17 14:52:50

William Neal
2020-01-17 14:54:20

William Neal
2020-01-17 14:54:28

William Neal
2020-01-17 15:05:34

Stefan Giudici
2020-01-17 15:13:46

William Neal
2020-01-17 15:14:13

James Cachia-Garrett
2020-01-17 15:21:28

William Neal
2020-01-17 15:22:14

William Neal
2020-01-17 15:22:40

James Cachia-Garrett
2020-01-17 15:23:06

William Neal
2020-01-17 15:23:34

James Cachia-Garrett
2020-01-17 15:28:14

原文網址 Nathan J Hunt
2020-01-17 14:19:33

Well everyone I officially finished painting my model kit I printed from scratch on my anycubic photon... this is how the model turned out. I love my photon

翻譯年糕